For Kent, :-)
--
oozing on the muggy shore of the gulf coast
[email protected]
--- Begin Message ---
Greetings all,
Saw an interesting posting a while back (several) on timers and current
limiting.
The LM-555 first came out in 1969 as part of National Semiconductors
line of *Monolithic* technology. When CMOS (Complimentary Metal Oxide
Substrate) was invented it was also produced in that technology. The
LM-555 is now a standard workhorse in the electronic business.
The design is such that it can be operated in the Standard 12 volt
signal range or operated in the 5 volt TTL (Transistor-Transistor Logic)
signal range. Most of the CS circuits I have seen are operating in the
standard 12 volt signal range. The CMOS version can also operate in the
Standard 12 volt signal range or the TTL signal range. The difference
between the Monolithic and CMOS versions are the power dissipation. The
Monolithic version uses 10 ma at 15 volts, while the CMOS version uses
400 ua at 12 volts. The CMOS power dissipation is under 1 mw. That makes
it very good for battery operated circuits. The CMOS version in called
LMC-555. Thats L for Linear, M for Monolithic, and C for CMOS. See how
easy that is.:-)
Max supply voltage for the LM-555 is +18 volts and max supply for the
LMC-555 is +15 volts. Of course a good designer will never operate the
ICs at maximun ratings,unless he wants many failures. Operating at 12
volts gives a 20% safety factor.
A very easy to make adjustable current limiter can be made with only
two parts. An LM-317 three terminal regulator and a 250 ohm
potentiometer will do it. These are availible at any electronics place
at low cost, typically about $2.50 for the LM-317 and about $2.00 for
the petentiometer.
The three terminals are Vin, Vout, and Adj. The Vin terminal connects
to the power source, the Vout terminal goes to one end of the
potentiometer,the Adj terminal goes to the other end of the
potentiometer. (a potentiometer is a resistance element with a wiper
that moves over the resistence element, it has three terminals).
The end of the potentiometer that has the Adj wire attached to it goes
to the silver electrodes (the load). The center potentiometer terminal
(the wiper terminal) is connected to the Vout terminal. This mades the
potentiometer into the same thing as a rheostat ( a two connection
variable resister). To use it, place an milliamp meter in the cicuit and
adjust the *pot*(slang for potentiometer) for the current you want, and
thats where the current will stay. Of course there has to be current
flowing to start with, so wait until you have a good current flow before
you set it for what you want. The LM-117 can be used in place of the
LM-317. This is a little known use of the three terminal regulator.
Back to the LM-555. This timer has a dc coupled Darlington output
amplifier (push-pull). It is basically independent of the main timer ,
and can source or sink about 200 ma of current. Safely that is. Normally
we don`t push circuits close to max ratings, as stated before. Source
means the output can supply the current and sink means the output can
absorb ( receive) the current. In the source operation it is supplying
current from the power source of the timer. In the sink operation it is
receiving current from a separate supply thru a load. That feature makes
the LM-317 very useful in a wide range of circuits.
Bless you Bob Lee
--
oozing on the muggy shore of the gulf coast
[email protected]
--
The silver-list is a moderated forum for discussion of colloidal silver.
To join or quit silver-list or silver-digest send an e-mail message to:
[email protected] -or- [email protected]
with the word subscribe or unsubscribe in the SUBJECT line.
To post, address your message to: [email protected]
List maintainer: Mike Devour <[email protected]>
--- End Message ---