--
NEU: FreePhone - 0ct/min Handyspartarif mit Geld-zurück-Garantie!
Jetzt informieren: http://www.gmx.net/de/go/freephone
smartctl 5.42 2011-10-11 r3440 [x86_64-linux-2.6.39.4-1000hz] (local build)
Copyright (C) 2002-11 by Bruce Allen, http://smartmontools.sourceforge.net
=== START OF INFORMATION SECTION ===
Device Model: ST380012ACE
Serial Number: 5JVGL4QR
Firmware Version: 9.51
User Capacity: 80.026.361.856 bytes [80,0 GB]
Sector Size: 512 bytes logical/physical
Device is: Not in smartctl database [for details use: -P showall]
ATA Version is: 6
ATA Standard is: ATA/ATAPI-6 T13 1410D revision 2
Local Time is: Sun Oct 16 21:38:11 2011 CEST
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED
General SMART Values:
Offline data collection status: (0x82) Offline data collection activity
was completed without error.
Auto Offline Data Collection: Enabled.
Self-test execution status: ( 0) The previous self-test routine completed
without error or no self-test has ever
been run.
Total time to complete Offline
data collection: (15556) seconds.
Offline data collection
capabilities: (0x5b) SMART execute Offline immediate.
Auto Offline data collection on/off
support.
Suspend Offline collection upon new
command.
Offline surface scan supported.
Self-test supported.
No Conveyance Self-test supported.
Selective Self-test supported.
SMART capabilities: (0x0003) Saves SMART data before entering
power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
General Purpose Logging supported.
Short self-test routine
recommended polling time: ( 1) minutes.
Extended self-test routine
recommended polling time: ( 58) minutes.
SMART Attributes Data Structure revision number: 10
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE
1 Raw_Read_Error_Rate POSR-- 065 058 006 - 129917742
3 Spin_Up_Time PO---- 098 097 000 - 0
4 Start_Stop_Count -O--CK 100 100 020 - 329
5 Reallocated_Sector_Ct PO--CK 100 100 036 - 0
7 Seek_Error_Rate POSR-- 072 060 030 - 14822307
9 Power_On_Hours -O--CK 083 083 000 - 15080
10 Spin_Retry_Count PO--C- 100 100 097 - 0
12 Power_Cycle_Count -O--CK 099 099 020 - 1378
194 Temperature_Celsius -O---K 036 053 000 - 36
195 Hardware_ECC_Recovered -O-RC- 065 058 000 - 129917742
197 Current_Pending_Sector -O--C- 100 100 000 - 0
198 Offline_Uncorrectable ----C- 100 100 000 - 0
199 UDMA_CRC_Error_Count -OSRCK 200 199 000 - 2
200 Multi_Zone_Error_Rate ------ 100 253 000 - 0
202 Data_Address_Mark_Errs -O--CK 100 253 000 - 0
||||||_ K auto-keep
|||||__ C event count
||||___ R error rate
|||____ S speed/performance
||_____ O updated online
|______ P prefailure warning
General Purpose Log Directory Version 1
SMART Log Directory Version 1 [multi-sector log support]
GP/S Log at address 0x00 has 1 sectors [Log Directory]
GP/S Log at address 0x01 has 1 sectors [Summary SMART error log]
GP/S Log at address 0x02 has 5 sectors [Comprehensive SMART error log]
GP/S Log at address 0x03 has 5 sectors [Ext. Comprehensive SMART error log]
GP/S Log at address 0x06 has 1 sectors [SMART self-test log]
GP/S Log at address 0x07 has 1 sectors [Extended self-test log]
GP/S Log at address 0x09 has 1 sectors [Selective self-test log]
GP/S Log at address 0x20 has 1 sectors [Streaming performance log]
GP/S Log at address 0x21 has 1 sectors [Write stream error log]
GP/S Log at address 0x22 has 1 sectors [Read stream error log]
GP/S Log at address 0x23 has 1 sectors [Delayed sector log]
GP/S Log at address 0x80 has 16 sectors [Host vendor specific log]
GP/S Log at address 0x81 has 16 sectors [Host vendor specific log]
GP/S Log at address 0x82 has 16 sectors [Host vendor specific log]
GP/S Log at address 0x83 has 16 sectors [Host vendor specific log]
GP/S Log at address 0x84 has 16 sectors [Host vendor specific log]
GP/S Log at address 0x85 has 16 sectors [Host vendor specific log]
GP/S Log at address 0x86 has 16 sectors [Host vendor specific log]
GP/S Log at address 0x87 has 16 sectors [Host vendor specific log]
GP/S Log at address 0x88 has 16 sectors [Host vendor specific log]
GP/S Log at address 0x89 has 16 sectors [Host vendor specific log]
GP/S Log at address 0x8a has 16 sectors [Host vendor specific log]
GP/S Log at address 0x8b has 16 sectors [Host vendor specific log]
GP/S Log at address 0x8c has 16 sectors [Host vendor specific log]
GP/S Log at address 0x8d has 16 sectors [Host vendor specific log]
GP/S Log at address 0x8e has 16 sectors [Host vendor specific log]
GP/S Log at address 0x8f has 16 sectors [Host vendor specific log]
GP/S Log at address 0x90 has 16 sectors [Host vendor specific log]
GP/S Log at address 0x91 has 16 sectors [Host vendor specific log]
GP/S Log at address 0x92 has 16 sectors [Host vendor specific log]
GP/S Log at address 0x93 has 16 sectors [Host vendor specific log]
GP/S Log at address 0x94 has 16 sectors [Host vendor specific log]
GP/S Log at address 0x95 has 16 sectors [Host vendor specific log]
GP/S Log at address 0x96 has 16 sectors [Host vendor specific log]
GP/S Log at address 0x97 has 16 sectors [Host vendor specific log]
GP/S Log at address 0x98 has 16 sectors [Host vendor specific log]
GP/S Log at address 0x99 has 16 sectors [Host vendor specific log]
GP/S Log at address 0x9a has 16 sectors [Host vendor specific log]
GP/S Log at address 0x9b has 16 sectors [Host vendor specific log]
GP/S Log at address 0x9c has 16 sectors [Host vendor specific log]
GP/S Log at address 0x9d has 16 sectors [Host vendor specific log]
GP/S Log at address 0x9e has 16 sectors [Host vendor specific log]
GP/S Log at address 0x9f has 16 sectors [Host vendor specific log]
GP/S Log at address 0xa0 has 1 sectors [Device vendor specific log]
GP/S Log at address 0xa1 has 20 sectors [Device vendor specific log]
GP/S Log at address 0xa2 has 101 sectors [Device vendor specific log]
GP/S Log at address 0xa8 has 20 sectors [Device vendor specific log]
GP/S Log at address 0xa9 has 1 sectors [Device vendor specific log]
GP Log at address 0xff has 24064 sectors [Reserved]
SMART Extended Comprehensive Error Log Version: 1 (5 sectors)
Device Error Count: 8
CR = Command Register
FEATR = Features Register
COUNT = Count (was: Sector Count) Register
LBA_48 = Upper bytes of LBA High/Mid/Low Registers ] ATA-8
LH = LBA High (was: Cylinder High) Register ] LBA
LM = LBA Mid (was: Cylinder Low) Register ] Register
LL = LBA Low (was: Sector Number) Register ]
DV = Device (was: Device/Head) Register
DC = Device Control Register
ER = Error register
ST = Status register
Powered_Up_Time is measured from power on, and printed as
DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes,
SS=sec, and sss=millisec. It "wraps" after 49.710 days.
Error 8 [7] occurred at disk power-on lifetime: 3006 hours (125 days + 6 hours)
When the command that caused the error occurred, the device was active or
idle.
After command completion occurred, registers were:
ER -- ST COUNT LBA_48 LH LM LL DV DC
-- -- -- == -- == == == -- -- -- -- --
10 -- 51 00 01 00 00 00 00 00 00 e9 00
Commands leading to the command that caused the error were:
CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name
-- == -- == -- == == == -- -- -- -- -- --------------- --------------------
37 00 00 01 01 00 09 f0 00 50 6e e9 00 00:00:22.533 SET MAX ADDRESS EXT
27 00 00 00 00 00 09 f0 00 50 6e e0 00 00:00:22.531 READ NATIVE MAX
ADDRESS EXT
37 00 00 00 00 00 09 f0 00 50 6e e9 00 00:00:22.531 SET MAX ADDRESS EXT
27 00 00 00 01 00 09 f0 00 50 6e e0 00 00:00:20.129 READ NATIVE MAX
ADDRESS EXT
37 00 00 01 01 00 09 f0 00 50 6e e9 00 00:00:19.114 SET MAX ADDRESS EXT
Error 7 [6] occurred at disk power-on lifetime: 1080 hours (45 days + 0 hours)
When the command that caused the error occurred, the device was active or
idle.
After command completion occurred, registers were:
ER -- ST COUNT LBA_48 LH LM LL DV DC
-- -- -- == -- == == == -- -- -- -- --
84 -- 51 00 01 00 00 00 00 00 00 f0 00 Error: ICRC, ABRT 1 sectors at LBA =
0x00000000 = 0
Commands leading to the command that caused the error were:
CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name
-- == -- == -- == == == -- -- -- -- -- --------------- --------------------
25 00 00 00 01 00 00 00 00 00 00 f0 00 00:01:31.791 READ DMA EXT
b0 00 da 01 00 00 00 4f 00 c2 00 f0 00 00:01:30.651 SMART RETURN STATUS
91 00 00 00 3f 00 0f 00 00 00 00 ff 00 00:01:23.687 INITIALIZE DEVICE
PARAMETERS [OBS-6]
c6 00 00 00 10 00 00 00 00 00 00 f0 00 00:01:17.812 SET MULTIPLE MODE
91 00 00 00 3f 00 0f 00 00 00 00 ff 00 00:01:17.595 INITIALIZE DEVICE
PARAMETERS [OBS-6]
Error 6 [5] occurred at disk power-on lifetime: 1080 hours (45 days + 0 hours)
When the command that caused the error occurred, the device was active or
idle.
After command completion occurred, registers were:
ER -- ST COUNT LBA_48 LH LM LL DV DC
-- -- -- == -- == == == -- -- -- -- --
84 -- 51 00 01 00 00 00 00 00 00 f0 00 Error: ICRC, ABRT 1 sectors at LBA =
0x00000000 = 0
Commands leading to the command that caused the error were:
CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name
-- == -- == -- == == == -- -- -- -- -- --------------- --------------------
25 00 00 00 01 00 00 00 00 00 00 f0 00 00:01:00.502 READ DMA EXT
c6 00 00 00 10 00 00 00 00 00 00 f0 00 00:01:00.502 SET MULTIPLE MODE
91 00 00 00 3f 00 0f 00 00 00 00 ff 00 00:01:00.502 INITIALIZE DEVICE
PARAMETERS [OBS-6]
10 00 00 01 00 00 00 00 00 00 00 f0 00 00:01:00.502 RECALIBRATE [OBS-4]
00 00 00 00 01 00 00 00 00 00 00 00 00 00:01:00.188 NOP [Abort queued
commands]
Error 5 [4] occurred at disk power-on lifetime: 1080 hours (45 days + 0 hours)
When the command that caused the error occurred, the device was active or
idle.
After command completion occurred, registers were:
ER -- ST COUNT LBA_48 LH LM LL DV DC
-- -- -- == -- == == == -- -- -- -- --
84 -- 51 00 01 00 00 00 00 00 00 f0 00 Error: ICRC, ABRT 1 sectors at LBA =
0x00000000 = 0
Commands leading to the command that caused the error were:
CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name
-- == -- == -- == == == -- -- -- -- -- --------------- --------------------
25 00 00 00 01 00 00 00 00 00 00 f0 00 00:01:00.502 READ DMA EXT
c6 00 00 00 10 00 00 00 00 00 00 f0 00 00:01:00.502 SET MULTIPLE MODE
91 00 00 00 3f 00 0f 00 00 00 00 ff 00 00:01:00.502 INITIALIZE DEVICE
PARAMETERS [OBS-6]
10 00 00 01 00 00 00 00 00 00 00 f0 00 00:01:00.502 RECALIBRATE [OBS-4]
00 00 00 00 01 00 00 00 00 00 00 00 00 00:01:00.188 NOP [Abort queued
commands]
Error 4 [3] occurred at disk power-on lifetime: 1080 hours (45 days + 0 hours)
When the command that caused the error occurred, the device was active or
idle.
After command completion occurred, registers were:
ER -- ST COUNT LBA_48 LH LM LL DV DC
-- -- -- == -- == == == -- -- -- -- --
84 -- 51 00 01 00 00 00 00 00 00 f0 00 Error: ICRC, ABRT 1 sectors at LBA =
0x00000000 = 0
Commands leading to the command that caused the error were:
CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name
-- == -- == -- == == == -- -- -- -- -- --------------- --------------------
25 00 00 00 01 00 00 00 00 00 00 f0 00 00:01:00.502 READ DMA EXT
c6 00 00 00 10 00 00 00 00 00 00 f0 00 00:01:00.502 SET MULTIPLE MODE
91 00 00 00 3f 00 0f 00 00 00 00 ff 00 00:01:00.502 INITIALIZE DEVICE
PARAMETERS [OBS-6]
10 00 00 01 00 00 00 00 00 00 00 f0 00 00:01:00.502 RECALIBRATE [OBS-4]
00 00 00 00 01 00 00 00 00 00 00 00 00 00:01:00.188 NOP [Abort queued
commands]
Error 3 [2] occurred at disk power-on lifetime: 1080 hours (45 days + 0 hours)
When the command that caused the error occurred, the device was active or
idle.
After command completion occurred, registers were:
ER -- ST COUNT LBA_48 LH LM LL DV DC
-- -- -- == -- == == == -- -- -- -- --
84 -- 51 00 01 00 00 00 00 00 00 f0 00 Error: ICRC, ABRT 1 sectors at LBA =
0x00000000 = 0
Commands leading to the command that caused the error were:
CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name
-- == -- == -- == == == -- -- -- -- -- --------------- --------------------
25 00 00 00 01 00 00 00 00 00 00 f0 00 00:00:56.156 READ DMA EXT
c6 00 00 00 10 00 00 00 00 00 00 f0 00 00:00:56.028 SET MULTIPLE MODE
91 00 00 00 3f 00 0f 00 00 00 00 ff 00 00:00:56.019 INITIALIZE DEVICE
PARAMETERS [OBS-6]
10 00 00 01 00 00 00 00 00 00 00 f0 00 00:00:56.010 RECALIBRATE [OBS-4]
00 00 00 00 01 00 00 00 00 00 00 00 00 00:00:56.001 NOP [Abort queued
commands]
Error 2 [1] occurred at disk power-on lifetime: 1080 hours (45 days + 0 hours)
When the command that caused the error occurred, the device was active or
idle.
After command completion occurred, registers were:
ER -- ST COUNT LBA_48 LH LM LL DV DC
-- -- -- == -- == == == -- -- -- -- --
84 -- 51 00 01 00 00 00 00 00 00 f0 00 Error: ICRC, ABRT 1 sectors at LBA =
0x00000000 = 0
Commands leading to the command that caused the error were:
CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name
-- == -- == -- == == == -- -- -- -- -- --------------- --------------------
25 00 00 00 01 00 00 00 00 00 00 f0 00 00:00:56.156 READ DMA EXT
c6 00 00 00 10 00 00 00 00 00 00 f0 00 00:00:56.028 SET MULTIPLE MODE
91 00 00 00 3f 00 0f 00 00 00 00 ff 00 00:00:56.019 INITIALIZE DEVICE
PARAMETERS [OBS-6]
10 00 00 01 00 00 00 00 00 00 00 f0 00 00:00:56.010 RECALIBRATE [OBS-4]
00 00 00 00 00 00 09 f2 00 50 6e 00 00 00:00:56.001 NOP [Abort queued
commands]
Error 1 [0] occurred at disk power-on lifetime: 995 hours (41 days + 11 hours)
When the command that caused the error occurred, the device was active or
idle.
After command completion occurred, registers were:
ER -- ST COUNT LBA_48 LH LM LL DV DC
-- -- -- == -- == == == -- -- -- -- --
84 -- 51 00 01 00 00 00 00 00 00 e0 00 Error: ICRC, ABRT 1 sectors at LBA =
0x00000000 = 0
Commands leading to the command that caused the error were:
CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name
-- == -- == -- == == == -- -- -- -- -- --------------- --------------------
25 00 03 00 40 00 00 69 00 e4 25 e0 00 01:18:18.317 READ DMA EXT
25 00 03 00 40 00 00 68 00 e4 e5 e0 00 01:18:18.316 READ DMA EXT
25 00 03 00 40 00 00 68 00 e4 a5 e0 00 01:18:18.314 READ DMA EXT
25 00 03 00 40 00 00 68 00 e4 65 e0 00 01:18:18.313 READ DMA EXT
25 00 03 00 40 00 00 68 00 e4 25 e0 00 01:18:18.311 READ DMA EXT
SMART Extended Self-test Log Version: 1 (1 sectors)
Num Test_Description Status Remaining LifeTime(hours)
LBA_of_first_error
# 1 Short offline Completed without error 00% 15080 -
# 2 Extended offline Completed without error 00% 14452 -
# 3 Short offline Completed without error 00% 1092 -
# 4 Extended offline Completed without error 00% 997 -
# 5 Conveyance offline Fatal or unknown error 00% 996 0
# 6 Short offline Completed without error 00% 996 -
1 of 1 failed self-tests are outdated by newer successful extended offline
self-test # 2
SMART Selective self-test log data structure revision number 1
SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
1 0 0 Not_testing
2 0 0 Not_testing
3 0 0 Not_testing
4 0 0 Not_testing
5 0 0 Not_testing
Selective self-test flags (0x0):
After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.
Warning: device does not support SCT Commands
SATA Phy Event Counters (GP Log 0x11) not supported
------------------------------------------------------------------------------
All the data continuously generated in your IT infrastructure contains a
definitive record of customers, application performance, security
threats, fraudulent activity and more. Splunk takes this data and makes
sense of it. Business sense. IT sense. Common sense.
http://p.sf.net/sfu/splunk-d2d-oct
_______________________________________________
Smartmontools-database mailing list
Smartmontools-database@lists.sourceforge.net
https://lists.sourceforge.net/lists/listinfo/smartmontools-database
