Reference:
http://web.idirect.com~showcase/althealth/cspulse.htm
Setup: 8oz distilled water in clear glass(no starters or salt added)
1/16 inch wide flat silver electrodes
2 1/2 wetted length
Electrode spacing 1 inch
Pulsed DC generator per above referenced web site
Pulse rate(frequency) 23.809KHz
Duty cycle on 54.54% off 45.45%
water temp around 70 degrees F
Electrodes wiped after run completed
Run time: 4hrs
Start: .12ma @ 7.4V(measured at electrodes with VOM)
(duty cycle affects the
measurements)
For comparison with DC units(no pulsing)
7.4/14.3VDC VOM/O'scope =Duty Cycle
.5175 = Duty Cycle
.12ma/.5175 = .232ma
Resistance Between Electrodes: 14.3/.232ma =
61.6Kohms
Last reading prior to current regulator kicking in:
1hr 8min: .35ma @ 6.64V(measured at electrodes with
VOM)
(duty cycle affects the
measurements)
For comparison with DC units(no pulsing)
6.64/12.7VDC VOM/O'scope =Duty Cycle
.5228 = Duty Cycle
.35ma/.5228 = .669ma
Resistance Between Electrodes: 12.7/.669ma =
18.97Kohms
Initial measurement after process stopped: Total run time 4hrs.
Pulsed current never got above .38ma
Pulsed voltage = 4.05(VOM) and 7V(O'scope)
For comparison with DC units(no pulsing)
4.05/7VDC = Duty Cycle
.5228 =
.38ma/.5228 = .726ma
7.0/.726ma = 9.64Kohms
16.30/1.97ma = 8.27Kohms
The resistance measurements do not match due to the
current
regulator which is in my circuit. The second
measurement has no
limits therefor would be the most accurate.
Note: Solution was clear, slight bitter taste, no visible
residue in glass,
many bubbles on sides of glass and negative
electrode, some on
positive.
The solution was stirred and allowed to sit for 30min.
Measurements used DC not Pulsed DC
Used a 12v regulator to keep the voltage constant.
Measurement at regulator output: 12.10VDC
All measurements used the Above CS solution.
Current measurement: Turned on power, counted to 5,
read VOM. Not
exact but consistent.
Electrode spacing: 1/2 inch; [email protected]
Resistance: 12.10/1.7ma =7.1Kohms
3/4 inch;
[email protected]
Resistance: 12.10/1.44ma =8.4Kohms
1 inch;
[email protected]
Resistance: 12.10/1.3ma =9.3Kohms
1 1/2 inch;
[email protected]
Resistance: 12.10/1.08ma =11.2Kohms
1 3/4 inch; [email protected]
Resistance: 12.10/1ma = 12.1Kohms
The interesting thing here is that roughly for every 1/4 inch the
electrodes
are move too or from each other the resistance differs about 1000ohms.
Why did I do this? Correlation. If I made a solution with the same
set up as
Ivans but my electrodes were 1/2 inch apart and Ivans was 1 3/4 inch
apart
I could roughly tell if the solution I made was on the same order of
strength
as Ivans. Example: 1 3/4 inch Ivan gets a CS resistance of
20Kohms(5PPM)
for me at 1/2 inch my resistance should
be around
20,000 - (5 X 1000) = 20,000 - 5000 =
15000ohms to get
5PPM
Example2: 1/2 inch I get a CS resistance of
10Kohms(10PPM)
for Ivan at 1 3/4 inch his resistance
should be around
10,000 + (5 X 1000) = 10,000 + 5000 =
15000ohms to get
10PPM
Any Comments/Suggestions?
BillH
--
The silver-list is a moderated forum for discussion of colloidal silver.
To join or quit silver-list or silver-digest send an e-mail message to:
[email protected] -or- [email protected]
with the word subscribe or unsubscribe in the SUBJECT line.
To post, address your message to: [email protected]
List maintainer: Mike Devour <[email protected]>