hi again.. sorry for the incomplete question... it was late...
so here we go..
#modem_run -f /usr/local/libdata/mgmt.o -m
modem_run.log:
Oct 27 16:24:28 Prostotnic1 modem_run[1040]: modem_run version 1.2-beta2
started by magny uid 0
Oct 27 16:24:34 Prostotnic1 modem_run[1040]: Kernel mode driver not found
Oct 27 16:25:25 Prostotnic1 modem_run[1040]: ADSL synchronization has been
obtained
Oct 27 16:25:25 Prostotnic1 modem_run[1040]: ADSL line is up (2400 kbit/s
down | 768 kbit/s up)
# pppoa3 -b -e 1 -v 1 -vpi 8 -vci 35 -c
pppoa3.log:
Oct 27 16:19:30 Prostotnic1 pppoa3[945]: pppoa3 version 1.2-beta2 started by
magny (uid 0)
Oct 27 16:19:30 Prostotnic1 pppoa3[945]: Control thread ready
Oct 27 16:19:30 Prostotnic1 pppoa3[945]: Modem found!
Oct 27 16:19:30 Prostotnic1 pppoa3[945]: pusb_set_configuration 1
and the process is terminated but the /var/run/pppoa3-modem1.pid are still
showing the killed process.
so when I try to start pppoa3 again it shows:
Oct 27 16:20:32 Prostotnic1 pppoa3[952]: A previous instance seems to be
running
Oct 27 16:20:32 Prostotnic1 pppoa3[952]: Sending the kill signal to 945 and
waiting...
but no process with pid 945 is running.
and when I manually kill the new process that only waits and remove the pid
file and restart pppoa3
I got a kernel panic...
ifconfig gives me:
tap0: flags=8802<BROADCAST,SIMPLEX,MULTICAST> mtu 1500
ether 00:bd:5e:99:09:00
but without a active process attached
I reed in the ugen man file, that:
USB_SET_CONFIG:
This operation can only be performed when the control endpoint is
the sole open endpoint.
This is only set for the -e 1 (speedtouch 330 modem) right?
what is the difference between speedtouch 330 and the usual USB modem that
makes it necessary to set that?
without the -e 1, I get in pppoa3.lib:
Oct 27 16:46:08 Prostotnic1 pppoa3[589]: pppoa3 version 1.2-beta2 started by
magny (uid 0)
Oct 27 16:46:08 Prostotnic1 pppoa3[589]: Control thread ready
Oct 27 16:46:08 Prostotnic1 pppoa3[589]: Modem found!
Oct 27 16:46:08 Prostotnic1 pppoa3[589]: host --> pppoa3 --> modem stream
ready
Oct 27 16:46:08 Prostotnic1 pppoa3[589]: modem --> pppoa3 --> host stream
ready
and ifconfig tap0:
tap0: flags=8802<BROADCAST,SIMPLEX,MULTICAST> mtu 1500
ether 00:bd:19:38:01:00
Opened by PID 588
and ppp.log:
ppp[604]: Phase: Using interface: tun0
ppp[604]: Phase: deflink: Created in closed state
ppp[604]: tun0: Command: bostream: set authname [EMAIL PROTECTED]
ppp[604]: tun0: Command: bostream: set authkey ********
ppp[604]: tun0: Command: bostream: set device PPPoE:tap0
ppp[604]: tun0: Command: bostream: set speed sync
ppp[604]: tun0: Command: bostream: set timeout 1
ppp[604]: tun0: Command: bostream: set redial 15 10000
ppp[604]: tun0: Command: bostream: set dial
ppp[604]: tun0: Command: bostream: set login
ppp[604]: tun0: Command: bostream: set ifaddr 10.0.0.1/0 10.0.0.2/0
255.255.255.0 0.0.0.0
ppp[604]: tun0: Command: bostream: add default HISADDR
ppp[604]: tun0: Warning: Add route failed: 0.0.0.0/0 already exists
ppp[604]: tun0: Command: bostream: enable dns
ppp[605]: tun0: Phase: PPP Started (ddial mode).
ppp[605]: tun0: Phase: bundle: Establish
ppp[605]: tun0: Phase: deflink: closed -> opening
ppp[605]: tun0: Phase: deflink: Connected!
ppp[605]: tun0: Phase: deflink: opening -> dial
ppp[605]: tun0: Phase: deflink: dial -> carrier
ppp[605]: tun0: Phase: deflink: Disconnected!
ppp[605]: tun0: Phase: deflink: carrier -> hangup
ppp[605]: tun0: Phase: deflink: Connect time: 5 secs: 0 octets in, 0 octets
out
ppp[605]: tun0: Phase: deflink: 0 packets in, 0 packets out
ppp[605]: tun0: Phase: total 0 bytes/sec, peak 0 bytes/sec on Mon Oct 27
16:48:57 2003
ppp[605]: tun0: Phase: deflink: hangup -> opening
ppp[605]: tun0: Phase: deflink: Enter pause (15) for
Liste de diffusion modem ALCATEL SpeedTouch USB
Pour se d�sinscrire : mailto:[EMAIL PROTECTED]
