Hello Drogar, In attachment is the DOS obtained from your file.
I suggest that you give a look, if everything is ok, then the problem is with your eig2dos executable. []'s, --- Prof. Dr. Ihosvany Camps Instituto de Ciências Exatas. Sala Q203-J Universidade Federal de Alfenas. Unifal-MG Rua Gabriel Monteiro da Silva, 700 Centro. 37130-000. Alfenas. MG. Brasil Tel. +55 (35) 3299-1260 Skype: icamps Fax. +55 (35) 3299-1063 Twitter: @_icamps On Thu, May 2, 2013 at 12:10 PM, Drogar <[email protected]> wrote: > Hello > Thanks for ur suggestion. > > but again i had an error > > > > jafar@jafar-Aspire-5742G:~/Desktop/test/si$ ./Eig2DOS -s 0.02 -n 500 -m > 20 -M 10 -f < Si.EIG > Si.dos -h > bash: ./Eig2DOS: No such file or directory > jafar@jafar-Aspire-5742G:~/Desktop/test/si$ eig2dos < Si.EIG | tee dos.dat > eig2dos: command not found > jafar@jafar-Aspire-5742G:~/Desktop/test/si$ ./Eig2DOS Si.EIG | tee dos.dat > bash: ./Eig2DOS: No such file or directory > jafar@jafar-Aspire-5742G:~/Desktop/test/si$ > > this is my Si.EIG > > > > On Thu, May 2, 2013 at 6:16 PM, Uma Shankar Sharma > <[email protected]>wrote: > >> to plot DOS following procedure to be followed: >> (i) Put values exactly on the first line after the Fermi energy of >> SystemLabel.EIGsuch that 0.05 1000 -10 10 Here first value is (eta) >> precision second is >> (Ne) number of eigen values Third and last are min and max energy >> (ii) use command >> eig2dos < SystemLabel.EIG | tee dos.dat >> (iii) type gnuplot on terminal >> then use command >> plot 'dos.dat' w l >> >> If you again find some problem then send your SystemLabel.EIG I will >> check it >> >> >> With regards >> Dr U S Sharma >> RJIT, BSF Tekanpur >> Gwalior >> >> >> On Thu, May 2, 2013 at 4:07 PM, Nick Papior Andersen < >> [email protected]> wrote: >> >>> as it says, dont pipe the eig into eig2dos. >>> Do >>> >>> ./Eig2DOS Si.EIG | tee dos.dat >>> >>> Kind regards Nick >>> >>> 2013/5/2 Drogar <[email protected]> >>> >>>> Dear SIESTA user >>>> >>>> I had a problem with plotting DOS. I compiled Eig2DOS and transfer it >>>> into my Silicon file. >>>> I add "0.05 1000 10 -10 " to Si.EIG and then run - ./Eig2DOS < Si.EIG | >>>> tee dos,dat - then see >>>> >>>> Aspire-5742G:~/Desktop/si$ ./Eig2DOS < Si.EIG | tee dos,dat >>>> Usage: Eig2DOS [-d] [-s] [-l] [-m] [-M] [-b] [-B] [-h] EIGfile >>>> Use -h option for manual >>>> >>>> i run with Eig2DOS < Si.EIG | tee dos,dat and Eig2DOS < Si.EIG > >>>> dos.dat , too but see the same . >>>> >>>> what can i do with this to plot DOS.? >>>> >>>> every suggestion is helpful... >>>> -- >>>> with the best wishes... >>>> Jafar >>>> >>> >>> >> > > > -- > with the best wishes... > >
dos.dat
Description: Binary data
