A note to the CS student. This post by the Coyote is jam-packed with good practical information. While every single little thing may not be exactly correct (I am not suggesting error, only pointing out that new info always changes current belief...)this post is something you should save for future reference. There is more relevant info on CS here than in many lengthy technical writings by others. Take heed. JOH
-----Original Message----- From: Ode Coyote [mailto:[email protected]] Sent: Friday, March 12, 2004 5:53 AM To: [email protected] Subject: Re: CS>Microns, angstroms etc. 1 nanometer = 0.001 micron 1 micron = 10, 000 angstroms 1 angstrom = 0.1 nanometer 1 angstrom = 0.0001 micron Blah blah blah. Google has this cool fuction where you type in 'x' microns to angstroms and it tells you what is what. Fact is, most generator makers [and CS sellers] don't know what size the particles are and will just make something up or copy someone else. Some have the wrong test made. I don't believe SEM or TEM [electron microscopes] results are entirely accurate due to the way they work. Some will intentionally confuse the issue between ions and particles, where if they're not making any particles, they'll use the size of an ion and claim that's it..or even ignore whatever particles they do make and still use the size of an ion or two. If they say anything about an "ion cloud" or TE.... they're making particles. Even ions have several ways to look at what size they are. It's only been recently that I knew what size 'I' made..assuming they were the smallest possible because the CS is clear and free of color. Well, they're not the smallest "possible". [Pretty good though...] ..and the spread can vary some and still be within the range that has no color.... a factor which may have several irrelevancies included such as degrees of oxidation and so on. Frank makes very small particles and his CS is brown, I believe? [He won't say "how" he makes that CS...big secret. And he doesn't sell generators. ] Malvern Particle Sizer results from Frank Keys Collidal Sciences Laboratory: 87% Ionic [single atom minus an electron at 0.000252 microns] http://www.webelements.com/webelements/elements/text/Ag/radii.html 14.3% Particle portion: 54% @ 55.65nm or .0565 microns 45%@ 132.9 nm or .1329 microns Super high HVAC process probably does a better job, but can also make a dangerous product [silver nitrate] if not closley watched and run just right. There's also some controversy on what size is best. Some people say that a range of various sizes [that are small enough to pass through membranes and cell walls] are best because microbes come in different sizes. Heck, sounds good to me. To my way of thinking, If it's too big to get "in", it doesn't need to get "out". [passes right on through] ALL CS "contains" ions and small particles. Even if some are very large, many are very small...so, that "bad" CS will work too. How well determines how much. Since there are no dosing standards that make any sense at all, enough is enough. Since CS at the concentrations commonly sold and made [3 to 20 PPM] is less toxic [silver wise] than the water it's in, too much is nearly impossible. [Some degree of caution as to dose and duration is advisable if it's extremely strong] I think color is still a good rule of thumb. Clear is best. [Virtually any generator can make clear CS up to 5 PPM.] Yellow is Hummm..not bad [pale yellow] to OK [deep yellow] Any other color...red, violet, green...toss it or use it topically Mud...black, brown and cloudy cloudy...including 'other colors' will work. [but if it's really really thick..be a bit careful with dose and duration] Using a timer to determine strength cannot work because water varies a lot and therefore, time, will vary by several minutes or even hours to get to the same point. Just a few degrees difference in water temperature changes time considerably. Using a PPM or other conductivity meter like a PWT is a help, but it's still measuring apples to get oranges and changing an element in the process can throw corrolations between virtually unrelated things, off quite a bit. For example: [from http://www.silver-colloids.com/Reports/cpr19/cpr_19.html] Earthborn Products claiming 100 PPM [Obviously using a meter to get that figure] Conductivity: 164 uS/cm Total Silver Concentration: 0.52 ppm +/- 0.05 ppm Percent Ionic: 100 [This might also be an example of how a high voltage setup can go wrong...but I don't know what process Earthborn used. Why so much conductivity and so little silver when all of it is ionic? ] A generator that uses current controls and a reference voltage drop to reach a shut down point are the most accurate. There's still some inherent variation in particle count and accuracy is still not 100%, but at least they always run the same "way", batch to batch. Ode At 07:36 PM 3/11/2004 -0600, you wrote: >>>> Hi, Can anyone explain the difference between the size of the colloidal silver particles? One company will advertise one way and another company will advertise another way. Apparently the smaller the silver particles, the more beneficial? If this is the case, can anyone say with authority which company sells a generator that produces the smallest particles of colloidal silver? Thank you, Jean Baugh <<<< -- The Silver List is a moderated forum for discussing Colloidal Silver. Instructions for unsubscribing are posted at: http://silverlist.org To post, address your message to: [email protected] Silver List archive: http://escribe.com/health/thesilverlist/index.html Address Off-Topic messages to: [email protected] OT Archive: http://escribe.com/health/silverofftopiclist/index.html List maintainer: Mike Devour

