Electro-Comm: Comtelco BSAL2400-12-190, Cost $150
Page 6 of their latest catalog which you can download at www.electro-comm.com. Bobby ----- Original Message ----- From: "Rudolph Worrell" <[EMAIL PROTECTED]> To: <[EMAIL PROTECTED]> Sent: Saturday, September 27, 2003 7:26 PM Subject: RE: [smartBridges] RSSI > where can I find these? > > -----Original Message----- > From: [EMAIL PROTECTED] > [mailto:[EMAIL PROTECTED] Behalf Of Bobby Bounds > Sent: Saturday, September 27, 2003 7:39 PM > To: [EMAIL PROTECTED] > Subject: Re: [smartBridges] RSSI > > > Use two, 180 deg. sector antennas ($150 each). One radio per antenna. The > amp is fine (you may need two). Don't use a splitter. Trash the omni. > > > ----- Original Message ----- > From: "Rudolph Worrell" <[EMAIL PROTECTED]> > To: <[EMAIL PROTECTED]> > Sent: Saturday, September 27, 2003 6:26 PM > Subject: RE: [smartBridges] RSSI > > > > I am using a 12dbi omni at the head end. What do you suggest. I thought > > about a 500Mw amp>>>4way splitter>>>4 90degree directional for 360 > coverage. > > What do you think? > > > > -----Original Message----- > > From: [EMAIL PROTECTED] > > [mailto:[EMAIL PROTECTED] Behalf Of Bobby Bounds > > Sent: Saturday, September 27, 2003 5:44 PM > > To: [EMAIL PROTECTED] > > Subject: Re: [smartBridges] RSSI > > > > > > FWIW, the 24 grids are extremely sensitive to alignment at that distance. > > The tiniest azimuth and/or elevation change will have a big effect. You > > should be booming in using that grid (85% or better). Hope you are not > using > > an Omni at the head end, they suck for longer distances. You need RSSI up > > past 75%....also watch the link for ten minutes on the link quality graph > > and check for it dropping off. Also, those grids can be assembled > > incorrectly if you're not careful, so you may want to double check that. > > > > > > > > > > > > ----- Original Message ----- > > From: "Rudolph Worrell" <[EMAIL PROTECTED]> > > To: <[EMAIL PROTECTED]> > > Sent: Saturday, September 27, 2003 3:34 PM > > Subject: [smartBridges] RSSI > > > > > > > Hello everyone, > > > > > > What is the minimum RSSI and Link Quality needed to associate with an > AP. > > > > > > I have a client 10mi away with an RSSI of 47% to 50% and I cannot get > them > > > to associate on a consistent basis. If I get it and reset the APPO it > > loses > > > it and takes forever to get it back. I have another client only 6 miles > > > away with Near LOS and gets 37% RSSI with 65% Link Quality but no > > > association whatever. The 1st client has a 24 dbi grid and the second > has > > a > > > 19 dbi grid. > > > > > > I have a 500Mw on the main AP. > > > > > > Any suggestion or info I am missing? > > > > > > Rudy > > > > > > ----------ANNOUNCEMENT---------- > > > Don't forget to register for WISPCON IV > > > http://www.wispcon.info/us/wispcon-iv/wispcon-iv.htm > > > > > > The PART-15.ORG smartBridges Discussion List > > > To Join: mailto:[EMAIL PROTECTED] (in the body type subscribe > > smartBridges <yournickname> > > > To Remove: mailto:[EMAIL PROTECTED] (in the body type unsubscribe > > smartBridges) > > > Archives: http://archives.part-15.org > > > > > > > > > ----------ANNOUNCEMENT---------- > > Don't forget to register for WISPCON IV > > http://www.wispcon.info/us/wispcon-iv/wispcon-iv.htm > > > > The PART-15.ORG smartBridges Discussion List > > To Join: mailto:[EMAIL PROTECTED] (in the body type subscribe > > smartBridges <yournickname> > > To Remove: mailto:[EMAIL PROTECTED] (in the body type unsubscribe > > smartBridges) > > Archives: http://archives.part-15.org > > > > ----------ANNOUNCEMENT---------- > > Don't forget to register for WISPCON IV > > http://www.wispcon.info/us/wispcon-iv/wispcon-iv.htm > > > > The PART-15.ORG smartBridges Discussion List > > To Join: mailto:[EMAIL PROTECTED] (in the body type subscribe > smartBridges <yournickname> > > To Remove: mailto:[EMAIL PROTECTED] (in the body type unsubscribe > smartBridges) > > Archives: http://archives.part-15.org > > > > > ----------ANNOUNCEMENT---------- > Don't forget to register for WISPCON IV > http://www.wispcon.info/us/wispcon-iv/wispcon-iv.htm > > The PART-15.ORG smartBridges Discussion List > To Join: mailto:[EMAIL PROTECTED] (in the body type subscribe > smartBridges <yournickname> > To Remove: mailto:[EMAIL PROTECTED] (in the body type unsubscribe > smartBridges) > Archives: http://archives.part-15.org > > ----------ANNOUNCEMENT---------- > Don't forget to register for WISPCON IV > http://www.wispcon.info/us/wispcon-iv/wispcon-iv.htm > > The PART-15.ORG smartBridges Discussion List > To Join: mailto:[EMAIL PROTECTED] (in the body type subscribe smartBridges <yournickname> > To Remove: mailto:[EMAIL PROTECTED] (in the body type unsubscribe smartBridges) > Archives: http://archives.part-15.org > ----------ANNOUNCEMENT---------- Don't forget to register for WISPCON IV http://www.wispcon.info/us/wispcon-iv/wispcon-iv.htm The PART-15.ORG smartBridges Discussion List To Join: mailto:[EMAIL PROTECTED] (in the body type subscribe smartBridges <yournickname> To Remove: mailto:[EMAIL PROTECTED] (in the body type unsubscribe smartBridges) Archives: http://archives.part-15.org
