Check if your OBP firmware is latest. Il 02/dic/2015 03:57 PM, "richard" <richardbrit...@hotmail.co.uk> ha scritto:
> Hi all: > > I’m installing 5.8 64 bit on a SunSparc 5240 with an array of 10 disks. > > If I boot into Solaris the array takes a while to initialise, but > eventually gets there and then I get a Solaris environment. > > When I boot the install58 CD I get an OpenBSD setup environment, but when > it gets to the ‘which disk would you like to use’ question the options are… > ‘none’ – i.e. no disk found. > > I’m assuming that the install CD does not have the driver for the array, > but so far as I can tell other folk have managed to install on similar > boxes. > > Is there an alternative boot image with different drivers? > > Do I need to do something at the monitor prompt or OpenBSD shell to > initialise the array? > > Output of dmesg from OpenBSD shell follows. > > Many thanks, Richard. > > > ###### begin dmesg output ###### > # dmesg > console is /virtual-devices@100/console@1 > Copyright (c) 1982, 1986, 1989, 1991, 1993 > The Regents of the University of California. All rights reserved. > Copyright (c) 1995-2015 OpenBSD. All rights reserved. > http://www.OpenBSD.org > > OpenBSD 5.8 (RAMDISK) #631: Sun Aug 16 06:08:02 MDT 2015 > dera...@sparc64.openbsd.org:/usr/src/sys/arch/sparc64/compile/RAMDISK > real mem = 4294967296 (4096MB) > avail mem = 4205748224 (4010MB) > mainbus0 at root: T5240 > cpu0 at mainbus0: SUNW,UltraSPARC-T2+ (rev 0.0) @ 1415.108 MHz > "SUNW,UltraSPARC-T2+" at mainbus0 not configured > "SUNW,UltraSPARC-T2+" at mainbus0 not configured > "SUNW,UltraSPARC-T2+" at mainbus0 not configured > "SUNW,UltraSPARC-T2+" at mainbus0 not configured > "SUNW,UltraSPARC-T2+" at mainbus0 not configured > "SUNW,UltraSPARC-T2+" at mainbus0 not configured > "SUNW,UltraSPARC-T2+" at mainbus0 not configured > vbus0 at mainbus0 > "flashprom" at vbus0 not configured > "tpm" at vbus0 not configured > "n2cp" at vbus0 not configured > "ncp" at vbus0 not configured > vrng0 at vbus0 > vcons0 at vbus0: ivec 0x111, console > cbus0 at vbus0 > "virtual-channel" at cbus0 not configured > "virtual-channel" at cbus0 not configured > "virtual-console-concentrator" at cbus0 not configured > "virtual-network-switch" at cbus0 not configured > "virtual-disk-server" at cbus0 not configured > "virtual-channel-client" at cbus0 not configured > "virtual-channel-client" at cbus0 not configured > "virtual-domain-service" at cbus0 not configured > vrtc0 at vbus0 > vpci0 at mainbus0: bus 2 to 9, dvma map 80000000-ffffffff > pci0 at vpci0 > ppb0 at pci0 dev 0 function 0 "PLX PEX 8548" rev 0xaa > pci1 at ppb0 bus 3 > ppb1 at pci1 dev 1 function 0 "PLX PEX 8548" rev 0xaa > pci2 at ppb1 bus 4 > ppb2 at pci2 dev 0 function 0 "PLX PEX 8112" rev 0xaa > pci3 at ppb2 bus 5 > ohci0 at pci3 dev 0 function 0 "NEC USB" rev 0x43: ivec 0x415, version 1.0 > ohci1 at pci3 dev 0 function 1 "NEC USB" rev 0x43: ivec 0x416, version 1.0 > ehci0 at pci3 dev 0 function 2 "NEC USB" rev 0x04: ivec 0x417 > usb0 at ehci0: USB revision 2.0 > uhub0 at usb0 "NEC EHCI root hub" rev 2.00/1.00 addr 1 > usb1 at ohci0: USB revision 1.0 > uhub1 at usb1 "NEC OHCI root hub" rev 1.00/1.00 addr 1 > usb2 at ohci1: USB revision 1.0 > uhub2 at usb2 "NEC OHCI root hub" rev 1.00/1.00 addr 1 > ppb3 at pci1 dev 8 function 0 "PLX PEX 8548" rev 0xaa > pci4 at ppb3 bus 6 > mpi0 at pci4 dev 0 function 0 "Symbios Logic SAS1068E" rev 0x04: msi > mpi0: UNUSED, firmware 1.27.0.0 > scsibus0 at mpi0: 112 targets > ppb4 at pci1 dev 9 function 0 "PLX PEX 8548" rev 0xaa: msi > pci5 at ppb4 bus 7 > ppb5 at pci1 dev 12 function 0 "PLX PEX 8548" rev 0xaa: msi > pci6 at ppb5 bus 8 > "Adaptec ASR-2200S" rev 0x09 at pci6 dev 0 function 0 not configured > ppb6 at pci1 dev 13 function 0 "PLX PEX 8548" rev 0xaa: msi > pci7 at ppb6 bus 9 > ebus0 at mainbus0 > com0 at ebus0 addr ca0000-ca0007 ivec 0x13: ns16550a, 16 byte fifo > "pci-performance-counters" at mainbus0 not configured > vpci1 at mainbus0: bus 2 to 7, dvma map 80000000-ffffffff > pci8 at vpci1 > ppb7 at pci8 dev 0 function 0 "PLX PEX 8548" rev 0xaa > pci9 at ppb7 bus 3 > ppb8 at pci9 dev 8 function 0 "PLX PEX 8548" rev 0xaa > pci10 at ppb8 bus 4 > "Sun Neptune" rev 0x01 at pci10 dev 0 function 0 not configured > "Sun Neptune" rev 0x01 at pci10 dev 0 function 1 not configured > "Sun Neptune" rev 0x01 at pci10 dev 0 function 2 not configured > "Sun Neptune" rev 0x01 at pci10 dev 0 function 3 not configured > ppb9 at pci9 dev 9 function 0 "PLX PEX 8548" rev 0xaa: msi > pci11 at ppb9 bus 5 > ppb10 at pci9 dev 12 function 0 "PLX PEX 8548" rev 0xaa: msi > pci12 at ppb10 bus 6 > ppb11 at pci9 dev 13 function 0 "PLX PEX 8548" rev 0xaa: msi > pci13 at ppb11 bus 7 > "pci-performance-counters" at mainbus0 not configured > uhub3 at uhub0 port 4 "vendor 0x04b4 product 0x6560" rev 2.00/0.0b addr 2 > umass0 at uhub3 port 4 configuration 1 interface 0 "OEM Mass Storage plus" > rev 3 > umass0: using SCSI over Bulk-Only > scsibus1 at umass0: 2 targets, initiator 0 > cd0 at scsibus1 targ 1 lun 0: <TEAC, DV-W28SS-R, 1.0C> SCSI0 5/cdrom > removable 9 > uhidev0 at uhub3 port 4 configuration 1 interface 1 "OEM Mass Storage > plus" rev3 > uhidev0: iclass 3/0 > uhid at uhidev0 not configured > softraid0 at root > scsibus2 at softraid0: 256 targets > bootpath: /pci@400,0/pci@0,0/pci@1,0/pci@0,0/usb@0,2/hub@4,0/device@4 > ,0/storagef > root on rd0a swap on rd0b dump on rd0b > ###### end dmesg output ###### > >
