John, Did you try accessing the http by directly connecting the AP to the PC (using cross over adaptor)? Please verify the following. 1. Set the PC IP address (same subnet range) 2. Set the IP and correct GW IP address 3. Set the correct primary port=Ethernet 4. Ping the ISP's DNS ip address 5. browse the web. What kind of CPE devices you are using to associate with AP? If above results are successful, associate using CPE wireless unit and change the preamble to "short" and see the results (by default AP set to "long). If you find no effect, put back to "long".
If still problem exists, please restore the device to the factory default (pressing reset for 20 seconds) and try again the same. Thanks Seeni, SB support -----Original Message----- From: [EMAIL PROTECTED] [mailto:[EMAIL PROTECTED] On Behalf Of John Mooring Sent: Tuesday, June 24, 2003 5:41 AM To: '[EMAIL PROTECTED]' Subject: RE: [smartBridges] non Smartbridges CPE Seeni, First Thank you for actually sounding like you want to help, The rest of these responses just disagree with me. I deployed this AP with just changing its IP address, everything else is factory. I even left it open and easily accessable for the test. I can do everthing but surf the NET. I first thought that this would be a problem with their browser, so I swapped in my laptop, same issue. Actually nothing worked until I put the orinocco equipment back on the tower. Don't missread this, I am not Bitching or complaining, just want some honest answers to get my clients going. John -----Original Message----- From: [EMAIL PROTECTED] [mailto:[EMAIL PROTECTED] Behalf Of Seeni Sent: Monday, June 23, 2003 2:34 PM To: [EMAIL PROTECTED] Subject: RE: [smartBridges] non Smartbridges CPE Hi John, The airpointPRo and airbridge series are 802.11b standard based wireless devices. The additional features and functionality will be varies between the different manufactures products. When you use sB's AP, the port 80 not responding means, could you please give us the detail information of the AP's setup like firmware, configuration etc.. Thanks Seeni, SB support -----Original Message----- From: [EMAIL PROTECTED] [mailto:[EMAIL PROTECTED] On Behalf Of John Mooring Sent: Tuesday, June 24, 2003 1:52 AM To: '[EMAIL PROTECTED]' Subject: [smartBridges] non Smartbridges CPE OK, I have deployed many WET-11 CPE's, work great with orinocco AP's and my home made Linux loaded AP's. When i replaced the Orinoco stuff with Smartbridge AP's all port 80 traffic stops. strange, but true. Airbridges can pass everything, but no other branded CPE can. I thought these radios stayed in the 802.11 b standard, if not let me know. John The PART-15.ORG smartBridges Discussion List To Join: mailto:[EMAIL PROTECTED] (in the body type subscribe smartBridges <yournickname> To Remove: mailto:[EMAIL PROTECTED] (in the body type unsubscribe smartBridges) Archives: http://198.63.203.6 The PART-15.ORG smartBridges Discussion List To Join: mailto:[EMAIL PROTECTED] (in the body type subscribe smartBridges <yournickname> To Remove: mailto:[EMAIL PROTECTED] (in the body type unsubscribe smartBridges) Archives: http://198.63.203.6 The PART-15.ORG smartBridges Discussion List To Join: mailto:[EMAIL PROTECTED] (in the body type subscribe smartBridges <yournickname> To Remove: mailto:[EMAIL PROTECTED] (in the body type unsubscribe smartBridges) Archives: http://198.63.203.6 The PART-15.ORG smartBridges Discussion List To Join: mailto:[EMAIL PROTECTED] (in the body type subscribe smartBridges <yournickname> To Remove: mailto:[EMAIL PROTECTED] (in the body type unsubscribe smartBridges) Archives: http://198.63.203.6
