> > Is anyone sucessfully using the TSV05 (TS) device with the PDP-11 > > (or VAX) emulation?
> Yes. OK, then I must be doing something wrong. > > Here is the SIMH configuration info: > > > > sim> show ts > > TS address=17772520-17772523, no vector > > attached to dka300:[tpc_images.aef]108_AEF_WD_DRIVER_RSX.TPC, > > read only, write enabled, TPC format unlimited capacity > > > > (As an aside, why does it display "no vector", when the physical device (and > > hopefully the emulation) uses a fixed vector of 224?) > > This detail should be resolved before much else will work. Aha, that would make sense. If it doesn't interrupt, RSX will never see the operation completion. > Please supply the configuration file you are using with the > simulator and more precise and useful answers can be provided. Here it is: -------------------------------------------------- ; RSX1986.INI ; ; SIMH initialization file to set up an environment for ; a PDP-11 that will properly run the Flying Disk Systems ; RSX-11M-Plus v3.0 system from 1986 using the values ; from the SYSGEN saved answer file. ; set cpu 11/73 set cpu 2048K set tti 8b set tto 8b ; ; Devices not used in this configuration ; set DZ disabled set RX disabled set TQ disabled ; ; RH controllers (Massbus) ; ; RHA address=17776700-17776753, vector=254 (default) ; set RHA enabled set RHB disabled ; ; Drives on RHA ; set RP0 RM05 set RP1 RM03 ; ; RK11 cartridge disk controllers ; ; RK address=17777400-17777417, vector=220 (default) ; ; Unit 0/1 is an RK05F (fixed) ; Unit 2 is an RK05J (removable) ; set RK enabled ; ; RL11/RLV11 disk cartridge controllers ; ; RL RLV12, address=17774400-17774411, vector=160 (default), 2 units ; set RL0 RL02 set RL1 RL02 set RL2 disabled set RL3 disabled ; ; MSCP disk controllers ; set RQ enabled set RQ address=17772150 set RQ0 enabled ; set RQB enabled set RQB address=17772144 ; Vector is set by software (RSX) ; set RQB vector=170 set RQB1 enabled set RQB2 enabled set RQB3 enabled ; set RQC disabled set RQD disabled ; ; CR11 card reader ; ; CR address=17777160-17777167, vector=230 (default) ; set CR enabled ; ; ; TS11/TU80/TSV05/TK25 magtape controllers ; ; TS address=17772520-17772523, vector=224 (default) ; set TS enabled set TS address=17772520 ; Vector is fixed in hardware at 224 ; ; RXV21 disk controllers ; set RY enabled set RY address=17777170 set RY vector=264 ; ; ; LP/LS/LV11/LA180 line printer ; LPT address=17777514-17777517, vector=200 (default) set LPT enabled set LPT address=17777514 set LPT vector=200 ; ; PC11 paper tape reader/punch ; ; PTR address=17777550-17777553, vector=70 (default) ; PTP address=17777554-17777557, vector=74 (default) ; set PTR enabled set PTP enabled ; ; Because SIMH serial line implementation is not compatible ; with our configuration, do not enable them. ; Likewise, the TU58 is not supported. ; ; Attach our two primary disks ; attach rq1 DKA200:[FRISBIE.SIMH]RSX_RD53_1.DSK attach rq3 DKA200:[FRISBIE.SIMH]RSX_RD53_3.DSK -------------------------------------------------- Thanks, Alan _______________________________________________ Simh mailing list [email protected] http://mailman.trailing-edge.com/mailman/listinfo/simh
