Joao Pedras wrote: > Mike Tancsa wrote: >> At 07:51 PM 10/3/2007, Soren Kristensen wrote: >>> Hi Everybody, >>> >>> I just posted a net5501 BIOS update with: >>> comBIOS vers 1.32h >>> >>> * fixed IDE DMA enable issue on net5501 >>> * fixed soft reboot issue on net5501 >> >> Hi, >> Unfortunately, I still see the soft reboot issue on FreeBSD. >> e.g. from the bootloader prompt, if I try to reboot, the box will >> hang and never reboot >> >> Nothing fancy about my bios settings, other than the speed is set to 9600 >> >> >> >> POST: 012345689bcefghips1234ajklnopqr,,,tvwxy >> >> >> >> >> >> >> >> >> comBIOS ver. 1.32h 20071004 Copyright (C) 2000-2007 Soekris Engineering. >> >> net5501 >> >> 0512 Mbyte Memory CPU Geode LX 500 Mhz >> >> Pri Sla LEXAR ATA FLASH LBA 994-16-63 501 Mbyte >> >> Slot Vend Dev ClassRev Cmd Stat CL LT HT Base1 Base2 Int >> ------------------------------------------------------------------- >> 0:01:2 1022 2082 10100000 0006 0220 08 00 00 A0000000 00000000 10 >> 0:06:0 1106 3053 02000096 0117 0210 08 40 00 0000E101 A0004000 11 >> 0:07:0 1106 3053 02000096 0117 0210 08 40 00 0000E201 A0004100 05 >> 0:08:0 1106 3053 02000096 0117 0210 08 40 00 0000E301 A0004200 09 >> 0:09:0 1106 3053 02000096 0117 0210 08 40 00 0000E401 A0004300 12 >> 0:20:0 1022 2090 06010003 0009 02A0 08 40 80 00006001 00006101 >> 0:20:2 1022 209A 01018001 0005 02A0 08 00 00 00000000 00000000 >> 0:21:0 1022 2094 0C031002 0006 0230 08 00 80 A0005000 00000000 15 >> 0:21:1 1022 2095 0C032002 0006 0230 08 00 00 A0006000 00000000 15 >> >> 1 Seconds to automatic boot. Press Ctrl-P for entering Monitor. >> >> 1 FreeBSD >> 2 FreeBSD >> >> Default: 1 >> >> /boot.config: -hConsoles: serial port >> BIOS drive C: is disk0 >> BIOS 639kB/523264kB available memory >> >> FreeBSD/i386 bootstrap loader, Revision 1.1 >> ([EMAIL PROTECTED], Sat Sep 15 01:52:01 EDT 2007) >> Loading /boot/defaults/loader.conf >> /boot/kernel/kernel text=0x258e14 data=0x2bed4+0x16018 >> syms=[0x4+0x359d0+0x4+0x45239] >> - >> Hit [Enter] to boot immediately, or any other key for command prompt. >> >> >> Type '?' for a list of commands, 'help' for more detailed help. >> OK reboot >> Rebooting... >> >> at this point its totally hung and needs a power cycle >> >> >> >> >> dmesg looks like the following >> >> >> Copyright (c) 1992-2007 The FreeBSD Project. >> Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994 >> The Regents of the University of California. All rights reserved. >> FreeBSD is a registered trademark of The FreeBSD Foundation. >> FreeBSD 6.2-STABLE #1: Tue Sep 18 11:35:06 EDT 2007 >> [EMAIL PROTECTED]:/usr/obj/nanobsd-soekris5501/usr/src/sys/nano5501 >> Timecounter "i8254" frequency 1193182 Hz quality 0 >> CPU: Geode(TM) Integrated Processor by AMD PCS (499.90-MHz 586-class CPU) >> Origin = "AuthenticAMD" Id = 0x5a2 Stepping = 2 >> Features=0x88a93d<FPU,DE,PSE,TSC,MSR,CX8,SEP,PGE,CMOV,CLFLUSH,MMX> >> AMD Features=0xc0400000<MMX+,3DNow+,3DNow> >> real memory = 536870912 (512 MB) >> avail memory = 520265728 (496 MB) >> K6-family MTRR support enabled (2 registers) >> cpu0 on motherboard >> pcib0: <Host to PCI bridge> pcibus 0 on motherboard >> pci0: <PCI bus> on pcib0 >> Geode LX: Soekris net5501 comBIOS ver. 1.32h 20071004 Copyright (C) 2000-2007 >> MFGPT bar: f00100006200 >> pci0: <encrypt/decrypt, entertainment crypto> at device 1.2 (no >> driver attached) >> vr0: <VIA VT6105M Rhine III 10/100BaseTX> port 0xe100-0xe1ff mem >> 0xa0004000-0xa00040ff irq 11 at device 6.0 on pci0 >> miibus0: <MII bus> on vr0 >> ukphy0: <Generic IEEE 802.3u media interface> on miibus0 >> ukphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto >> vr0: Ethernet address: 00:00:24:c8:e2:24 >> vr1: <VIA VT6105M Rhine III 10/100BaseTX> port 0xe200-0xe2ff mem >> 0xa0004100-0xa00041ff irq 5 at device 7.0 on pci0 >> miibus1: <MII bus> on vr1 >> ukphy1: <Generic IEEE 802.3u media interface> on miibus1 >> ukphy1: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto >> vr1: Ethernet address: 00:00:24:c8:e2:25 >> vr2: <VIA VT6105M Rhine III 10/100BaseTX> port 0xe300-0xe3ff mem >> 0xa0004200-0xa00042ff irq 9 at device 8.0 on pci0 >> miibus2: <MII bus> on vr2 >> ukphy2: <Generic IEEE 802.3u media interface> on miibus2 >> ukphy2: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto >> vr2: Ethernet address: 00:00:24:c8:e2:26 >> vr3: <VIA VT6105M Rhine III 10/100BaseTX> port 0xe400-0xe4ff mem >> 0xa0004300-0xa00043ff irq 12 at device 9.0 on pci0 >> miibus3: <MII bus> on vr3 >> ukphy3: <Generic IEEE 802.3u media interface> on miibus3 >> ukphy3: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto >> vr3: Ethernet address: 00:00:24:c8:e2:27 >> isab0: <PCI-ISA bridge> at device 20.0 on pci0 >> isa0: <ISA bus> on isab0 >> atapci0: <GENERIC ATA controller> port >> 0x1f0-0x1f7,0x3f6,0x170-0x177,0x376,0xe000-0xe00f at device 20.2 on pci0 >> ata0: <ATA channel 0> on atapci0 >> ata1: <ATA channel 1> on atapci0 >> ohci0: <OHCI (generic) USB controller> mem 0xa0005000-0xa0005fff irq >> 15 at device 21.0 on pci0 >> ohci0: [GIANT-LOCKED] >> usb0: OHCI version 1.0, legacy support >> usb0: <OHCI (generic) USB controller> on ohci0 >> usb0: USB revision 1.0 >> uhub0: AMD OHCI root hub, class 9/0, rev 1.00/1.00, addr 1 >> uhub0: 4 ports with 4 removable, self powered >> pci0: <serial bus, USB> at device 21.1 (no driver attached) >> orm0: <ISA Option ROM> at iomem 0xc8000-0xd27ff on isa0 >> sio0 at port 0x3f8-0x3ff irq 4 flags 0x10 on isa0 >> sio0: type 16550A, console >> sio1 at port 0x2f8-0x2ff irq 3 on isa0 >> sio1: type 16550A >> Timecounter "TSC" frequency 499904611 Hz quality 800 >> Timecounters tick every 1.000 msec >> ad1: 489MB <LEXAR ATA FLASH V1.02> at ata0-slave PIO4 >> Trying to mount root from ufs:/dev/ad1s1a >> >> >> ---Mike >> >> >>> * change initial clear screen to scroll lines >>> >>> There might still be issues with Ultra-DMA detect/setting, I would be >>> happy to get a few success/failure reports, just email me directly. >>> >>> Also, I'm still investigating how 40/80 wire cable reporting should be >>> done.... >>> >>> >>> Best Regards, >>> >>> >>> Soren Kristensen >>> >>> CEO & Chief Engineer >>> Soekris Engineering, Inc. >>> >>> _______________________________________________ >>> Soekris-tech mailing list >>> [email protected] >>> http://lists.soekris.com/mailman/listinfo/soekris-tech >> _______________________________________________ >> Soekris-tech mailing list >> [email protected] >> http://lists.soekris.com/mailman/listinfo/soekris-tech > > Same problem here, with the soft boot. > > Additionaly, when inserting a SANDISK 512Mb, it doesn't boot. I am not > sure if this is related with your recent issues since this was the first > time I tried this particular flash on the 5501. It was working well on a > 4801 and it has always been used read-only. > > It locks up/stops right before this part shows up (ie. this never showsup): > > Slot Vend Dev ClassRev Cmd Stat CL LT HT Base1 Base2 Int > ------------------------------------------------------------------- > 0:01:2 1022 2082 10100000 0006 0220 08 00 00 A0000000 00000000 10 > 0:06:0 1106 3053 02000096 0117 0210 08 40 00 0000E101 A0004000 11 > 0:07:0 1106 3053 02000096 0117 0210 08 40 00 0000E201 A0004100 05 > 0:08:0 1106 3053 02000096 0117 0210 08 40 00 0000E301 A0004200 09 > 0:09:0 1106 3053 02000096 0117 0210 08 40 00 0000E401 A0004300 12 > > > Thanks. > _______________________________________________ > Soekris-tech mailing list > [email protected] > http://lists.soekris.com/mailman/listinfo/soekris-tech
I am not sure if this is related as well. The only box I have with the new bios, booting FreeBSD 6.2-STABLE from yesterday, is not able to bring the vr interfaces up. During kernel probing the message "MII without any phy!" shows up with all of them. First I thought I had messed up my kernel config but I really didn't changed anything. I just had the chance to boot the *exact* same flash on a 5501 with the previous BIOS version and the problem does not occur. Again, not sure if this is related with your new BIOS version. Thanks! _______________________________________________ Soekris-tech mailing list [email protected] http://lists.soekris.com/mailman/listinfo/soekris-tech
