Hello
I have a problem with my net5501 soekris. I have tried installing debian
on it and it went fine, until I tried to boot up it was not able to
mount the root on the sata disk.
Then I tried to install to the flash card, in went good, but I am still
not able to mount the sata disk. Its a brand new hitachi 250 gb sata disk.
Below is output from the bootup
What can be wrong ???
1.
.
2.
3.
4.
POST: 012345689bcefghips1234ajklnopqr,,,tvwxy
5.
6.
7.
8.
9.
10.
11.
12.
13.
comBIOS ver. 1.33 20070103 Copyright (C) 2000-2007 Soekris
Engineering.
14.
15.
net5501
16.
17.
CPU Geode LX 500 Mhz 0000 Mbyte Memory0512
18.
19.
Pri Mas Hitachi HTS542525K9SA00 LBA Xlt 1024-255-63 134 Gbyte
20.
Pri Sla SanDisk SDCFH2-4096 LBA Xlt 995-128-63 4013 Mbyte
21.
22.
Slot Vend Dev ClassRev Cmd Stat CL LT HT Base1 Base2 Int
23.
-------------------------------------------------------------------
24.
0:01:2 1022 2082 10100000 0006 0220 08 00 00 A0000000 00000000 10
25.
0:06:0 1106 3053 02000096 0117 0210 08 40 00 0000E101 A0004000 11
26.
0:07:0 1106 3053 02000096 0117 0210 08 40 00 0000E201 A0004100 05
27.
0:08:0 1106 3053 02000096 0117 0210 08 40 00 0000E301 A0004200 09
28.
0:09:0 1106 3053 02000096 0117 0210 08 40 00 0000E401 A0004300 12
29.
0:20:0 1022 2090 06010003 0009 02A0 08 40 80 00006001 00006101
30.
0:20:2 1022 209A 01018001 0005 02A0 08 00 00 00000000 00000000
31.
0:21:0 1022 2094 0C031002 0006 0230 08 00 80 A0005000 00000000 15
32.
0:21:1 1022 2095 0C032002 0006 0230 08 00 00 A0006000 00000000 15
33.
34.
Seconds to automatic boot. Press Ctrl-P for entering Monitor. 5 4
3 2 1
35.
GRUB Loading stage1.5.
36.
37.
38.
GRUB loading, please wait...
39.
40.
GNU GRUB version 0.97 (639K lower / 523264K upper memory)
41.
42.
+-------------------------------------------------------------------------+||||||||||||||||||||||||+-------------------------------------------------------------------------+
43.
Use the ^ and v keys to select which entry is highlighted.
44.
Press enter to boot the selected OS, 'e' to edit the
45.
commands before booting, or 'c' for a command-line. Debian
GNU/Linux, kernel 2.6.18-6-486 Debian GNU/Linux, kernel
2.6.18-6-486 (single-user mode) The highlighted entry will be
booted automatically in 5 seconds. The highlighted entry will be
booted automatically in 4 seconds. The highlighted entry will be
booted automatically in 3 seconds. The highlighted entry will be
booted automatically in 2 seconds. The highlighted entry will be
booted automatically in 1 seconds. Booting 'Debian GNU/Linux,
kernel 2.6.18-6-486'
46.
47.
root (hd1,0)
48.
Filesystem type is ext2fs, partition type 0x83
49.
kernel /boot/vmlinuz-2.6.18-6-486 root=/dev/hdb1 ro
console=ttyS0,9600n8
50.
[Linux-bzImage, setup=0x1e00, size=0x127a1b]
51.
initrd /boot/initrd.img-2.6.18-6-486
52.
[Linux-initrd @ 0x1fbce000, 0x4211b4 bytes]
53.
savedefault
54.
55.
Linux version 2.6.18-6-486 (Debian 2.6.18.dfsg.1-18etch1)
([EMAIL PROTECTED]) (gcc version 4.1.2 20061115 (prerelease)
(Debian 4.1.1-21)) #1 Sun Feb 10 22:06:33 UTC 2008
56.
BIOS-provided physical RAM map:
57.
BIOS-e820: 0000000000000000 - 000000000009fc00 (usable)
58.
BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved)
59.
BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved)
60.
BIOS-e820: 0000000000100000 - 0000000020000000 (usable)
61.
BIOS-e820: 00000000fff00000 - 0000000100000000 (reserved)
62.
512MB LOWMEM available.
63.
DMI not present or invalid.
64.
ACPI: Unable to locate RSDP
65.
Allocating PCI resources starting at 30000000 (gap: 20000000:dff00000)
66.
Detected 499.934 MHz processor.
67.
Built 1 zonelists. Total pages: 131072
68.
Kernel command line: root=/dev/hdb1 ro console=ttyS0,9600n8
69.
No local APIC present or hardware disabled
70.
Initializing CPU#0
71.
PID hash table entries: 4096 (order: 12, 16384 bytes)
72.
Console: colour dummy device 80x25
73.
Dentry cache hash table entries: 65536 (order: 6, 262144 bytes)
74.
Inode-cache hash table entries: 32768 (order: 5, 131072 bytes)
75.
Memory: 512336k/524288k available (1499k kernel code, 11356k
reserved, 599k data, 256k init, 0k highmem)
76.
Checking if this processor honours the WP bit even in supervisor
mode... Ok.
77.
Calibrating delay using timer specific routine.. 1001.08 BogoMIPS
(lpj=2002179)
78.
Security Framework v1.0.0 initialized
79.
SELinux: Disabled at boot.
80.
Capability LSM initialized
81.
Mount-cache hash table entries: 512
82.
CPU: L1 I Cache: 64K (32 bytes/line), D cache 64K (32 bytes/line)
83.
CPU: L2 Cache: 128K (32 bytes/line)
84.
Compat vDSO mapped to ffffe000.
85.
CPU: AMD Geode(TM) Integrated Processor by AMD PCS stepping 02
86.
Checking 'hlt' instruction... OK.
87.
checking if image is initramfs... it is
88.
Freeing initrd memory: 4228k freed
89.
NET: Registered protocol family 16
90.
EISA bus registered
91.
PCI: PCI BIOS revision 2.01 entry at 0xfac61, last bus=0
92.
PCI: Using configuration type 1
93.
Setting up standard PCI resources
94.
ACPI: Interpreter disabled.
95.
Linux Plug and Play Support v0.97 (c) Adam Belay
96.
pnp: PnP ACPI: disabled
97.
PnPBIOS: Scanning system for PnP BIOS support...
98.
PnPBIOS: PnP BIOS support was not detected.
99.
PCI: Probing PCI hardware
100.
NET: Registered protocol family 2
101.
IP route cache hash table entries: 16384 (order: 4, 65536 bytes)
102.
TCP established hash table entries: 65536 (order: 6, 262144 bytes)
103.
TCP bind hash table entries: 32768 (order: 5, 131072 bytes)
104.
TCP: Hash tables configured (established 65536 bind 32768)
105.
TCP reno registered
106.
audit: initializing netlink socket (disabled)
107.
audit(342510776.888:1): initialized
108.
VFS: Disk quotas dquot_6.5.1
109.
Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
110.
Initializing Cryptographic API
111.
io scheduler noop registered
112.
io scheduler anticipatory registered
113.
io scheduler deadline registered
114.
io scheduler cfq registered (default)
115.
isapnp: Scanning for PnP cards...
116.
isapnp: No Plug & Play device found
117.
Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing
enabled
118.
serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
119.
serial8250: ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
120.
RAMDISK driver initialized: 16 RAM disks of 8192K size 1024 blocksize
121.
PNP: No PS/2 controller found. Probing ports directly.
122.
serio: i8042 AUX port at 0x60,0x64 irq 12
123.
serio: i8042 KBD port at 0x60,0x64 irq 1
124.
mice: PS/2 mouse device common for all mice
125.
EISA: Probing bus 0 at eisa.0
126.
EISA: Detected 0 cards.
127.
TCP bic registered
128.
NET: Registered protocol family 1
129.
NET: Registered protocol family 17
130.
NET: Registered protocol family 8
131.
NET: Registered protocol family 20
132.
Using IPI Shortcut mode
133.
Freeing unused kernel memory: 256k freed
134.
Time: tsc clocksource has been installed.
135.
Loading, please wait...
136.
Begin: Loading essential drivers... ...
137.
Done.
138.
Begin: Running /scripts/init-premount ...
139.
FATAL: Error inserting fan
(/lib/modules/2.6.18-6-486/kernel/drivers/acpi/fan.ko): No such device
140.
FATAL: Error inserting thermal
(/lib/modules/2.6.18-6-486/kernel/drivers/acpi/thermal.ko): No
such device
141.
via-rhine.c:v1.10-LK1.4.1 July-24-2006 Written by Donald Becker
142.
eth0: VIA Rhine III (Management Adapter) at 0x1e100,
00:00:24:c8:e2:a4, IRQ 11.
143.
eth0: MII PHY found at address 1, status 0x786d advertising 05e1
Link 45e1.
144.
eth1: VIA Rhine III (Management Adapter) at 0x1e200,
00:00:24:c8:e2:a5, IRQ 5.
145.
eth1: MII PHY found at address 1, status 0x7849 advertising 05e1
Link 0000.
146.
eth2: VIA Rhine III (Management Adapter) at 0x1e300,
00:00:24:c8:e2:a6, IRQ 9.
147.
eth2: MII PHY found at address 1, status 0x7849 advertising 05e1
Link 0000.
148.
eth3: VIA Rhine III (Management Adapter) at 0x1e400,
00:00:24:c8:e2:a7, IRQ 12.
149.
eth3: MII PHY found at address 1, status 0x7849 advertising 05e1
Link 0000.
150.
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
151.
ide: Assuming 33MHz system bus speed for PIO modes; override with
idebus=xx
152.
AMD5536: IDE controller at PCI slot 0000:00:14.2
153.
AMD5536: chipset revision 1
154.
AMD5536: not 100% native mode: will probe irqs later
155.
AMD5536: 0000:00:14.2 (rev 01) UDMA100 controller
156.
ide0: BM-DMA at 0xe000-0xe007, BIOS settings: hda:pio, hdb:pio
157.
usbcore: registered new driver usbfs
158.
usbcore: registered new driver hub
159.
hda: Hitachi HTS542525K9SA00, ATA DISK drive
160.
hdb: SanDisk SDCFH2-4096, CFA DISK drive
161.
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
162.
ehci_hcd 0000:00:15.1: EHCI Host Controller
163.
ehci_hcd 0000:00:15.1: new USB bus registered, assigned bus number 1
164.
ehci_hcd 0000:00:15.1: irq 15, io mem 0xa0006000
165.
ehci_hcd 0000:00:15.1: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
166.
usb usb1: configuration #1 chosen from 1 choice
167.
hub 1-0:1.0: USB hub found
168.
hub 1-0:1.0: 4 ports detected
169.
hda: max request size: 512KiB
170.
ohci_hcd 0000:00:15.0: OHCI Host Controller
171.
ohci_hcd 0000:00:15.0: new USB bus registered, assigned bus number 2
172.
ohci_hcd 0000:00:15.0: irq 15, io mem 0xa0005000
173.
usb usb2: configuration #1 chosen from 1 choice
174.
hub 2-0:1.0: USB hub found
175.
hub 2-0:1.0: 4 ports detected
176.
hda: 488397168 sectors (250059 MB) w/7229KiB Cache,
CHS=30401/255/63, UDMA(33)
177.
hda: cache flushes supported
178.
hda:hda: dma_intr: status=0x51 { DriveReady SeekComplete Error }
179.
hda: dma_intr: error=0x84 { DriveStatusError BadCRC }
180.
ide: failed opcode was: unknown
181.
hda: dma_intr: status=0x51 { DriveReady SeekComplete Error }
182.
hda: dma_intr: error=0x84 { DriveStatusError BadCRC }
183.
ide: failed opcode was: unknown
184.
hda: dma_intr: status=0x51 { DriveReady SeekComplete Error }
185.
hda: dma_intr: error=0x84 { DriveStatusError BadCRC }
186.
ide: failed opcode was: unknown
187.
hda: dma_intr: status=0x51 { DriveReady SeekComplete Error }
188.
hda: dma_intr: error=0x84 { DriveStatusError BadCRC }
189.
ide: failed opcode was: unknown
190.
hdb: DMA disabled
191.
ide0: reset: success
192.
hda: dma_intr: status=0x51 { DriveReady SeekComplete Error }
193.
hda: dma_intr: error=0x84 { DriveStatusError BadCRC }
194.
ide: failed opcode was: unknown
195.
hda: dma_intr: status=0x51 { DriveReady SeekComplete Error }
196.
hda: dma_intr: error=0x84 { DriveStatusError BadCRC }
197.
ide: failed opcode was: unknown
198.
hda: dma_intr: status=0x51 { DriveReady SeekComplete Error }
199.
hda: dma_intr: error=0x84 { DriveStatusError BadCRC }
200.
ide: failed opcode was: unknown
201.
hda: dma_intr: status=0x51 { DriveReady SeekComplete Error }
202.
hda: dma_intr: error=0x84 { DriveStatusError BadCRC }
203.
ide: failed opcode was: unknown
204.
ide0: reset: success
205.
hda: dma_intr: status=0x51 { DriveReady SeekComplete Error }
206.
hda: dma_intr: error=0x84 { DriveStatusError BadCRC }
207.
ide: failed opcode was: unknown
208.
end_request: I/O error, dev hda, sector 0
209.
Buffer I/O error on device hda, logical block 0
210.
hda: dma_intr: status=0x51 { DriveReady SeekComplete Error }
211.
hda: dma_intr: error=0x84 { DriveStatusError BadCRC }
212.
ide: failed opcode was: unknown
213.
hda: dma_intr: status=0x51 { DriveReady SeekComplete Error }
214.
hda: dma_intr: error=0x84 { DriveStatusError BadCRC }
215.
ide: failed opcode was: unknown
216.
hda: dma_intr: status=0x51 { DriveReady SeekComplete Error }
217.
hda: dma_intr: error=0x84 { DriveStatusError BadCRC }
218.
ide: failed opcode was: unknown
219.
hda: dma_intr: status=0x51 { DriveReady SeekComplete Error }
220.
hda: dma_intr: error=0x84 { DriveStatusError BadCRC }
221.
ide: failed opcode was: unknown
222.
ide0: reset: success
223.
unable to read partition table
224.
hdb: max request size: 128KiB
225.
hdb: 8027712 sectors (4110 MB) w/1KiB Cache, CHS=7964/16/63
226.
hdb: hdb1 hdb2 < hdb5 >
227.
Done.
228.
Begin: Mounting root file system... ...
229.
Begin: Running /scripts/local-top ...
230.
Done.
231.
Begin: Running /scripts/local-premount ...
232.
kinit: name_to_dAttempting manual resume
233.
ev_t(/dev/hdb5) = hdb5(3,69)
234.
kinit: trying to resume from /dev/hdb5
235.
kinit: No kjournald starting. Commit interval 5 seconds
236.
resume image, doEXT3-fs: mounted filesystem with ordered data mode.
237.
ing normal boot...
238.
Done.
239.
Begin: Running /scripts/local-bottom ...
240.
Done.
241.
Done.
242.
Begin: Running /scripts/init-bottom ...
243.
Done.
244.
INIT: version 2.86 booting
245.
Starting the hotplug events dispatcher: udevd.
246.
Synthesizing the initial hotplug events...done.
247.
Waiting for /dev to be fully populated...AMD Geode RNG detected
248.
input: PC Speaker as /class/input/input0
249.
done.
250.
Activating swap...Adding 224868k swap on /dev/hdb5. Priority:-1
extents:1 across:224868k
251.
done.
252.
Checking root file system...fsck 1.40-WIP (14-Nov-2006)
253.
/dev/hdb1: cleanEXT3 FS on hdb1, , 25432/473280 finternal journal
254.
iles, 147005/945819 blocks
255.
done.
256.
Setting the system clock..
257.
Cleaning up ifupdown....
258.
Loading kernel modules...loop: loaded (max 8 devices)
259.
done.
260.
Loading device-mapper supportdevice-mapper: ioctl: 4.7.0-ioctl
(2006-06-24) initialised: [EMAIL PROTECTED]
261.
.
262.
Checking file systems...fsck 1.40-WIP (14-Nov-2006)
263.
done.
264.
Setting kernel variables...done.
265.
Mounting local filesystems...mount: /dev/usbdev1.1_ep00 is not a
block device
266.
failed.
267.
Activating swapfile swap...done.
268.
Setting up networking....
269.
Configuring network interfaces...done.
270.
Starting portmap daemon....
271.
eth0: link up, 100Mbps, full-duplex, lpa 0x45E1
272.
Setting console screen modes and fonts.
273.
INIT: Entering runlevel: 2
274.
Starting system log daemon: syslogd.
275.
Starting kernel log daemon: klogd.
276.
Starting portmap daemon...Already running..
277.
Starting MTA: exim4.
278.
Starting internet superserver: inetd.
279.
Starting NFS common utilities: statd.
280.
Starting deferred execution scheduler: atd.
281.
Starting periodic command scheduler: crond.
282.
283.
Debian GNU/Linux 4.0 seapig ttyS0
284.
285.
seapig login:
_______________________________________________
Soekris-tech mailing list
[email protected]
http://lists.soekris.com/mailman/listinfo/soekris-tech
