If you are talking about the Silver Pulser by Sota Instruments (the one approved by Bob Beck), here is some info and spec's.
This is supposed to be very powerful in killing viruses, bacteria and any other foreign organisms in the blood. Probably much more effective if taking CS too. I have built a number of these as well as the Magnetic Pulse Generator, another powerful Baddie Blaster which we can discuss at a later date. Silver Pulser spec's and general usage info: Battery Voltage: 9 Volts DC (Alkaline Battery) Output Voltage at Colloidal Silver Probes: 27 Volts DC, +/- 1 Volt Output Current: 20 milliamps maximum when silver wires are shorted Ionic-Colloid Silver Production: 3 - 5ppm (parts per million) for 20 minutes for 8-16 ounces distilled water. Ionic-Colloid Silver Particle Size: Mostly ionic, with colloidal particles in the range of 0.005 - 0.015 microns when made as directed. Silver Wire Life: Can make approximately 80 gallons of 3 - 5 ppm ionic-colloidal silver per set of silver wires, when made as directed. Output Voltage at Gold Stimulator Probes: 27 Volts (Peak per Cycle, 54 Volts Peak-Peak) Bi-Phasic at ~3.92 Hertz (cycles per second) +/- 1 Hz This conforms to Dr. Beck's specifications exactly. Output Current at Gold Stimulator Probes: ~25 milliamps maximum when probes shorted and control knob on full intensity. You apply the gold probes to your wrist (on either side of the artery) and a few hundred microamps (less than a thousandth of one amp flow thru the blood - not anywhere near enough current to cause damage to your tissues). Treatment time is usually 1/2 hour to 2 hours. Bil ----- Original Message ----- From: Jeffrey A. Madore <[email protected]> To: <[email protected]> Sent: Friday, November 19, 1999 6:52 PM Subject: Re: CS>Re: Chuck/meters > Chuck, > > I'm not familiar with what the "pulser" has for an output (frequency, etc). > It sounds like something more than flat DC. Do you know? I'm just > wondering how well it would meter. > > Jeff > (Two can live as cheaply as one... for half as long.) > > Charles King wrote: > > > On Fri, 19 Nov 1999 12:35:29 -0700, "Katarina Wittich" <[email protected]> > > wrote: > > > > >Now what do you mean when you say "> > > >> If you place it on the milliamp range, in series with one of your silver > > >> electrodes, you will know the current going through your water. > > >I have the bob beck silver pulser and the electrodes are not detacheable -- > > >does in series mean I would have to put the meter between the electrode and > > >the wire that leads to it? I guess I could dismantle it and figure out how > > >to reattatch. Suggestions? > > > > My comments referred to adding a milliamp meter to the simplest of setups. > > That is: 3 battery, 2 clipleads, 2 silver electrodes that are bent to clip on > > the edge of a glass of distilled water. > > > > Anything else will take some simple innovation. > > > > If your device is complete with silver electrodes attached, you'll have to > > leave your device on the bench and use seperate new silver as above. > > Run one clip lead from the meter to one of the electrodes on the Beck device. > > Run one cliplead from the other meter terminal to a new silver electrode on the > > glass. > > Run a third cliplead from the other Beck electrode to the other silver > > electrode on the glass. > > Set the meter to read current, or milliamps (depend on your meter). > > If you draw it out, it's pretty simple. > > Chuck > > if you think education is expensive -- try ignorance. > > > > -- > > The silver-list is a moderated forum for discussion of colloidal silver. > > > > To join or quit silver-list or silver-digest send an e-mail message to: > > [email protected] -or- [email protected] > > with the word subscribe or unsubscribe in the SUBJECT line. > > > > To post, address your message to: [email protected] > > Silver-list archive: http://escribe.com/health/thesilverlist/index.html > > List maintainer: Mike Devour <[email protected]> >

