The answer was quite simple (and probably obvious to some). I had to turn of flow control on the serial port, which it actually says in the settings for the minicom on the wiki.
Thanks, Pontus. Pontus wrote: > Stuart Henderson wrote: > >> On 2008-02-24, Pontus <[EMAIL PROTECTED]> wrote: >> >> >>> Have you updated the comBIOS and how did you go about it? >>> >>> >> this is described on http://wiki.soekris.info/ >> >> >> >> > Ok, so first I try what is described on the wiki: > > 1. download - > 2. ~+sx b5501_132i.bin > > (the ~C is not available in my version of cu, also instead of lsz (which > I don't have) i use sx, which should be the same) > > I get the following output (which is the same if i try to use minicom): > > >> download - >> > > Start sending file using XMODEM/CRC protocol. > ~+ sx b5501_132i.bin > Sending b5501_132i.bin, 784 blocks: Give your local XMODEM receive > command now. > Xmodem sectors/kbytes sent: 0/ 0kRetry 0: NAK on sector > Retry 0: NAK on sector > Retry 0: NAK on sector > Retry 0: NAK on sector > Retry 0: NAK on sector > Retry 0: NAK on sector > Retry 0: NAK on sector > Retry 0: NAK on sector > Retry 0: NAK on sector > Retry 0: NAK on sector > Retry 0: NAK on sector > Retry 0: Retry Count Exceeded > > Transfer incomplete > cu: shell: Exit status 128 > > Invalid Command. > > > > If I try again but skip the "-" on download, I get: > > >> download >> > > Start sending file using XMODEM/CRC protocol. > CCCCCC~C+CCCCCCCCsx b5501_132i.binC > Sending b5501_132i.bin, 784 blocks: Give your local XMODEM receive > command now. > Xmodem sectors/kbytes sent: 0/ 0kRetry 0: NAK on sector > Retry 0: NAK on sector > Retry 0: NAK on sector > Retry 0: NAK on sector > Retry 0: NAK on sector > Retry 0: NAK on sector > Retry 0: NAK on sector > Retry 0: NAK on sector > Retry 0: NAK on sector > Retry 0: NAK on sector > Retry 0: NAK on sector > Retry 0: Retry Count Exceeded > > Transfer incomplete > cu: shell: Exit status 128 > > Invalid Command. > > > > Lastly, If i try to use the cu command ~> which should send a file over > the serial line, I get: > > >> download - >> > > Start sending file using XMODEM/CRC protocol. > ~> > File to send: b5501_132i.bin > 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 > 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 > 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 > 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 > 100 101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 > 118 119 120 121 122 123 124 125 126 127 128 129 130 131 132 133 134 135 > 136 137 138 139 140 141 142 143 144 145 146 147 148 149 150 151 152 153 > 154 155 156 157 158 159 160 161 162 163 164 165 166 167 168 169 170 171 > 172 173 174 175 176 177 178 179 180 181 182 183 184 185 186 187 188 189 > 190 191 192 193 194 195 196 197 198 199 200 201 202 203 204 205 206 207 > 208 209 210 211 212 213 214 215 216 217 218 219 220 221 222 223 224 225 > 226 227 228 229 230 231 232 233 234 235 236 237 238 239 240 241 242 243 > 244 245 246 247 248 249 250 251 252 253 254 255 256 257 258 259 260 261 > 262 263 264 265 266 267 268 269 270 271 272 273 274 275 276 277 278 279 > 280 281 282 283 284 285 286 287 288 289 290 291 292 293 294 295 296 297 > 298 299 300 301 302 303 304 305 306 307 308 309 310 311 312 313 314 315 > 316 317 318 319 320 321 322 323 324 325 326 327 328 329 330 331 332 333 > 334 335 336 337 338 339 340 341 342 343 344 345 346 347 348 349 350 351 > 352 353 354 355 356 357 358 359 360 361 362 363 364 365 366 367 368 369 > 370 371 372 373 374 375 376 377 378 379 380 381 382 383 384 385 386 387 > 388 389 390 391 392 393 394 395 396 397 398 399 400 401 402 403 404 405 > 406 407 408 409 410 411 412 413 414 415 416 417 418 419 420 421 422 423 > 424 425 426 427 428 429 430 431 432 433 434 435 436 437 438 439 440 441 > 442 443 > [file transfer complete] > [connected] > id Command. > > >> ff&}pu6EtftNf+$fffff fau&<<3ftfff0f 0F >> > Invalid Command. > > >> t *0ua`< su Fu:~Ia >> > Invalid Command. > > >> Cmd Stat L LT HT Base1 Base2 Int >> > Invalid Command. > > >> ---------------------------------------Bus .J<ZtSJ9MV;M >> > DM6FMMMBOM &t)1w%_ > Invalid Command. > > >> + >> > Invalid Command. > > >> .M >> > Invalid Command. > > >> fRfW&tf_fZY[ft >> > Invalid Command. > > >> Qff.\^*ft3 t+Ut#tt.lu.4u.4f.4f.4.>\.f.Df.L2 >> > Invalid Command. > > > > > Now I don't know what to do next? Have I overlooked something obvious? > > Sorry for the long post. > > Regards, > Pontus. > > > _______________________________________________ > Soekris-tech mailing list > [email protected] > http://lists.soekris.com/mailman/listinfo/soekris-tech > _______________________________________________ Soekris-tech mailing list [email protected] http://lists.soekris.com/mailman/listinfo/soekris-tech
