I check all the boxes (1 through 11) and enable auto fallback. On the client end I set them all to one or two.
On Fri, 17 Oct 2003, Breiland, Derek wrote: > Just curious if what speed you are letting the radios run at? I have turned > off auto select fall back on both the APO's and the clients (AirBridge) in > basic settings. I only check the 1Mps and 2Mps boxes in the basic settings > on the APO. I am setting all of the clients to connect at 2Mps which is > plenty fast - no degradation with that. This has increased the stability of > all links considerably especially when a client is doing something very > bandwidth intensive. > > -----Original Message----- > From: Sam [mailto:[EMAIL PROTECTED] > Sent: Friday, October 17, 2003 2:07 PM > To: [EMAIL PROTECTED] > Subject: Re: [smartBridges] Length out of range numbers > > I have over 30 customers each on two APPOs which seem to handle it just > fine (that is, when the APPO is still running.) The only problem I have > seen is sometimes the APPO just stops, and the blue light starts blinking > steadily off and on, off and on, and I'm unable to log into the device any > further, even through the wire. But I've gotten to the point when that > happens I put up another one. (Tired of troubleshooting them.) The only > problem is reassociating everyone (Not all of my customers have the > roaming option.) > > Anyhow, they seem to handle at least 30 users without problem. > > Sam > > On Fri, 17 Oct 2003, > Blazen Wireless wrote: > > > the APPO goes into a D-link switch with another APPO and a canopy radio > > which is set to 10 1/2 duplex. The canopy is flawless and has no errors at > > all! its always the APPO that comes back with errors? I see dingle defer > > errors and an occasion CTS error I tried swapping the switch to a 10 meg > hub > > and it made no difference I just think the APPOs cant handle the load of 9 > > customers on all the time it just craps out.. > > > > Each customer that I add on seems to make the system ore and more > unstable! > > I was under the impression these radios would handle a lot of clients > radios > > talking to it but I guess now. I am going to have to go with something > > else.. > > > > > > The XO is way out of range, I have all the bandwidth and access control I > > need at the NOC no need for it in the radio.. > > > > ----- Original Message ----- > > From: "Lars Gaarden" <[EMAIL PROTECTED]> > > To: <[EMAIL PROTECTED]> > > Sent: Friday, October 17, 2003 11:22 AM > > Subject: Re: [smartBridges] Length out of range numbers > > > > > > Blazen Wireless wrote: > > > > > What exactly is controlling this number is this > > > good or bad? I assume bad I rebooted the appo > > > yesterday and am seeing these since about 12pm > > > PT yesterday to the tune of about 23,500? > > > > LengthOutOfRangeRx is one of the ethernet counters. > > > > According to Cisco, the meaning is: > > > > "Length out of range > > Incremented for each frame received where the 802.3 > > length field in the packet did not match the number > > of bytes actually received." > > > > What is connected to the aPPO on the ethernet side? > > Do you see any other ethernet error counters that are > > unusually high? (CRC, False carrier, Under/Oversize) > > > > > > > ----------ANNOUNCEMENT---------- > Don't forget to register for WISPCON IV > http://www.wispcon.info/us/wispcon-iv/wispcon-iv.htm > > The PART-15.ORG smartBridges Discussion List > To Join: mailto:[EMAIL PROTECTED] (in the body type subscribe > smartBridges <yournickname> > To Remove: mailto:[EMAIL PROTECTED] (in the body type unsubscribe > smartBridges) > Archives: http://archives.part-15.org > ----------ANNOUNCEMENT---------- > Don't forget to register for WISPCON IV > http://www.wispcon.info/us/wispcon-iv/wispcon-iv.htm > > The PART-15.ORG smartBridges Discussion List > To Join: mailto:[EMAIL PROTECTED] (in the body type subscribe smartBridges > <yournickname> > To Remove: mailto:[EMAIL PROTECTED] (in the body type unsubscribe smartBridges) > Archives: http://archives.part-15.org > ----------ANNOUNCEMENT---------- Don't forget to register for WISPCON IV http://www.wispcon.info/us/wispcon-iv/wispcon-iv.htm The PART-15.ORG smartBridges Discussion List To Join: mailto:[EMAIL PROTECTED] (in the body type subscribe smartBridges <yournickname> To Remove: mailto:[EMAIL PROTECTED] (in the body type unsubscribe smartBridges) Archives: http://archives.part-15.org
