I am still not able to init my modem. Here are the
steps I have followed.
1. Installed the Redhat 7.2 on my compaq presario with
an OHCI USB chipset using install CDs 1 & 2 from
redhat.
2. Booted Machine with Modem connected. Both leds
turn green as soon as OHCI driver is loaded.
Here is a copy of my /proc/bus/usb/devices:
T: Bus=01 Lev=00 Prnt=00 Port=00 Cnt=00 Dev#= 1
Spd=12 MxCh= 2
B: Alloc= 0/900 us ( 0%), #Int= 0, #Iso= 0
D: Ver= 1.10 Cls=09(hub ) Sub=00 Prot=00 MxPS= 8
#Cfgs= 1
P: Vendor=0000 ProdID=0000 Rev= 0.00
S: Product=USB OHCI Root Hub
S: SerialNumber=c484a000
C:* #Ifs= 1 Cfg#= 1 Atr=40 MxPwr= 0mA
I: If#= 0 Alt= 0 #EPs= 1 Cls=09(hub ) Sub=00 Prot=00
Driver=hub
E: Ad=81(I) Atr=03(Int.) MxPS= 2 Ivl=255ms
T: Bus=01 Lev=01 Prnt=01 Port=01 Cnt=01 Dev#= 3
Spd=12 MxCh= 0
D: Ver= 1.10 Cls=ff(vend.) Sub=00 Prot=00 MxPS= 8
#Cfgs= 1
P: Vendor=06b9 ProdID=4061 Rev= 0.00
S: Manufacturer=ALCATEL
S: Product=Speed Touch USB
S: SerialNumber=0090D02DB8E9
C:* #Ifs= 3 Cfg#= 1 Atr=80 MxPwr=500mA
I: If#= 0 Alt= 0 #EPs= 1 Cls=ff(vend.) Sub=00 Prot=00
Driver=usbdevfs
E: Ad=81(I) Atr=03(Int.) MxPS= 16 Ivl= 50ms
I: If#= 1 Alt= 0 #EPs= 0 Cls=ff(vend.) Sub=00 Prot=00
Driver=usbdevfs
I: If#= 1 Alt= 1 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00
Driver=usbdevfs
E: Ad=06(O) Atr=02(Bulk) MxPS= 64 Ivl= 0ms
E: Ad=07(O) Atr=02(Bulk) MxPS= 64 Ivl= 0ms
E: Ad=87(I) Atr=02(Bulk) MxPS= 64 Ivl= 0ms
I: If#= 1 Alt= 2 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00
Driver=usbdevfs
E: Ad=06(O) Atr=02(Bulk) MxPS= 32 Ivl= 0ms
E: Ad=07(O) Atr=02(Bulk) MxPS= 32 Ivl= 0ms
E: Ad=87(I) Atr=02(Bulk) MxPS= 64 Ivl= 0ms
I: If#= 1 Alt= 3 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00
Driver=usbdevfs
E: Ad=06(O) Atr=02(Bulk) MxPS= 16 Ivl= 0ms
E: Ad=07(O) Atr=02(Bulk) MxPS= 16 Ivl= 0ms
E: Ad=87(I) Atr=02(Bulk) MxPS= 64 Ivl= 0ms
I: If#= 2 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=00 Prot=00
Driver=usbdevfs
E: Ad=05(O) Atr=02(Bulk) MxPS= 8 Ivl= 0ms
E: Ad=85(I) Atr=02(Bulk) MxPS= 8 Ivl= 0ms
3. I extracted the mgmt.o from speedmgt.tar.gz onto my
/root/downloads/mgmt
Did NOT install or compile
4. I extracted speedtouch-1_0.tar.gz(Benoit) and
performed
./configure
make
make install
All steps passed.
5. Just to see if I can get modem to sync I did:
/usr/bin/local/modem_run -m -f
/root/downloads/mgmt/mgmt.o
Modem leds turn off momentarily and then left one
is solid green while the right one blinks green most
of the time with a red blink once in a while.
I did this just to see if I get sync and didnt want to
worry about all the PPP stuff. In the past I have done
the fully HOWTO that Benoit suggest. Also could NOT
get sync.
My modem works with another computer running under
windows. The rj11 jack and cord work as well.
Here is a copy of my log:
Feb 6 13:11:01 localhost syslogd 1.4.1: restart.
Feb 6 13:11:01 localhost syslog: syslogd startup
succeeded
Feb 6 13:11:01 localhost syslog: klogd startup
succeeded
Feb 6 13:11:01 localhost kernel: klogd 1.4.1, log
source = /proc/kmsg started.
Feb 6 13:11:01 localhost kernel: Inspecting
/boot/System.map-2.4.7-10
Feb 6 13:11:02 localhost portmap: portmap startup
succeeded
Feb 6 13:11:02 localhost rpc.statd[715]: Version
0.3.1 Starting
Feb 6 13:11:03 localhost nfslock: rpc.statd startup
succeeded
Feb 6 13:11:03 localhost kernel: Loaded 15046 symbols
from /boot/System.map-2.4.7-10.
Feb 6 13:11:03 localhost kernel: Symbols match kernel
version 2.4.7.
Feb 6 13:11:03 localhost kernel: Loaded 115 symbols
from 6 modules.
Feb 6 13:11:03 localhost kernel: Linux version
2.4.7-10 ([EMAIL PROTECTED]) (gcc
version 2.96 20000731 (Red Hat Linux 7.1 2.96-98)) #1
Thu Sep 6 17:27:27 EDT 2001
Feb 6 13:11:03 localhost kernel: BIOS-provided
physical RAM map:
Feb 6 13:11:03 localhost kernel: BIOS-e820:
0000000000000000 - 000000000009fc00 (usable)
Feb 6 13:11:03 localhost kernel: BIOS-e820:
000000000009fc00 - 00000000000a0000 (reserved)
Feb 6 13:11:03 localhost kernel: BIOS-e820:
00000000000f0000 - 0000000000100000 (reserved)
Feb 6 13:11:03 localhost kernel: BIOS-e820:
0000000000100000 - 0000000003bf0000 (usable)
Feb 6 13:11:03 localhost kernel: BIOS-e820:
0000000003bf0000 - 0000000003bf3000 (ACPI NVS)
Feb 6 13:11:03 localhost kernel: BIOS-e820:
0000000003bf3000 - 0000000003c00000 (ACPI data)
Feb 6 13:11:03 localhost kernel: BIOS-e820:
00000000ffff0000 - 0000000100000000 (reserved)
Feb 6 13:11:03 localhost kernel: Scanning bios EBDA
for MXT signature
Feb 6 13:11:03 localhost kernel: On node 0
totalpages: 15344
Feb 6 13:11:03 localhost kernel: zone(0): 4096 pages.
Feb 6 13:11:03 localhost kernel: zone(1): 11248
pages.
Feb 6 13:11:03 localhost kernel: zone(2): 0 pages.
Feb 6 13:11:03 localhost kernel: Kernel command line:
auto BOOT_IMAGE=linux ro root=302
BOOT_FILE=/boot/vmlinuz-2.4.7-10
Feb 6 13:11:03 localhost kernel: Initializing CPU#0
Feb 6 13:11:03 localhost keytable: Loading keymap:
succeeded
Feb 6 13:11:03 localhost kernel: Detected 250.069 MHz
processor.
Feb 6 13:09:42 localhost rc.sysinit: Mounting proc
filesystem: succeeded
Feb 6 13:11:03 localhost kernel: Console: colour VGA+
80x25
Feb 6 13:09:42 localhost rc.sysinit: Unmounting
initrd: succeeded
Feb 6 13:11:04 localhost keytable: Loading system
font: succeeded
Feb 6 13:11:04 localhost kernel: Calibrating delay
loop... 498.07 BogoMIPS
Feb 6 13:09:42 localhost sysctl: net.ipv4.ip_forward
= 0
Feb 6 13:11:04 localhost kernel: Memory:
57216k/61376k available (1269k kernel code, 3420k
reserved, 90k data, 220k init, 0k highmem)
Feb 6 13:09:42 localhost sysctl:
net.ipv4.conf.default.rp_filter = 1
Feb 6 13:11:04 localhost kernel: Checking if this
processor honours the WP bit even in supervisor
mode... Ok.
Feb 6 13:09:42 localhost sysctl: kernel.sysrq = 0
Feb 6 13:11:04 localhost kernel: Dentry-cache hash
table entries: 8192 (order: 4, 65536 bytes)
Feb 6 13:11:04 localhost random: Initializing random
number generator: succeeded
Feb 6 13:09:42 localhost rc.sysinit: Configuring
kernel parameters: succeeded
Feb 6 13:11:04 localhost kernel: Inode-cache hash
table entries: 4096 (order: 3, 32768 bytes)
Feb 6 13:09:42 localhost date: Wed Feb 6 13:09:35
EST 2002
Feb 6 13:11:04 localhost kernel: Mount-cache hash
table entries: 1024 (order: 1, 8192 bytes)
Feb 6 13:09:42 localhost rc.sysinit: Setting clock
(localtime): Wed Feb 6 13:09:35 EST 2002 succeeded
Feb 6 13:11:05 localhost kernel: Buffer-cache hash
table entries: 1024 (order: 0, 4096 bytes)
Feb 6 13:09:42 localhost rc.sysinit: Loading default
keymap succeeded
Feb 6 13:11:05 localhost kernel: Page-cache hash
table entries: 16384 (order: 5, 131072 bytes)
Feb 6 13:09:42 localhost rc.sysinit: Setting default
font (lat0-sun16): succeeded
Feb 6 13:11:06 localhost netfs: Mounting other
filesystems: succeeded
Feb 6 13:09:42 localhost rc.sysinit: Activating swap
partitions: succeeded
Feb 6 13:09:42 localhost rc.sysinit: Setting hostname
localhost.localdomain: succeeded
Feb 6 13:09:42 localhost rc.sysinit: Mounting USB
filesystem: succeeded
Feb 6 13:11:06 localhost apmd[827]: Version 3.0final
(APM BIOS 1.2, Linux driver 1.14)
Feb 6 13:11:06 localhost apmd: apmd startup succeeded
Feb 6 13:09:42 localhost rc.sysinit: Initializing USB
controller (usb-ohci): succeeded
Feb 6 13:11:07 localhost kernel: CPU: Cyrix M II 2.5x
Core/Bus Clock stepping 04
Feb 6 13:11:07 localhost apmd[827]: Charge: * * *
(-1% unknown)
Feb 6 13:09:42 localhost fsck: /: clean, 80348/496992
files, 318717/992013 blocks
Feb 6 13:09:42 localhost rc.sysinit: Checking root
filesystem succeeded
Feb 6 13:09:42 localhost rc.sysinit: Remounting root
filesystem in read-write mode: succeeded
Feb 6 13:11:07 localhost kernel: Checking 'hlt'
instruction... OK.
Feb 6 13:11:08 localhost kernel: POSIX conformance
testing by UNIFIX
Feb 6 13:11:08 localhost kernel: mtrr: v1.40
(20010327) Richard Gooch ([EMAIL PROTECTED])
Feb 6 13:09:43 localhost rc.sysinit: Finding module
dependencies: succeeded
Feb 6 13:09:44 localhost fsck: /boot: clean, 31/12048
files, 7320/48163 blocks
Feb 6 13:09:44 localhost rc.sysinit: Checking
filesystems succeeded
Feb 6 13:11:08 localhost autofs: automount startup
succeeded
Feb 6 13:09:44 localhost rc.sysinit: Mounting local
filesystems: succeeded
Feb 6 13:11:08 localhost kernel: mtrr: detected mtrr
type: Cyrix ARR
Feb 6 13:09:44 localhost rc.sysinit: Enabling local
filesystem quotas: succeeded
Feb 6 13:11:08 localhost kernel: PCI: PCI BIOS
revision 2.10 entry at 0xfb4c0, last bus=1
Feb 6 13:09:45 localhost rc.sysinit: Enabling swap
space: succeeded
Feb 6 13:11:08 localhost kernel: PCI: Using
configuration type 1
Feb 6 13:09:48 localhost init: Entering runlevel: 5
Feb 6 13:11:09 localhost kernel: PCI: Probing PCI
hardware
Feb 6 13:09:49 localhost kudzu: Updating /etc/fstab
succeeded
Feb 6 13:11:09 localhost kernel: PCI: Using IRQ
router SIS [1039/0008] at 00:01.0
Feb 6 13:09:57 localhost kudzu: succeeded
Feb 6 13:11:09 localhost kernel: isapnp: Scanning for
PnP cards...
Feb 6 13:09:57 localhost ipchains: Flushing all
current rules and user defined chains: succeeded
Feb 6 13:11:09 localhost kernel: isapnp: No Plug &
Play device found
Feb 6 13:09:57 localhost ipchains: Clearing all
current rules and user defined chains: succeeded
Feb 6 13:11:09 localhost kernel: Linux NET4.0 for
Linux 2.4
Feb 6 13:09:58 localhost ipchains: Applying ipchains
firewall rules succeeded
Feb 6 13:11:10 localhost kernel: Based upon Swansea
University Computer Society NET3.039
Feb 6 13:09:59 localhost sysctl: net.ipv4.ip_forward
= 0
Feb 6 13:11:10 localhost kernel: Initializing RT
netlink socket
Feb 6 13:09:59 localhost sysctl:
net.ipv4.conf.default.rp_filter = 1
Feb 6 13:09:59 localhost sysctl: kernel.sysrq = 0
Feb 6 13:09:59 localhost network: Setting network
parameters: succeeded
Feb 6 13:10:00 localhost network: Bringing up
interface lo: succeeded
Feb 6 13:11:10 localhost kernel: apm: BIOS version
1.2 Flags 0x07 (Driver version 1.14)
Feb 6 13:11:11 localhost kernel: mxt_scan_bios: enter
Feb 6 13:10:01 localhost ifup: Determining IP
information for eth0...
Feb 6 13:11:11 localhost kernel: Starting kswapd v1.8
Feb 6 13:11:11 localhost kernel: VFS: Diskquotas
version dquot_6.5.0 initialized
Feb 6 13:11:01 localhost dhcpcd[633]: timed out
waiting for a valid DHCP server response
Feb 6 13:11:11 localhost kernel: pty: 2048 Unix98
ptys configured
Feb 6 13:11:11 localhost kernel: Serial driver
version 5.05c (2001-07-08) with MANY_PORTS MULTIPORT
SHARE_IRQ SERIAL_PCI ISAPNP enabled
Feb 6 13:11:01 localhost ifup: failed.
Feb 6 13:11:11 localhost kernel: ttyS00 at 0x03f8
(irq = 4) is a 16550A
Feb 6 13:11:11 localhost kernel: Real Time Clock
Driver v1.10d
Feb 6 13:11:01 localhost network: Bringing up
interface eth0: failed
Feb 6 13:11:11 localhost kernel: block: queued
sectors max/low 37941kB/12647kB, 128 slots per queue
Feb 6 13:11:11 localhost kernel: RAMDISK driver
initialized: 16 RAM disks of 4096K size 1024 blocksize
Feb 6 13:11:12 localhost kernel: Uniform
Multi-Platform E-IDE driver Revision: 6.31
Feb 6 13:11:12 localhost kernel: ide: Assuming 33MHz
PCI bus speed for PIO modes; override with idebus=xx
Feb 6 13:11:12 localhost kernel: SIS5513: IDE
controller on PCI bus 00 dev 01
Feb 6 13:11:12 localhost kernel: SIS5513: chipset
revision 208
Feb 6 13:11:12 localhost kernel: SIS5513: not 100%%
native mode: will probe irqs later
Feb 6 13:11:12 localhost kernel: SiS530
Feb 6 13:11:12 localhost kernel: ide0: BM-DMA at
0x4000-0x4007, BIOS settings: hda:DMA, hdb:DMA
Feb 6 13:11:12 localhost kernel: ide1: BM-DMA at
0x4008-0x400f, BIOS settings: hdc:DMA, hdd:DMA
Feb 6 13:11:12 localhost kernel: hda: ST34311A, ATA
DISK drive
Feb 6 13:11:12 localhost kernel: hdb: LTN323, ATAPI
CD/DVD-ROM drive
Feb 6 13:11:12 localhost kernel: ide0 at
0x1f0-0x1f7,0x3f6 on irq 14
Feb 6 13:11:12 localhost kernel: hda: 8421840 sectors
(4312 MB) w/256KiB Cache, CHS=524/255/63, UDMA(66)
Feb 6 13:11:12 localhost kernel: ide-floppy driver
0.97
Feb 6 13:11:12 localhost kernel: Partition check:
Feb 6 13:11:12 localhost xinetd: xinetd startup
succeeded
Feb 6 13:11:12 localhost kernel: hda: hda1 hda2 hda3
Feb 6 13:11:12 localhost kernel: Floppy drive(s): fd0
is 1.44M
Feb 6 13:11:12 localhost kernel: FDC 0 is a post-1991
82077
Feb 6 13:11:12 localhost xinetd[896]: chargen
disabled, removing
Feb 6 13:11:13 localhost kernel: ide-floppy driver
0.97
Feb 6 13:11:13 localhost xinetd[896]: chargen
disabled, removing
Feb 6 13:11:13 localhost kernel: md: md driver 0.90.0
MAX_MD_DEVS=256, MD_SB_DISKS=27
Feb 6 13:11:13 localhost kernel: md: Autodetecting
RAID arrays.
Feb 6 13:11:13 localhost kernel: md: autorun ...
Feb 6 13:11:13 localhost kernel: md: ... autorun
DONE.
Feb 6 13:11:13 localhost xinetd[896]: daytime
disabled, removing
Feb 6 13:11:13 localhost kernel: NET4: Linux TCP/IP
1.0 for NET4.0
Feb 6 13:11:13 localhost xinetd[896]: daytime
disabled, removing
Feb 6 13:11:13 localhost kernel: IP Protocols: ICMP,
UDP, TCP, IGMP
Feb 6 13:11:13 localhost xinetd[896]: echo disabled,
removing
Feb 6 13:11:13 localhost kernel: IP: routing cache
hash table of 512 buckets, 4Kbytes
Feb 6 13:11:13 localhost xinetd[896]: echo disabled,
removing
Feb 6 13:11:13 localhost kernel: TCP: Hash tables
configured (established 4096 bind 4096)
Feb 6 13:11:13 localhost xinetd[896]: rsync disabled,
removing
Feb 6 13:11:13 localhost kernel: Linux IP multicast
router 0.06 plus PIM-SM
Feb 6 13:11:13 localhost xinetd[896]: time disabled,
removing
Feb 6 13:11:13 localhost kernel: NET4: Unix domain
sockets 1.0/SMP for Linux NET4.0.
Feb 6 13:11:13 localhost xinetd[896]: time disabled,
removing
Feb 6 13:11:13 localhost kernel: RAMDISK: Compressed
image found at block 0
Feb 6 13:11:14 localhost kernel: Freeing initrd
memory: 322k freed
Feb 6 13:11:14 localhost kernel: VFS: Mounted root
(ext2 filesystem).
Feb 6 13:11:14 localhost kernel: Journalled Block
Device driver loaded
Feb 6 13:11:14 localhost kernel: hda: dma_intr:
status=0x51 { DriveReady SeekComplete Error }
Feb 6 13:11:14 localhost kernel: hda: dma_intr:
error=0x84 { DriveStatusError BadCRC }
Feb 6 13:11:14 localhost kernel: hda: dma_intr:
status=0x51 { DriveReady SeekComplete Error }
Feb 6 13:11:14 localhost kernel: hda: dma_intr:
error=0x84 { DriveStatusError BadCRC }
Feb 6 13:11:14 localhost kernel: hda: dma_intr:
status=0x51 { DriveReady SeekComplete Error }
Feb 6 13:11:14 localhost kernel: hda: dma_intr:
error=0x84 { DriveStatusError BadCRC }
Feb 6 13:11:14 localhost kernel: hda: dma_intr:
status=0x51 { DriveReady SeekComplete Error }
Feb 6 13:11:14 localhost kernel: hda: dma_intr:
error=0x84 { DriveStatusError BadCRC }
Feb 6 13:11:14 localhost kernel: ide0: reset: success
Feb 6 13:11:14 localhost kernel: kjournald starting.
Commit interval 5 seconds
Feb 6 13:11:14 localhost kernel: EXT3-fs: mounted
filesystem with ordered data mode.
Feb 6 13:11:14 localhost kernel: Freeing unused
kernel memory: 220k freed
Feb 6 13:11:14 localhost kernel: Adding Swap: 192772k
swap-space (priority -1)
Feb 6 13:11:14 localhost kernel: usb.c: registered
new driver usbdevfs
Feb 6 13:11:14 localhost kernel: usb.c: registered
new driver hub
Feb 6 13:11:14 localhost kernel: usb-ohci.c: USB OHCI
at membase 0xc484a000, IRQ 3
Feb 6 13:11:14 localhost kernel: usb-ohci.c:
usb-00:01.2, Silicon Integrated Systems [SiS] 7001
Feb 6 13:11:14 localhost kernel: usb.c: new USB bus
registered, assigned bus number 1
Feb 6 13:11:14 localhost kernel: hub.c: USB hub found
Feb 6 13:11:14 localhost kernel: hub.c: 2 ports
detected
Feb 6 13:11:14 localhost xinetd[896]: xinetd Version
2.3.3 started with libwrap options compiled in.
Feb 6 13:11:15 localhost kernel: usb-ohci.c: v5.2:USB
OHCI Host Controller Driver
Feb 6 13:11:15 localhost xinetd[896]: Started
working: 1 available service
Feb 6 13:11:15 localhost kernel: hub.c: USB new
device connect on bus1/2, assigned device number 2
Feb 6 13:11:15 localhost kernel: usb.c: USB device 2
(vend/prod 0x6b9/0x4061) is not claimed by any active
driver.
Feb 6 13:11:15 localhost kernel: EXT3 FS 2.4-0.9.8,
25 Aug 2001 on ide0(3,2), internal journal
Feb 6 13:11:15 localhost kernel: kjournald starting.
Commit interval 5 seconds
Feb 6 13:11:15 localhost kernel: EXT3 FS 2.4-0.9.8,
25 Aug 2001 on ide0(3,1), internal journal
Feb 6 13:11:15 localhost kernel: EXT3-fs: mounted
filesystem with ordered data mode.
Feb 6 13:11:15 localhost kernel: 0x378: FIFO is 16
bytes
Feb 6 13:11:15 localhost kernel: 0x378:
writeIntrThreshold is 16
Feb 6 13:11:15 localhost kernel: 0x378:
readIntrThreshold is 16
Feb 6 13:11:15 localhost kernel: parport0: PC-style
at 0x378 (0x778) [PCSPP,TRISTATE,COMPAT,ECP]
Feb 6 13:11:16 localhost kernel: parport0: irq 7
detected
Feb 6 13:11:16 localhost kernel: ip_conntrack (479
buckets, 3832 max)
Feb 6 13:11:16 localhost kernel: 8139too Fast
Ethernet driver 0.9.18a
Feb 6 13:11:16 localhost kernel: PCI: Found IRQ 11
for device 00:0b.0
Feb 6 13:11:16 localhost kernel: eth0: RealTek
RTL8139 Fast Ethernet at 0xc4872000,
00:4f:4e:03:84:1d, IRQ 11
Feb 6 13:11:16 localhost kernel: eth0: Setting
half-duplex based on auto-negotiated partner ability
0000.
Feb 6 13:11:19 localhost sendmail: sendmail startup
succeeded
Feb 6 13:11:20 localhost gpm: gpm startup succeeded
Feb 6 13:11:21 localhost crond: crond startup
succeeded
Feb 6 13:11:23 localhost xfs: listening on port 7100
Feb 6 13:11:23 localhost xfs: xfs startup succeeded
Feb 6 13:11:23 localhost anacron: anacron startup
succeeded
Feb 6 13:11:24 localhost atd: atd startup succeeded
Feb 6 13:11:24 localhost xfs: ignoring font path
element /usr/X11R6/lib/X11/fonts/cyrillic (unreadable)
Feb 6 13:11:24 localhost xfs: ignoring font path
element /usr/X11R6/lib/X11/fonts/local (unreadable)
Feb 6 13:11:24 localhost rc: Starting wine:
succeeded
Feb 6 13:14:02 localhost kernel: usb.c: USB
disconnect on device 2
Feb 6 13:16:28 localhost syslogd 1.4.1: restart.
Feb 6 13:17:35 localhost gdm(pam_unix)[1104]: session
opened for user root by (uid=0)
Feb 6 13:17:48 localhost kernel: solo1: version v0.19
time 17:36:51 Sep 6 2001
Feb 6 13:17:48 localhost kernel: PCI: Found IRQ 5 for
device 00:0f.0
Feb 6 13:17:48 localhost kernel: solo1: joystick port
at 0xe401
Feb 6 13:17:48 localhost modprobe: modprobe: Can't
locate module sound-service-0-0
Feb 6 13:17:50 localhost kernel: hub.c: USB new
device connect on bus1/2, assigned device number 3
Feb 6 13:17:50 localhost kernel: usb.c: USB device 3
(vend/prod 0x6b9/0x4061) is not claimed by any active
driver.
Feb 6 13:17:50 localhost /etc/hotplug/usb.agent: ...
no drivers for USB product 6b9/4061/0
Feb 6 13:17:56 localhost gnome-name-server[4000]:
starting
Feb 6 13:17:56 localhost gnome-name-server[4002]:
starting
Feb 6 13:17:56 localhost gnome-name-server[4000]:
name server starting
Feb 6 13:17:56 localhost kernel: ide-floppy driver
0.97
Feb 6 13:17:56 localhost gnome-name-server[4002]:
name server was running on display, exiting
Feb 6 13:17:57 localhost kernel: hdb: ATAPI 32X
CD-ROM drive, 120kB Cache, DMA
Feb 6 13:17:57 localhost kernel: Uniform CD-ROM
driver Revision: 3.12
Feb 6 13:18:03 localhost gconfd (root-4094): starting
(version 1.0.4), pid 4094 user 'root'
Feb 6 13:18:03 localhost gconfd (root-4094):
Successfully registered `OAFIID:gconfd:19991118'
Feb 6 13:18:03 localhost gconfd (root-4094): Unable
to open saved state file '/root/.gconfd/saved_state':
No such file or directory
Feb 6 13:18:08 localhost kernel: cdrom: This disc
doesn't have any tracks I recognize!
Feb 6 13:18:09 localhost xinetd[4181]: warning: can't
get client address: Transport endpoint is not
connected
Feb 6 13:18:33 localhost kernel: cdrom: This disc
doesn't have any tracks I recognize!
Feb 6 13:18:34 localhost xinetd[4595]: warning: can't
get client address: Transport endpoint is not
connected
Feb 6 13:23:03 localhost gconfd (root-4094): 20 items
remain in the cache after cleaning already-synced
items older than 300 seconds
Feb 6 13:55:37 localhost kernel:
usb_control/bulk_msg: timeout
Feb 6 13:55:37 localhost kernel: usbdevfs:
USBDEVFS_BULK failed dev 3 ep 0x85 len 512 ret -110
Feb 6 13:55:39 localhost kernel:
usb_control/bulk_msg: timeout
Feb 6 13:56:10 localhost last message repeated 3
times
Feb 6 13:58:54 localhost last message repeated 6
times
Feb 6 13:59:56 localhost last message repeated 6
times
Feb 6 14:02:09 localhost last message repeated 4
times
Feb 6 14:03:10 localhost last message repeated 6
times
Feb 6 14:05:44 localhost last message repeated 6
times
Feb 6 14:06:46 localhost last message repeated 5
times
Feb 6 14:09:40 localhost last message repeated 6
times
Feb 6 14:10:41 localhost last message repeated 6
times
Feb 6 14:11:43 localhost last message repeated 6
times
Feb 6 14:14:07 localhost last message repeated 4
times
Feb 6 14:15:08 localhost last message repeated 4
times
Feb 6 14:16:10 localhost last message repeated 6
times
Feb 6 14:17:11 localhost last message repeated 6
times
Feb 6 14:19:35 localhost last message repeated 3
times
Feb 6 14:20:36 localhost last message repeated 4
times
Feb 6 14:21:37 localhost last message repeated 6
times
Again, all I have done is simply start with a brand
new installation of Redhat 7.2 and copy and install
the drivers above. I have not patched anything,
complied any kernel, or nothing.
I have tried lots of things, but I think I am just
trying to accomplish SYNC here.
Am I missing a step?
Should the ppp modules be loaded?
Your help is greatly appreciated.
Thank you,
Ozzy
__________________________________________________
Do You Yahoo!?
Send FREE Valentine eCards with Yahoo! Greetings!
http://greetings.yahoo.com
Liste de diffusion modem ALCATEL SpeedTouch USB
Pour se d�sinscrire : mailto:[EMAIL PROTECTED]?subject=unsubscribe
