Addition Item to this post:
I did want to mention that the solution, although had a slight
bitter taste and clear after it was made, has a very bitter taste
now(12hrs)and still clear. 

                                     BillH
-----Original Message-----
From: Hutt William J (Bill) DLPC [mailto:[email protected]]
Sent: Friday, October 29, 1999 6:06 AM
To: [email protected]
Subject: CS>Electrode Spacing





     
Reference:
         http://web.idirect.com~showcase/althealth/cspulse.htm

Setup:  8oz distilled water in clear glass(no starters or salt added)
            1/16 inch wide flat silver electrodes
            2 1/2 wetted length
            Electrode spacing 1 inch
            Pulsed DC generator per above referenced web site
            Pulse rate(frequency) 23.809KHz
            Duty cycle on 54.54% off 45.45%
             water temp around 70 degrees F
            Electrodes wiped after run completed


Run time: 4hrs

                Start:  .12ma @ 7.4V(measured at electrodes with VOM)
                                             (duty cycle affects the
measurements)

                               For comparison with DC units(no pulsing)

                       7.4/14.3VDC VOM/O'scope =Duty Cycle
                                                       .5175 = Duty Cycle
                       .12ma/.5175 = .232ma

                       Resistance Between Electrodes: 14.3/.232ma =
61.6Kohms


Last reading prior to current regulator kicking in:

                       1hr 8min:  .35ma @ 6.64V(measured at electrodes with
VOM)
                                             (duty cycle affects the
measurements)

                               For comparison with DC units(no pulsing)

                       6.64/12.7VDC VOM/O'scope =Duty Cycle
                                                       .5228   = Duty Cycle
                       .35ma/.5228 = .669ma

                       Resistance Between Electrodes: 12.7/.669ma =
18.97Kohms

Initial measurement after process stopped:  Total run time 4hrs.  

                       
                       Pulsed current never got above .38ma
                       Pulsed voltage = 4.05(VOM)  and 7V(O'scope)

                       For comparison with DC units(no pulsing)

                      4.05/7VDC = Duty Cycle
                            .5228   =

                       .38ma/.5228 = .726ma

                       7.0/.726ma    = 9.64Kohms

                       16.30/1.97ma = 8.27Kohms

                        The resistance measurements do not match due to the
current 
                        regulator which is in my circuit.  The second
measurement has no 
                        limits therefor would be the most accurate.


           Note:     Solution was clear, slight bitter taste,  no visible
residue in glass,
                        many bubbles on sides of glass and negative
electrode, some on 
                        positive.

The solution was stirred and allowed to sit for 30min. 

                       Measurements used DC not Pulsed DC
                       Used a 12v regulator to keep the voltage constant.
                       Measurement at regulator output: 12.10VDC
                       All measurements used the Above CS solution.
                       Current measurement:  Turned on power, counted to 5,
                                                          read VOM. Not
exact but consistent.

                       Electrode spacing:  1/2 inch;  [email protected]
 
Resistance: 12.10/1.7ma =7.1Kohms

                                                    3/4 inch;
[email protected]
 
Resistance: 12.10/1.44ma =8.4Kohms

                                                    1 inch;
[email protected]
 
Resistance: 12.10/1.3ma =9.3Kohms

                                                  1 1/2 inch;
[email protected]
 
Resistance: 12.10/1.08ma =11.2Kohms

                                                  1 3/4 inch; [email protected]
 
Resistance: 12.10/1ma = 12.1Kohms



           The interesting thing here is that roughly for every 1/4 inch the
electrodes 
     are move too or from each other the resistance differs about 1000ohms.

     Why did I do this?  Correlation.  If I made a solution with the same
set up as 
      Ivans but my electrodes were 1/2 inch apart and Ivans was 1 3/4 inch
apart 
     I could roughly tell if the solution I made was on the same order of
strength 
     as Ivans.   Example:  1 3/4 inch Ivan gets a CS resistance of
20Kohms(5PPM) 
                                    for me at 1/2 inch my resistance should
be around
                                     20,000 - (5 X 1000) = 20,000 - 5000 =
15000ohms to get
                                    5PPM

                   Example2: 1/2 inch I get a CS resistance of
10Kohms(10PPM) 
                                    for Ivan at 1 3/4 inch his resistance
should be around
                                    10,000 + (5 X 1000) = 10,000 + 5000 =
15000ohms to get
                                    10PPM
                                     

     Any Comments/Suggestions?


                                                                   BillH





--
The silver-list is a moderated forum for discussion of colloidal silver.

To join or quit silver-list or silver-digest send an e-mail message to: 
[email protected]  -or-  [email protected]
with the word subscribe or unsubscribe in the SUBJECT line.

To post, address your message to: [email protected]

List maintainer: Mike Devour <[email protected]>