hello,
i have some western digital Re drives that are variants of the ones
in the drive database. not sure what the difference is. please add
this guy to the database. smartctl dump is attached
regards
smartctl 6.6 2016-05-31 r4324 [x86_64-linux-4.10.0-28-generic] (local build)
Copyright (C) 2002-16, Bruce Allen, Christian Franke, www.smartmontools.org
=== START OF INFORMATION SECTION ===
Device Model: WDC WD4000FDYZ-27YA5B0
Serial Number: WD-WCC132156748
LU WWN Device Id: 5 0014ee 25f86430e
Firmware Version: 01.01K06
User Capacity: 4,000,787,030,016 bytes [4.00 TB]
Sector Size: 512 bytes logical/physical
Rotation Rate: 7200 rpm
Device is: Not in smartctl database [for details use: -P showall]
ATA Version is: ATA8-ACS (minor revision not indicated)
SATA Version is: SATA 3.0, 6.0 Gb/s (current: 6.0 Gb/s)
Local Time is: Thu Jul 27 16:17:44 2017 PDT
SMART support is: Available - device has SMART capability.
SMART support is: Enabled
AAM feature is: Unavailable
APM level is: 254 (maximum performance)
Rd look-ahead is: Enabled
Write cache is: Enabled
ATA Security is: Disabled, frozen [SEC2]
Wt Cache Reorder: Enabled
=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED
General SMART Values:
Offline data collection status: (0x84) Offline data collection activity
was suspended by an interrupting
command from host.
Auto Offline Data Collection: Enabled.
Self-test execution status: ( 0) The previous self-test routine completed
without error or no self-test has ever
been run.
Total time to complete Offline
data collection: (47400) seconds.
Offline data collection
capabilities: (0x7b) SMART execute Offline immediate.
Auto Offline data collection on/off
support.
Suspend Offline collection upon new
command.
Offline surface scan supported.
Self-test supported.
Conveyance Self-test supported.
Selective Self-test supported.
SMART capabilities: (0x0003) Saves SMART data before entering
power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
General Purpose Logging supported.
Short self-test routine
recommended polling time: ( 2) minutes.
Extended self-test routine
recommended polling time: ( 513) minutes.
Conveyance self-test routine
recommended polling time: ( 5) minutes.
SCT capabilities: (0x70b9) SCT Status supported.
SCT Error Recovery Control supported.
SCT Feature Control supported.
SCT Data Table supported.
SMART Attributes Data Structure revision number: 16
Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAGS VALUE WORST THRESH FAIL RAW_VALUE
1 Raw_Read_Error_Rate POSR-K 200 196 051 - 0
3 Spin_Up_Time POS--K 253 227 021 - 5541
4 Start_Stop_Count -O--CK 100 100 000 - 160
5 Reallocated_Sector_Ct PO--CK 198 198 140 - 85
7 Seek_Error_Rate -OSR-K 200 200 000 - 0
9 Power_On_Hours -O--CK 068 068 000 - 23929
10 Spin_Retry_Count -O--CK 100 100 000 - 0
11 Calibration_Retry_Count -O--CK 100 100 000 - 0
12 Power_Cycle_Count -O--CK 100 100 000 - 148
183 Runtime_Bad_Block -O--CK 100 100 000 - 0
192 Power-Off_Retract_Count -O--CK 200 200 000 - 123
193 Load_Cycle_Count -O--CK 200 200 000 - 49
194 Temperature_Celsius -O---K 108 098 000 - 44
196 Reallocated_Event_Count -O--CK 190 190 000 - 10
197 Current_Pending_Sector -O--CK 200 200 000 - 0
198 Offline_Uncorrectable ----CK 200 200 000 - 0
199 UDMA_CRC_Error_Count -O--CK 200 200 000 - 0
200 Multi_Zone_Error_Rate ---R-- 200 200 000 - 0
||||||_ K auto-keep
|||||__ C event count
||||___ R error rate
|||____ S speed/performance
||_____ O updated online
|______ P prefailure warning
General Purpose Log Directory Version 1
SMART Log Directory Version 1 [multi-sector log support]
Address Access R/W Size Description
0x00 GPL,SL R/O 1 Log Directory
0x01 SL R/O 1 Summary SMART error log
0x02 SL R/O 5 Comprehensive SMART error log
0x03 GPL R/O 6 Ext. Comprehensive SMART error log
0x06 SL R/O 1 SMART self-test log
0x07 GPL R/O 1 Extended self-test log
0x08 GPL R/O 2 Power Conditions log
0x09 SL R/W 1 Selective self-test log
0x10 GPL R/O 1 SATA NCQ Queued Error log
0x11 GPL R/O 1 SATA Phy Event Counters log
0x24 GPL R/O 1 Current Device Internal Status Data log
0x80-0x9f GPL,SL R/W 16 Host vendor specific log
0xa0-0xa7 GPL,SL VS 16 Device vendor specific log
0xa8-0xb1 GPL,SL VS 1 Device vendor specific log
0xb2 GPL VS 65535 Device vendor specific log
0xb2 SL VS 255 Device vendor specific log
0xb3-0xb7 GPL,SL VS 1 Device vendor specific log
0xbd GPL,SL VS 1 Device vendor specific log
0xc0 GPL,SL VS 1 Device vendor specific log
0xc1 GPL VS 24 Device vendor specific log
0xe0 GPL,SL R/W 1 SCT Command/Status
0xe1 GPL,SL R/W 1 SCT Data Transfer
SMART Extended Comprehensive Error Log Version: 1 (6 sectors)
Device Error Count: 151 (device log contains only the most recent 24 errors)
CR = Command Register
FEATR = Features Register
COUNT = Count (was: Sector Count) Register
LBA_48 = Upper bytes of LBA High/Mid/Low Registers ] ATA-8
LH = LBA High (was: Cylinder High) Register ] LBA
LM = LBA Mid (was: Cylinder Low) Register ] Register
LL = LBA Low (was: Sector Number) Register ]
DV = Device (was: Device/Head) Register
DC = Device Control Register
ER = Error register
ST = Status register
Powered_Up_Time is measured from power on, and printed as
DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes,
SS=sec, and sss=millisec. It "wraps" after 49.710 days.
Error 151 [6] occurred at disk power-on lifetime: 23084 hours (961 days + 20
hours)
When the command that caused the error occurred, the device was active or
idle.
After command completion occurred, registers were:
ER -- ST COUNT LBA_48 LH LM LL DV DC
-- -- -- == -- == == == -- -- -- -- --
40 -- 51 00 08 00 01 9e 04 0f 7a e0 00 Error: UNC 8 sectors at LBA =
0x19e040f7a = 6946033530
Commands leading to the command that caused the error were:
CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name
-- == -- == -- == == == -- -- -- -- -- --------------- --------------------
25 00 00 00 08 00 01 9e 04 0f 78 e0 0a 2d+09:42:59.972 READ DMA EXT
25 00 00 00 08 00 01 9e 04 0f 70 e0 0a 2d+09:42:59.972 READ DMA EXT
25 00 00 00 08 00 01 9e 04 0f 68 e0 0a 2d+09:42:59.972 READ DMA EXT
25 00 00 00 08 00 01 9e 04 0f 60 e0 0a 2d+09:42:59.972 READ DMA EXT
25 00 00 00 08 00 01 9e 04 0f 58 e0 0a 2d+09:42:59.972 READ DMA EXT
Error 150 [5] occurred at disk power-on lifetime: 23084 hours (961 days + 20
hours)
When the command that caused the error occurred, the device was active or
idle.
After command completion occurred, registers were:
ER -- ST COUNT LBA_48 LH LM LL DV DC
-- -- -- == -- == == == -- -- -- -- --
40 -- 51 08 00 00 01 9e 04 0f 7a e0 00 Error: UNC 2048 sectors at LBA =
0x19e040f7a = 6946033530
Commands leading to the command that caused the error were:
CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name
-- == -- == -- == == == -- -- -- -- -- --------------- --------------------
25 00 00 08 00 00 01 9e 04 08 00 e0 0a 2d+09:42:56.533 READ DMA EXT
25 00 00 04 00 00 01 9e 04 04 00 e0 0a 2d+09:42:56.478 READ DMA EXT
25 00 00 04 00 00 01 9e 04 00 00 e0 0a 2d+09:42:56.472 READ DMA EXT
25 00 00 02 50 00 01 9e 03 fd b0 e0 0a 2d+09:42:56.469 READ DMA EXT
25 00 00 05 b0 00 01 9e 03 f8 00 e0 0a 2d+09:42:56.462 READ DMA EXT
Error 149 [4] occurred at disk power-on lifetime: 23082 hours (961 days + 18
hours)
When the command that caused the error occurred, the device was active or
idle.
After command completion occurred, registers were:
ER -- ST COUNT LBA_48 LH LM LL DV DC
-- -- -- == -- == == == -- -- -- -- --
40 -- 51 00 08 00 01 41 b5 ac 12 e0 00 Error: UNC 8 sectors at LBA =
0x141b5ac12 = 5397392402
Commands leading to the command that caused the error were:
CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name
-- == -- == -- == == == -- -- -- -- -- --------------- --------------------
25 00 00 00 08 00 01 41 b5 ac 10 e0 0a 2d+07:43:42.001 READ DMA EXT
25 00 00 00 08 00 01 41 b5 ac 08 e0 0a 2d+07:43:42.001 READ DMA EXT
25 00 00 00 08 00 01 41 b5 ac 00 e0 0a 2d+07:43:42.001 READ DMA EXT
25 00 00 00 08 00 01 41 b5 ab f8 e0 0a 2d+07:43:42.000 READ DMA EXT
25 00 00 00 08 00 01 41 b5 ab f0 e0 0a 2d+07:43:42.000 READ DMA EXT
Error 148 [3] occurred at disk power-on lifetime: 23082 hours (961 days + 18
hours)
When the command that caused the error occurred, the device was active or
idle.
After command completion occurred, registers were:
ER -- ST COUNT LBA_48 LH LM LL DV DC
-- -- -- == -- == == == -- -- -- -- --
40 -- 51 00 08 00 01 41 b5 a3 8a e0 00 Error: UNC 8 sectors at LBA =
0x141b5a38a = 5397390218
Commands leading to the command that caused the error were:
CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name
-- == -- == -- == == == -- -- -- -- -- --------------- --------------------
25 00 00 00 08 00 01 41 b5 a3 88 e0 0a 2d+07:43:40.148 READ DMA EXT
25 00 00 00 08 00 01 41 b5 a3 80 e0 0a 2d+07:43:40.148 READ DMA EXT
25 00 00 00 08 00 01 41 b5 a3 78 e0 0a 2d+07:43:40.148 READ DMA EXT
25 00 00 00 08 00 01 41 b5 a3 70 e0 0a 2d+07:43:40.148 READ DMA EXT
25 00 00 00 08 00 01 41 b5 a3 68 e0 0a 2d+07:43:40.148 READ DMA EXT
Error 147 [2] occurred at disk power-on lifetime: 23082 hours (961 days + 18
hours)
When the command that caused the error occurred, the device was active or
idle.
After command completion occurred, registers were:
ER -- ST COUNT LBA_48 LH LM LL DV DC
-- -- -- == -- == == == -- -- -- -- --
40 -- 51 00 08 00 01 41 b5 9b 02 e0 00 Error: UNC 8 sectors at LBA =
0x141b59b02 = 5397388034
Commands leading to the command that caused the error were:
CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name
-- == -- == -- == == == -- -- -- -- -- --------------- --------------------
25 00 00 00 08 00 01 41 b5 9b 00 e0 0a 2d+07:43:38.263 READ DMA EXT
25 00 00 00 08 00 01 41 b5 9a f8 e0 0a 2d+07:43:38.262 READ DMA EXT
25 00 00 00 08 00 01 41 b5 9a f0 e0 0a 2d+07:43:38.262 READ DMA EXT
25 00 00 00 08 00 01 41 b5 9a e8 e0 0a 2d+07:43:38.262 READ DMA EXT
25 00 00 00 08 00 01 41 b5 9a e0 e0 0a 2d+07:43:38.262 READ DMA EXT
Error 146 [1] occurred at disk power-on lifetime: 23082 hours (961 days + 18
hours)
When the command that caused the error occurred, the device was active or
idle.
After command completion occurred, registers were:
ER -- ST COUNT LBA_48 LH LM LL DV DC
-- -- -- == -- == == == -- -- -- -- --
40 -- 51 00 08 00 01 41 b5 92 79 e0 00 Error: UNC 8 sectors at LBA =
0x141b59279 = 5397385849
Commands leading to the command that caused the error were:
CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name
-- == -- == -- == == == -- -- -- -- -- --------------- --------------------
25 00 00 00 08 00 01 41 b5 92 78 e0 0a 2d+07:43:36.413 READ DMA EXT
25 00 00 00 08 00 01 41 b5 92 70 e0 0a 2d+07:43:36.413 READ DMA EXT
25 00 00 00 08 00 01 41 b5 92 68 e0 0a 2d+07:43:36.413 READ DMA EXT
25 00 00 00 08 00 01 41 b5 92 60 e0 0a 2d+07:43:36.413 READ DMA EXT
25 00 00 00 08 00 01 41 b5 92 58 e0 0a 2d+07:43:36.413 READ DMA EXT
Error 145 [0] occurred at disk power-on lifetime: 23082 hours (961 days + 18
hours)
When the command that caused the error occurred, the device was active or
idle.
After command completion occurred, registers were:
ER -- ST COUNT LBA_48 LH LM LL DV DC
-- -- -- == -- == == == -- -- -- -- --
40 -- 51 00 08 00 01 41 b5 89 f1 e0 00 Error: UNC 8 sectors at LBA =
0x141b589f1 = 5397383665
Commands leading to the command that caused the error were:
CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name
-- == -- == -- == == == -- -- -- -- -- --------------- --------------------
25 00 00 00 08 00 01 41 b5 89 f0 e0 0a 2d+07:43:34.558 READ DMA EXT
25 00 00 00 08 00 01 41 b5 89 e8 e0 0a 2d+07:43:34.558 READ DMA EXT
25 00 00 00 08 00 01 41 b5 89 e0 e0 0a 2d+07:43:34.558 READ DMA EXT
25 00 00 00 08 00 01 41 b5 89 d8 e0 0a 2d+07:43:34.558 READ DMA EXT
25 00 00 00 08 00 01 41 b5 89 d0 e0 0a 2d+07:43:34.558 READ DMA EXT
Error 144 [23] occurred at disk power-on lifetime: 23082 hours (961 days + 18
hours)
When the command that caused the error occurred, the device was active or
idle.
After command completion occurred, registers were:
ER -- ST COUNT LBA_48 LH LM LL DV DC
-- -- -- == -- == == == -- -- -- -- --
40 -- 51 00 08 00 01 41 b5 81 69 e0 00 Error: UNC 8 sectors at LBA =
0x141b58169 = 5397381481
Commands leading to the command that caused the error were:
CR FEATR COUNT LBA_48 LH LM LL DV DC Powered_Up_Time Command/Feature_Name
-- == -- == -- == == == -- -- -- -- -- --------------- --------------------
25 00 00 00 08 00 01 41 b5 81 68 e0 0a 2d+07:43:32.677 READ DMA EXT
25 00 00 00 08 00 01 41 b5 81 60 e0 0a 2d+07:43:32.677 READ DMA EXT
25 00 00 00 08 00 01 41 b5 81 58 e0 0a 2d+07:43:32.677 READ DMA EXT
25 00 00 00 08 00 01 41 b5 81 50 e0 0a 2d+07:43:32.677 READ DMA EXT
25 00 00 00 08 00 01 41 b5 81 48 e0 0a 2d+07:43:32.677 READ DMA EXT
SMART Extended Self-test Log Version: 1 (1 sectors)
Num Test_Description Status Remaining LifeTime(hours)
LBA_of_first_error
# 1 Short offline Completed without error 00% 23926 -
# 2 Extended offline Completed without error 00% 23115 -
# 3 Extended offline Aborted by host 90% 23105 -
# 4 Short offline Completed without error 00% 23105 -
# 5 Extended offline Aborted by host 90% 22935 -
# 6 Short offline Completed without error 00% 22911 -
# 7 Short captive Interrupted (host reset) 90% 22911 -
# 8 Extended captive Interrupted (host reset) 90% 22901 -
# 9 Extended offline Aborted by host 90% 22901 -
#10 Short captive Completed without error 00% 22890 -
SMART Selective self-test log data structure revision number 1
SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
1 0 0 Not_testing
2 0 0 Not_testing
3 0 0 Not_testing
4 0 0 Not_testing
5 0 0 Not_testing
Selective self-test flags (0x0):
After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.
SCT Status Version: 3
SCT Version (vendor specific): 258 (0x0102)
SCT Support Level: 1
Device State: Active (0)
Current Temperature: 44 Celsius
Power Cycle Min/Max Temperature: 40/45 Celsius
Lifetime Min/Max Temperature: 19/54 Celsius
Under/Over Temperature Limit Count: 0/0
Vendor specific:
01 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
SCT Temperature History Version: 2
Temperature Sampling Period: 1 minute
Temperature Logging Interval: 1 minute
Min/Max recommended Temperature: 0/60 Celsius
Min/Max Temperature Limit: -41/85 Celsius
Temperature History Size (Index): 478 (78)
Index Estimated Time Temperature Celsius
79 2017-07-27 08:20 44 *************************
... ..( 48 skipped). .. *************************
128 2017-07-27 09:09 44 *************************
129 2017-07-27 09:10 41 **********************
... ..(178 skipped). .. **********************
308 2017-07-27 12:09 41 **********************
309 2017-07-27 12:10 42 ***********************
... ..(150 skipped). .. ***********************
460 2017-07-27 14:41 42 ***********************
461 2017-07-27 14:42 43 ************************
... ..( 67 skipped). .. ************************
51 2017-07-27 15:50 43 ************************
52 2017-07-27 15:51 44 *************************
... ..( 25 skipped). .. *************************
78 2017-07-27 16:17 44 *************************
SCT Error Recovery Control:
Read: 70 (7.0 seconds)
Write: 70 (7.0 seconds)
Device Statistics (GP/SMART Log 0x04) not supported
SATA Phy Event Counters (GP Log 0x11)
ID Size Value Description
0x0001 2 0 Command failed due to ICRC error
0x0002 2 0 R_ERR response for data FIS
0x0003 2 0 R_ERR response for device-to-host data FIS
0x0004 2 0 R_ERR response for host-to-device data FIS
0x0005 2 0 R_ERR response for non-data FIS
0x0006 2 0 R_ERR response for device-to-host non-data FIS
0x0007 2 0 R_ERR response for host-to-device non-data FIS
0x0008 2 0 Device-to-host non-data FIS retries
0x0009 2 9 Transition from drive PhyRdy to drive PhyNRdy
0x000a 2 8 Device-to-host register FISes sent due to a COMRESET
0x000b 2 0 CRC errors within host-to-device FIS
0x000f 2 0 R_ERR response for host-to-device data FIS, CRC
0x0012 2 0 R_ERR response for host-to-device non-data FIS, CRC
0x8000 4 1653355 Vendor specific
------------------------------------------------------------------------------
Check out the vibrant tech community on one of the world's most
engaging tech sites, Slashdot.org! http://sdm.link/slashdot
_______________________________________________
Smartmontools-database mailing list
Smartmontools-database@lists.sourceforge.net
https://lists.sourceforge.net/lists/listinfo/smartmontools-database