Oil Fired Boiler? The ignition circuit creates loads of noise. If there is a fault with it then that noise may be crapping on the radio circuit. A supressor on the boiler maybe required. However once the boiler is fired up, it should work OK again. The thermostat may be causing it to come on and off. However your log looked like it was switching on and off every couple of seconds. If the boiler has trouble ignighting then you could have several seconds of noise followed by a minute or 2 no problems, then noise again.
Wayland. ----- Original Message ----- From: "The Wirefree Network" <[EMAIL PROTECTED]> To: <[EMAIL PROTECTED]> Cc: "'Vasu (sB Tech Team)'" <[EMAIL PROTECTED]> Sent: Wednesday, November 26, 2003 1:43 AM Subject: RE: [smartBridges] Puzzle?? Need help. I really don't know. Notice (the attachment) that the first night I installed him (besides the time frame that he unplugged it) his RSSI/LQ were fine all night. He then went out of town. Ever since he left, from 10pm - 8am, his connection goes to CRAPOLA! Notice that Monday night's signal was much worse (during same time frame) then Sunday night's. FYI...it was about 5 degrees colder last night then Sunday night. Any ideas?? Sully > -----Original Message----- > From: [EMAIL PROTECTED] [mailto:[EMAIL PROTECTED] > 15.org] On Behalf Of Wayland Sothcott > Sent: Tuesday, November 25, 2003 3:36 PM > To: [EMAIL PROTECTED] > Cc: 'Vasu (sB Tech Team)' > Subject: Re: [smartBridges] Puzzle?? Need help. > > power supply problem? > > ----- Original Message ----- > From: "The Wirefree Network" <[EMAIL PROTECTED]> > To: <[EMAIL PROTECTED]> > Cc: "'Vasu (sB Tech Team)'" <[EMAIL PROTECTED]> > Sent: Tuesday, November 25, 2003 4:01 PM > Subject: [smartBridges] Puzzle?? Need help. > > > Can anyone put this puzzle together?? > > I had a new client ("CLIENT 1") 2 weeks ago in "AREA A" off of "TOWER 3". > This client had 100% RSSI and 91%LQ...during the day. Sometime between > 7pm > and 10pm, his LQ would completely CRAP OUT. His aB became totally > unusable > between then and 9am. I did some sniffing and saw that his neighbor had > an > internal network on our channel. So, I swapped this client over to "TOWER > 2", with no further issues. > > I have a new client ("CLIENT 2") (2 days now) in "AREA B" off of "TOWER > 3". > During the day, he is at 100% RSSI and 93% LQ. From 10:00 pm till 8:00 > am, > his LQ goes down to zero and completely knocks his unit off line. Same > exact symptoms as "Client 1" 2 weeks ago. > > FACTS > 1. I did some sniffing, and cant find any interference (channel wise) near > this "Client 2". > 2. AREA B is in a completely different area than AREA A (separated by > miles > and huge hill). > 3. There are other "old" clients (months old) within 2 blocks of "Client > 2" > off of same "Tower 3" with no problems with LQ. > 4. The old clients and new clients are on different firmware versions > (don't > know which right now). > 5. LOS from "Client 2" to "Tower 3" is PERFECT. Distance is only 3/4 mile > with slightly lower elevation than tower (but within RF path). > 6. DON'T FORGET...this is only a problem from 10pm to 8am. > 9. Plz look at attached picture for the ugliness! > > Any ideas? > > Sully > > > The PART-15.ORG smartBridges Discussion List > To Join: mailto:[EMAIL PROTECTED] (in the body type subscribe > smartBridges <yournickname> > To Remove: mailto:[EMAIL PROTECTED] (in the body type unsubscribe > smartBridges) > Archives: http://archives.part-15.org The PART-15.ORG smartBridges Discussion List To Join: mailto:[EMAIL PROTECTED] (in the body type subscribe smartBridges <yournickname> To Remove: mailto:[EMAIL PROTECTED] (in the body type unsubscribe smartBridges) Archives: http://archives.part-15.org
