How do you run Softimage/Batch? You should always use tcsh or csh... You could also try to replace the whole mainwin folder with the one from the working 2012 installation and see if it runs then.
> Jean-Louis Billard <[email protected]> hat am 12. Mai 2015 um 14:16 > geschrieben: > > Hi Thomas, > > Basically: > > > > > ======================================================= > > Autodesk Softimage 13.1.140.0 > > ======================================================= > > > > Aborted (core dumped) > > > > > > I also tried installing 2011SP1, 2012 and 2014SP1. > The problem only appears with 2014SP1 and 2015SP1, previous versions are ok > (I don’t have a 2013 installer so I didn’t check) > > The /etc/hosts file issue, I remember that now that you mention it. > Wasn’t it something to do with it needing to be formatted for csh rather than > bash, or something of the sort? > I’ll dig down there a bit… > > Thanks, > > Jean-Louis > Digital Golem > > > > > > On 11 May 2015, at 18:48, Thomas Volkmann > > > <[email protected] <mailto:[email protected]> > wrote: > > > > What error are you getting on startup/xsibatch? There has been an issue > > with a wrongly formatted /etc/hosts file that caused segmentation > > faults...just a shot in the dark > > > > > > > > > Jean-Louis Billard <[email protected] > > > > > <mailto:[email protected]> > hat am 11. Mai 2015 um 16:10 > > > > > geschrieben: > > > > > > I would love to ignore it, but alas I still get a core dump when > > > running xsibatch! > > > > > > Looking around I’m finding some people talking about updating OGL > > > drivers, some discussing the Xorg.conf file, and yet more mentioning > > > kernel tweaks. It’s tricky to guess the best route… > > > > > > Jean-Louis > > > > > > Digital Golem > > > > > > > > > > > > > > > > > > > On 11 May 2015, at 15:56, Stephen Blair > > > > > > > <[email protected] > > > > > > > <mailto:[email protected]> > wrote: > > > > > > > > I had the same error but I ignored it, just to see if > > > > Softimage would start (and it did). > > > > > > > > SAS is a set of DisplayCallbacks for OpenGL and DirectX > > > > > > > > > > > > On Mon, May 11, 2015 at 9:19 AM, Jean-Louis Billard > > > > <[email protected] <mailto:[email protected]> > wrote: > > > > > > > > > Hi Stephen, > > > > > > > > > > So I tried, but for some reason only the first line runs > > > > > ok. The second one spurts this: > > > > > > > > > > > ./Application/bin/cmdreg -f > > > > > > "Application/Plugins/PLUGINSCOMDLLs.lst” > > > > > > > > > > Loading ../Plugins/libSAS.so: Unable to load library > > > > > (Error code 126: The specified module could not be found). Running > > > > > REGSVR32.EXE may provide more information > > > > > > > > > > libSAS.so is present in /Plugins, so I’m not sure what’s > > > > > going on…? > > > > > > > > > > > > > > > Maybe I should roll back to Centos 6.2, which seems to be > > > > > the officially supported version for Soft2015_SP1? > > > > > > > > > > Thanks for any help. > > > > > > > > > > > > > > > Jean-Louis > > > > > > > > > > Digital Golem > > > > > > > > > > > > > > > > > > > > > On 7 May 2015, at 22:11, > > > > > > > > > > > Stephen Blair <[email protected] > > > > > > > > > > > <mailto:[email protected]> > wrote: > > > > > > > > > > > > > > > > > > > > > > > > On Thu, May 7, 2015 at 1:40 PM, Jean-Louis Billard > > > > > > <[email protected] <mailto:[email protected]> > wrote: > > > > > > > > > > > > > Hi all, > > > > > > > > > > > > > > The installer for 2015SP1 tells me that > > > > > > > Softimage was not installed properly and the log shows these > > > > > > > culprits: > > > > > > > > > > > > > > Error: Application/bin/cmdreg -f > > > > > > > "Application/bin/XSICOMDLLs.lst" > > > > > > > Error: Application/bin/cmdreg -f > > > > > > > "Application/Plugins/PLUGINSCOMDLLs.lst” > > > > > > > > > > > > > > > > > > > > > > > > > Try running those commands yourself. On CentOS 6.5, > > > > > > I was getting a core dump until I ran them. > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > >
