Hi,
some days ago, I received two QLogic ISP2200, and today I got a HSSDC
cable to actually make use of my harddrives in my origin 3000. When I
try to install, at the stage of downloading base47.tar.gz, at some point
between 60% and 90% the installation stalls, and I see lots of the
messages below:
base47.tgz 82% |****************************** | 45934 KB -
stalled -isp0: possible command timeout on handle 2b6
isp0: possible command timeout on handle 2b7
isp0: possible command timeout on handle 2b8
...
many more of those
...
isp0: possible command timeout on handle 2ce
isp0: mailbox cmd (0x4000) with no waiters
isp0: possible command timeout on handle 2cf
...
isp0: possible command timeout on handle 2d2
isp0: LIP destroyed 642 active commands
isp0: possible command timeout on handle 2d3
...
isp0: possible command timeout on handle 2d8
isp0: mailbox cmd (0x4000) with no waiters
isp0: possible command timeout on handle 2d9
isp0: LIP destroyed 546 active commands
isp0: possible command timeout on handle 2da
...
isp0: possible command timeout on handle 2e2
isp0: mailbox cmd (0x4000) with no waiters
isp0: possible command timeout on handle 2e3
...
isp0: possible command timeout on handle 2e9
isp0: LIP destroyed 194 active commands
isp0: possible command timeout on handle 2ea
...
isp0: possible command timeout on handle 2eb
isp0: possible command timeout on handle 2ec
isp0: mailbox cmd (0x4000) with no waiters
isp0: possible command timeout on handle 2ed
isp0: LIP destroyed 194 active commands
isp0: possible command timeout on handle 2ee
...
isp0: possible command timeout on handle 1b7
isp0: possible command timeout on handle 1b8
isp0: Mailbox Command 'ABORT' failed (COMMAND PARAMETER ERROR)
isp0: watchdog timeout on handle 2b6
isp0: Mailbox Command 'ABORT' failed (COMMAND PARAMETER ERROR)
isp0: watchdog timeout on handle 2b7
isp0: Mailbox Command 'ABORT' failed (COMMAND PARAMETER ERROR)
isp0: watchdog timeout on handle 2b8
isp0: Mailbox Command 'ABORT' failed (COMMAND PARAMETER ERROR)
isp0: watchdog timeout on handle 2b9
isp0: Mailbox Command 'ABORT' failed (COMMAND PARAMETER ERROR)
...
until I Ctrl-C the installation.
I tried it with both cards, but I ran into the same problem.
Right now I switch back to boot from tftp/USB stick as before ;)
With this setup disk access was slow, but worked fine.
I have two 18GB FC disks in the box, sd0 as the main system disk, I
chose the automatically suggested partitons, and sd1 mounted on
/usr/ports. Formatting the disks after partitioning was no problem.
sd2 is just the USB stick still plugged in.
Is this something known, is there something in the L1 controller I
should check or anything else I could do?
below a a dmesg from the ramdisk:
cheers,
Sebastian
Initial setup done, switching console.
Copyright (c) 1982, 1986, 1989, 1991, 1993
The Regents of the University of California. All rights reserved.
Copyright (c) 1995-2010 OpenBSD. All rights reserved.
http://www.OpenBSD.org
OpenBSD 4.7-current (RAMDISK-IP27) #235: Thu Jun 10 04:38:08 MDT 2010
dera...@sgi.openbsd.org:/sys/arch/sgi/compile/RAMDISK-IP27
real mem = 1073741824 (1024MB)
rsvd mem = 20463616 (19MB)
avail mem = 994672640 (948MB)
mainbus0 at root: Origin 3000
cpu0 at mainbus0 nasid 0: MIPS R12000 CPU rev 3.5 400 MHz, R12000 FPU
rev 3.5
cpu0: cache L1-I 32KB D 32KB 2 way, L2 8192KB 2 way
clock0 at mainbus0 nasid 0: ticker on int5 using count register
xbow0 at mainbus0 nasid 0: XXBow revision 2
xbridge0 at xbow0 widget 15: XBridge revision 2
xbpci0 at xbridge0 bus 0: 33 MHz PCI bus
pci0 at xbpci0 bus 0
ioc0 at pci0 dev 4 function 0 "SGI IOC3" rev 0x01
onewire0 at ioc0
ioc0: ethernet irq 4, xbow irq 62
ioc0: superio irq 0, xbow irq 61
com0 at ioc0 base 0x20178: ns16550a, 16 byte fifo
com0: console
iec0 at ioc0: 128KB SSRAM, address 08:00:69:11:ca:be
nsphyter0 at iec0 phy 1: DP83843 10/100 PHY, rev. 0
dsrtc0 at ioc0: DS1742W
ohci0 at pci0 dev 5 function 0 "AT&T/Lucent USB 2-port" rev 0x10: irq 5,
xbow irq 60, version 1.0, legacy support
"TI TSB12LV22 FireWire" rev 0x01 at pci0 dev 6 function 0 not configured
usb0 at ohci0: USB revision 1.0
uhub0 at usb0 "AT&T/Lucent OHCI root hub" rev 1.00/1.00 addr 1
xbridge1 at xbow0 widget 14: XBridge revision 2
xbpci1 at xbridge1 bus 0: 66 MHz PCI bus
pci1 at xbpci1 bus 0
isp0 at pci1 dev 1 function 0 "QLogic ISP2200" rev 0x05: irq 1, xbow irq 58
isp0: board type 2200 rev 0x5, loaded firmware rev 2.2.6
scsibus0 at isp0: 512 targets, WWPN 210000e08b05371b, WWNN 200000e08b05371b
sd0 at scsibus0 targ 0 lun 0: <IBM, DRVL18L CLAR18, SG03> SCSI2 0/direct
fixed
sd0: 17356MB, 512 bytes/sec, 35546876 sec total
sd1 at scsibus0 targ 1 lun 0: <IBM, DRVL18L CLAR18, SG03> SCSI2 0/direct
fixed
sd1: 17356MB, 512 bytes/sec, 35546876 sec total
rd0: fixed, 10240 blocks
umass0 at uhub0 port 2 configuration 1 interface 0 "memory USB2.0" rev
2.00/2.00 addr 2
umass0: using SCSI over Bulk-Only
scsibus1 at umass0: 2 targets, initiator 0
sd2 at scsibus1 targ 1 lun 0: <memory, USB2.0, 1.00> SCSI2 0/direct
removable
sd2: 3931MB, 512 bytes/sec, 8051200 sec total
boot device: sd1
root on rd0a swap on rd0b dump on rd0b
