Yes of course, I don't know why I didn't do that. Ok here is my setup. I'm running sipXecs 3.10.2 on a server with 2 NICs. One NIC is for the LAN on for the WAN so I wouldn't need an SBC.
I have tried running the sipviewer program, but I can't seem to figure it out. It requires X of course, and X isn't running on my sipX box, I have a linux box that I'm running from and following the instructions on the page about running it w/o X on the server is not working. I'm not sure what I'm doing wrong on that part. Maybe if someone could point me in the right direction if I'm not doing it right. I'm starting a terminal session from my workstation and typing: # xhost + access control disabled, clients can connect from any host # ssh -Y [EMAIL PROTECTED] then I connect up to the sipX server and try to run the sipviewer command but I keep getting the exception that I don't have an X11 DISPLAY set. So I'm not sure what I'm doing wrong, I've followed the diretions on the site. ----- Original Message ----- From: Tony Graziano <[EMAIL PROTECTED]> Sent: Wed, 9/17/2008 3:21pm To: GovDeals - Jason King <[EMAIL PROTECTED]> ; [email protected] Subject: Re: [sipx-users] Can't make call because of fast timeout Jason, when you post anything it might also help to explain what you are using to connect to your ITSP and what version of sipx you are using. Example: running version 3.10.2 using an ingate for siptrunking with provider ABC OR version 3.11.6 with sipXbridge using provider DEF Posting a call trace (see Dale's email just sent in) tells a great deal about the call, and can point to where it failed. While the snapshot shows how your dialplan and devices are configured inside sipx, so this shows "half of the picture" along with the call trace it can be very helpful indeed. Tony >>> GovDeals - Jason King <[EMAIL PROTECTED]> 9/17/2008 4:00:22 PM >>> Well, then I don't know why I'm getting timeouts on some numbers and successful calls on other numbers. I can all the SIP Trunks FAX line and it answers w/o a problem. I can call my cell phone (even though it goes to the voicemail system of AT&T instead of to my voicemail directly). But I can't call my desk phone here at work. jason ----- Original Message ----- From: Scott Lawrence <[EMAIL PROTECTED]> Sent: Wed, 9/17/2008 2:58pm To: GovDeals - Jason King <[EMAIL PROTECTED]> Cc: sipx-users <[email protected]> Subject: Re: [sipx-users] Can't make call because of fast timeout On Wed, 2008-09-17 at 14:51 -0400, GovDeals - Jason King wrote: > I can't make an outbound call because apparently (according to the SIP > Trunk provider) sipX is giving up on the call before it receives the > signal back from the SIP trunk server. So I need to increase the time > the server waits for a "100 trying" response from the SIP Trunk > server. Where is this setup at? That timer is not configurable. Your problem is not what you (or they) think that it is. Have you measured the time from the INVITE to the 100? Even if the 100 is slow, sipXecs will retransmit when that timer expires, not give up. _______________________________________________ sipx-users mailing list [email protected] List Archive: http://list.sipfoundry.org/archive/sipx-users Unsubscribe: http://list..sipfoundry.org/mailman/listinfo/sipx-users _______________________________________________ sipx-users mailing list [email protected] List Archive: http://list.sipfoundry.org/archive/sipx-users Unsubscribe: http://list.sipfoundry.org/mailman/listinfo/sipx-users _______________________________________________ sipx-users mailing list [email protected] List Archive: http://list.sipfoundry.org/archive/sipx-users Unsubscribe: http://list.sipfoundry.org/mailman/listinfo/sipx-users
