On Friday 28 December 2001 3:10 am, you wrote: > Hi all, > > I am trying to configure my USB speedtouch on NetBSD and have easily > managed to get the device working etc etc, but I am unable to dial in to my > ISP. > > The connection works under windows, and my provider is very specific that > PAP must be the only authentication protocol used. > > I don't know a lot about ppp on *BSD, so I have a couple of questions: > > In Windows, I have to put a phone number in to dial up on my adsl modem. Do > I have to enter this number somewhere on my NetBSD box? None of the doco I > have found has any provision for it. Do I have to configure a ppp.secret > file or a pap-secrets file? Neither of these seems to make a difference > (unless I have configured them icorrectly...??). > > Can anyone give me an idea of what I might have configured incorrectly? > Below is my config and log file from when I attempt to connect. > > Thanks in advance > JP > > default: > > set log Phase Chat IPCP CCP tun command > > adsl: > set authname [EMAIL PROTECTED] > set authkey notmypassword > set device !"pppoa2 -vpi 8 -vci 35 -d /dev/ugen0 -v 1" > deny chap > disable chap > enable pap > accept pap > set speed sync > set timeout 0 > enable lqr > set lqrperiod 5 > set redial 15 10000 > set dial "" > set ifaddr 10.0.0.1/0 10.0.0.2/0 255.255.255.0 0.0.0.0 > add default HISADDR > enable dns > > > > Dec 29 00:11:15 fw01 /netbsd: tun0: not multicast capable, IPv6 not enabled > Dec 29 00:11:15 fw01 ppp[220]: Phase: Using interface: tun0 > Dec 29 00:11:15 fw01 ppp[220]: Phase: deflink: Created in closed state > Dec 29 00:11:15 fw01 ppp[220]: tun0: Command: adsl: set authname > [EMAIL PROTECTED] Dec 29 00:11:15 fw01 ppp[220]: tun0: Command: > adsl: set authkey ******** Dec 29 00:11:15 fw01 ppp[220]: tun0: Command: > adsl: set device !pppoa2 -vpi 8 -vci 35 -d /dev/ugen0 -v 1 Dec 29 00:11:15 > fw01 ppp[220]: tun0: Command: adsl: deny chap > Dec 29 00:11:15 fw01 ppp[220]: tun0: Command: adsl: disable chap > Dec 29 00:11:15 fw01 ppp[220]: tun0: Command: adsl: enable pap > Dec 29 00:11:15 fw01 ppp[220]: tun0: Command: adsl: accept pap > Dec 29 00:11:15 fw01 ppp[220]: tun0: Command: adsl: set speed sync > Dec 29 00:11:15 fw01 ppp[220]: tun0: Command: adsl: set timeout 0 > Dec 29 00:11:15 fw01 ppp[220]: tun0: Command: adsl: enable lqr > Dec 29 00:11:15 fw01 ppp[220]: tun0: Command: adsl: set lqrperiod 5 > Dec 29 00:11:15 fw01 ppp[220]: tun0: Command: adsl: set redial 15 10000 > Dec 29 00:11:15 fw01 ppp[220]: tun0: Command: adsl: set dial > Dec 29 00:11:15 fw01 ppp[220]: tun0: Command: adsl: set ifaddr 10.0.0.1/0 > 10.0.0.2/0 255.255.255.0 0.0.0.0 Dec 29 00:11:15 fw01 ppp[220]: tun0: > Command: adsl: add default HISADDR Dec 29 00:11:15 fw01 ppp[220]: tun0: > Command: adsl: enable dns > Dec 29 00:11:15 fw01 ppp[221]: tun0: Phase: PPP Started (background mode). > Dec 29 00:11:15 fw01 ppp[221]: tun0: Phase: bundle: Establish > Dec 29 00:11:15 fw01 ppp[221]: tun0: Phase: deflink: closed -> opening > Dec 29 00:11:15 fw01 pppoa2[223]: Starting PPPoA2 ( merged version includes > new ATM/AAL5 stack ) 1_0 Dec 29 00:11:15 fw01 ppp[221]: tun0: Phase: > deflink: Connected! > Dec 29 00:11:15 fw01 pppoa2[223]: I'm the parent process, I handle the > endpoint 0x07 Dec 29 00:11:15 fw01 ppp[221]: tun0: Phase: deflink: opening > -> dial Dec 29 00:11:15 fw01 pppoa2[223]: pty descriptors : fdin=3, fdout=4 > Dec 29 00:11:15 fw01 ppp[221]: tun0: Chat: deflink: Dial attempt 1 of 10000 > Dec 29 00:11:15 fw01 pppoa2[223]: Increasing SNDBUF from 2048 to 65536 Dec > 29 00:11:15 fw01 pppoa2[223]: Increasing RCVBUF from 4096 to 65536 Dec 29 > 00:11:15 fw01 ppp[221]: tun0: Phase: deflink: dial -> carrier Dec 29 > 00:11:15 fw01 ppp[221]: tun0: Phase: deflink: carrier -> login Dec 29 > 00:11:15 fw01 ppp[221]: tun0: Phase: deflink: login -> lcp > Dec 29 00:11:15 fw01 pppoa2[224]: I'm the children process, I handle the > endpoint 0x87 Dec 29 00:11:31 fw01 ppp[221]: tun0: Phase: deflink: > Disconnected! Dec 29 00:11:31 fw01 ppp[221]: tun0: Phase: deflink: lcp -> > logout Dec 29 00:11:31 fw01 ppp[221]: tun0: Phase: deflink: logout -> > hangup Dec 29 00:11:31 fw01 ppp[221]: tun0: Phase: deflink: Disconnected! > Dec 29 00:11:31 fw01 ppp[221]: tun0: Phase: deflink: Connect time: 16 secs: > 0 octets in, 150 octets out Dec 29 00:11:31 fw01 ppp[221]: tun0: Phase: > deflink: : 0 packets in, 5 packets out Dec 29 00:11:31 fw01 ppp[221]: tun0: > Phase: total 9 bytes/sec, peak 12 bytes/sec on Sat Dec 29 00:11:19 2001 > Dec 29 00:11:31 fw01 ppp[221]: tun0: Phase: deflink: HUPing 223 > Dec 29 00:11:31 fw01 pppoa2[223]: Killed by a signal 1 > Dec 29 00:11:31 fw01 ppp[221]: tun0: Phase: deflink: hangup -> closed > Dec 29 00:11:31 fw01 ppp[221]: tun0: Phase: bundle: Dead > Dec 29 00:11:31 fw01 ppp[221]: tun0: Phase: PPP Terminated (normal). > Dec 29 00:11:31 fw01 ppp[221]: tun0: Chat: Parent notified of failure > Dec 29 00:11:31 fw01 ppp[220]: tun0: Phase: Parent: Child failed (errdead) > > > Liste de diffusion modem ALCATEL SpeedTouch USB > Pour se désinscrire : > mailto:[EMAIL PROTECTED]?subject=unsubscribe
Alright man, Well i had similar questions myself so ill tell u what i found out but i dont use netbsd. First the number for adsl is a crock its not real. DUN of windows requires a number thats the only reason why theres a number supplied but the actual adsl connection doesnt use a number if u change the windows no. to 0 it would still connect you. im not sure about netbsd but on my linux box the file dealin with pap passwords is /etc/ppp/pap-secrets you need to add a line like this <your_username> * <your_password> you can also add this line to chap_secrets because it'll try both and connect with the one that connects. also why is ifaddress assigning local ip addresses try hashing that line out im not sure if you need it or not. v Liste de diffusion modem ALCATEL SpeedTouch USB Pour se désinscrire : mailto:[EMAIL PROTECTED]?subject=unsubscribe
