Alex, In my case, I can tell because when I go to the client's house and hook up my laptop and log into the airbridge, the ESSID has turned to garbage. The blue light on the AB blinks very steady, off and on, off and on (when it's associated it still blinks, but it is very intermittent, on more than off. When it loses it's association it's off and on like clockwork.) This is true across the board when this problem occurs.
Hope this helps. Sam On Tue, 24 Jun 2003, Alex Wong wrote: > Scott, > > When client computer turned on, how do you tell the association is not > there? If the TXRX LED is solid, it is indicating associated. Can check > them out of happen again? Also, do you hardcode the ESSID, or set as > ANY? If it is any, the airBridge can associate to any AP. When the > problem happen, does anybody does the restore to default causing the > ESSID to ANY (unless you have used simpleDeploy for default config). > > If the problem persists, please let us know and I would like you to send > to us directly for analysis. > > Alex > sB Tech Support > > > > > -----Original Message----- > From: [EMAIL PROTECTED] > [mailto:[EMAIL PROTECTED] On Behalf Of shoffman > Sent: Tuesday, June 24, 2003 12:49 AM > To: '[EMAIL PROTECTED]' > Subject: Fwd: RE: [smartBridges] Weird Characters in ESSID and Loss > ofassociation > > > > Alex, > > Agreed on power supply, especially in light of the Onion report. We > have > 50 installed from that batch you guys are dealing with. We haven't had > any "total" dead, but one may have a heat problem. (replacing it > today... stays good for about 60 minutes, then looses association. > Restart, nothing. Turn it down.. wait about 10 minutes.. turn-up, > bang, > back on air.. for about 1 hour or so... (some times shorter). We > will > do some in house checking before we attempt an RMA...) > > But back to the original, We have done our best (except putting a UPS or > > larger power supply on the power shot)to clean up the power, but given > it > is a rural install, power may not be totally clean. But what leads us > to our theory is that this only happened when the client computer was > turned off at night (or during the day). The AB was never pwoered off, > > but when clients computer turned on.. Association was not there. We go > out and reset the jibberish in the ESSID, and walla, back up and happy. > > Again, another point leading us to believe our theory is that since we > started the pining (3 weeks ago) we have never heard from client again > (i.e. its staying solid...) So... go figure. > > Scott > > > -----Original Message----- > From: "Alex Wong" <[EMAIL PROTECTED]> > To: <[EMAIL PROTECTED]> > Date: Tue, 24 Jun 2003 00:17:51 +0800 > Subject: RE: [smartBridges] Weird Characters in ESSID and Loss of > association > > It could be the noisy power source or some spike that cause the memory > to corrupt. Check if there is proper grounding and clean power supply. > > Alex > sB Tech Support > > > > > -----Original Message----- > From: [EMAIL PROTECTED] > [mailto:[EMAIL PROTECTED] On Behalf Of Sam > Sent: Monday, June 23, 2003 3:04 PM > To: '[EMAIL PROTECTED]' > Subject: RE: [smartBridges] Weird Characters in ESSID and Loss of > association > > > No, this isn't what happened. There is no software on these computers > for > the person to be able to log into the airbridge with. I have to take my > laptop to them and login to the AB and reassociate it myself. > > Can anyone at SB shed light on this? > > Thanks > Sam > > > On Mon, 23 > Jun 2003, phantam wrote: > > > I HAVE seen this whenever I do a remote essid change and it fails, > > maybe the text isn't being sent properly but in this case it messes up > > > quite often. Once it messed up and I could swear it was screwed up but > > > they reset it and it associated properly I don't know if it just was > > sent properly but not associated or it's a messed up command that the > > unit has to be rebooted after a essid change and it doesn't do it > > properly. > > > > What could this be seeni? > > > > Chris > > > > -----Original Message----- > > From: George [mailto:[EMAIL PROTECTED] > > Sent: Monday, June 23, 2003 1:32 AM > > To: [EMAIL PROTECTED] > > > > One thing I don't do, is install any utility that allows them to get > > involved in any way with the radio gear. The less they know the better > > > we all are. Of course we always retain ownership of the radio. I even > > do that with the gateway router in most cases, even though they > do > > buy that from me. > > In most cases all we have to do is tell them to reboot their pc, > gateway > > router, or radio when they stop working. > > George > > > > ----- Original Message ----- > > From: "Tom Andrews" <[EMAIL PROTECTED]> > > To: <[EMAIL PROTECTED]> > > Sent: Sunday, June 22, 2003 9:28 PM > > Subject: Re: [smartBridges] Weird Characters in ESSID and Loss of > > association > > > > > > > Have you seen an AP with the ESSID of ZUCimkXZ while doing any > > > installs or war driving? Do these customers who had issues have > > > access to > > simpleMonitor > > > and if so are they the type who might have played with the radio in > > > an attempt to "fix" the connection? > > > > > > I have one who thinks they know more about our system than we do and > > > > they are always causing me issues by screwing around with all their > > > settings. They are not using anything from smartBridge, but another > > > radio I no > > longer > > > use. I guess I don't charge enough to go clean up their messes when > > > they > > get > > > good and drunk. > > > > > > Tom > > > ----- Original Message ----- > > > From: "Sam" <[EMAIL PROTECTED]> > > > To: <[EMAIL PROTECTED]> > > > Sent: Sunday, June 22, 2003 23:28 > > > Subject: [smartBridges] Weird Characters in ESSID and Loss of > association > > > > > > > > > > Tonight I went to two of my customer's homes to re-associate their > > > > > airbridges. When I got there the ESSID had changed from logan-wt > > > > to something like ZUCimkXZ and the BSSID was all zeros. Earlier > > > > this > > weekend > > > > another customer with an airbridge outdoor had the same thing > > > > happen. > > His > > > > ESSID changed from logan-wt to some jumble of letters. > > > > > > > > Got any idea what is causing this to happen? There are about 30 > > > > people > > on > > > > that AP (logan-wt). All three of these people are on the logan-wt > > > > AP. As far as I know they are the only three that lost > > > > association, but this is the third time in a month or so that it's > > > > > happened. Are these defective Airbridges? Their RSSI is > 50% and > > > > the Link quality is close to 80%. > > They > > > > are at most six miles from the AP, and one of them is only a > > > > couple of miles away from the AP. > > > > > > > > Should I get an rma for these or do you think there is something > > > > else causing this? They are all using 1.50 of the firmware, though > > > > > I did have the man with the outdoor airbridge backrev to 1.43 to > > > > see if that will help. > > > > > > > > Thanks > > > > Sam Morris, Owner > > > > Loganet Internet Service > > > > Logan IA > > > > > > > > The PART-15.ORG smartBridges Discussion List > > > > To Join: mailto:[EMAIL PROTECTED] (in the body type subscribe > > > smartBridges <yournickname> > > > > To Remove: mailto:[EMAIL PROTECTED] (in the body type > > > > unsubscribe > > > smartBridges) > > > > Archives: http://198.63.203.6 > > > > > > > > > > > > > The PART-15.ORG smartBridges Discussion List > > > To Join: mailto:[EMAIL PROTECTED] (in the body type subscribe > > smartBridges <yournickname> > > > To Remove: mailto:[EMAIL PROTECTED] (in the body type unsubscribe > > smartBridges) > > > Archives: http://198.63.203.6 > > > > > > > The PART-15.ORG smartBridges Discussion List > > To Join: mailto:[EMAIL PROTECTED] (in the body type subscribe > > smartBridges <yournickname> To Remove: mailto:[EMAIL PROTECTED] (in > > > the body type unsubscribe > > smartBridges) > > Archives: http://198.63.203.6 > > > > The PART-15.ORG smartBridges Discussion List > To Join: mailto:[EMAIL PROTECTED] (in the body type subscribe > smartBridges <yournickname> To Remove: mailto:[EMAIL PROTECTED] (in > the body type unsubscribe smartBridges) > Archives: http://198.63.203.6 > > The PART-15.ORG smartBridges Discussion List > To Join: mailto:[EMAIL PROTECTED] (in the body type subscribe > smartBridges <yournickname> To Remove: mailto:[EMAIL PROTECTED] (in > the body type unsubscribe > smartBridges) > Archives: http://198.63.203.6 > > The PART-15.ORG smartBridges Discussion List > To Join: mailto:[EMAIL PROTECTED] (in the body type subscribe > smartBridges <yournickname> To Remove: mailto:[EMAIL PROTECTED] (in > the body type unsubscribe smartBridges) > Archives: http://198.63.203.6 > > The PART-15.ORG smartBridges Discussion List > To Join: mailto:[EMAIL PROTECTED] (in the body type subscribe smartBridges > <yournickname> > To Remove: mailto:[EMAIL PROTECTED] (in the body type unsubscribe smartBridges) > Archives: http://198.63.203.6 > The PART-15.ORG smartBridges Discussion List To Join: mailto:[EMAIL PROTECTED] (in the body type subscribe smartBridges <yournickname> To Remove: mailto:[EMAIL PROTECTED] (in the body type unsubscribe smartBridges) Archives: http://198.63.203.6
