Hello Rainer, It's a pleasure help somebody i told you. I'm still have a NOT working speedtouch 330 Rev 4 in my openSuse 10.2 64bits edition :( where the nas0 device does not exists
Antares --- Rainer Dorsch <[EMAIL PROTECTED]> escribió: > > Hi Antares, > > thanks for your quick reply. I just found that I > interchanged VPI and VCI. > After fixing that, the speedtouch 330 attached to > the nslu2 works very well: > > LKG7F63BB:~# pppd call lycos-dsl > Plugin rp-pppoe.so loaded. > PADS: Service-Name: '' > PPP session is 21160 > using channel 2 > Using interface ppp0 > Connect: ppp0 <--> nas0 > sent [LCP ConfReq id=0x1 <mru 1492> <magic > 0x3659501d>] > rcvd [LCP ConfReq id=0x1 <mru 1492> <auth pap> > <magic 0xd345b397>] > sent [LCP ConfAck id=0x1 <mru 1492> <auth pap> > <magic 0xd345b397>] > rcvd [LCP ConfAck id=0x1 <mru 1492> <magic > 0x3659501d>] > sent [LCP EchoReq id=0x0 magic=0x3659501d] > sent [PAP AuthReq id=0x1 > user="flatrate/[EMAIL PROTECTED]" > password=<hidden>] > rcvd [LCP EchoRep id=0x0 magic=0xd345b397 00 07 1c > a1] > rcvd [LCP ConfReq id=0x7 <mru 1492> <auth pap> > <magic 0xd345b397>] > sent [LCP ConfReq id=0x2 <mru 1492> <magic > 0xaab34681>] > sent [LCP ConfAck id=0x7 <mru 1492> <auth pap> > <magic 0xd345b397>] > rcvd [LCP ConfAck id=0x2 <mru 1492> <magic > 0xaab34681>] > sent [LCP EchoReq id=0x0 magic=0xaab34681] > sent [PAP AuthReq id=0x2 > user="flatrate/[EMAIL PROTECTED]" > password=<hidden>] > rcvd [PAP AuthAck id=0x2 ""] > PAP authentication succeeded > peer from calling number 00:13:7F:29:93:19 > authorized > sent [IPCP ConfReq id=0x1 <addr 0.0.0.0> <ms-dns1 > 0.0.0.0> <ms-dns3 0.0.0.0>] > rcvd [IPCP ConfReq id=0xd3 <addr 213.20.223.24>] > sent [IPCP ConfAck id=0xd3 <addr 213.20.223.24>] > rcvd [IPCP ConfNak id=0x1 <addr 217.190.180.37> > <ms-dns1 62.53.220.69> > <ms-dns3 193.189.244.205>] > sent [IPCP ConfReq id=0x2 <addr 217.190.180.37> > <ms-dns1 62.53.220.69> > <ms-dns3 193.189.244.205>] > rcvd [IPCP ConfAck id=0x2 <addr 217.190.180.37> > <ms-dns1 62.53.220.69> > <ms-dns3 193.189.244.205>] > not replacing existing default route via 192.168.1.1 > Cannot determine ethernet address for proxy ARP > local IP address 217.190.180.37 > remote IP address 213.20.223.24 > primary DNS address 62.53.220.69 > secondary DNS address 193.189.244.205 > LKG7F63BB:~# ping 213.20.223.24 > PING 213.20.223.24 (213.20.223.24) 56(84) bytes of > data. > 64 bytes from 213.20.223.24: icmp_seq=1 ttl=255 > time=58.9 ms > 64 bytes from 213.20.223.24: icmp_seq=2 ttl=255 > time=56.6 ms > > Thanks again for all your help, > Rainer > > Am Freitag, 24. November 2006 00:10 schrieb antares > dark: > > Hi, Rainer. > > > > First of all your modem is loading the firmware? > when > > boot the machine, the right led should blink 8 or > 9 > > times. > > > > Second, are you sure that Deutsche Telekom is > using > > PPPoE? > > > > Third have you set your user & pass in > > /etc/ppp/chap-secrets > > /etc/ppp/pap-secrets > > > > in this form: > > "[EMAIL PROTECTED]" "*" "password" > > or... > > '[EMAIL PROTECTED]' '*' 'password' > > > > only one is needed depending if its PPPoA or PPPoE > > > > Take a look at this page and read it carefully. > > > > http://www.linux-usb.org/SpeedTouch/LFS/index.html > > > > It's a pleasure help somebody, and more if you're > too > > far from my country. > > > > Antares > > > > --- Rainer Dorsch <[EMAIL PROTECTED]> escribió: > > > Hi Antares, > > > > > > thank you for your quick reply. It brought me a > step > > > further and it was easy > > > enough to find out the 1.32 for the Deutsche > Telekom > > > (with a little help of > > > Google). > > > > > > Now I am stuck with > > > > > > Timeout waiting for PADO packets > > > > > > Google showed several hits on this error, but I > > > found no conclusion. > > > > > > Any help would be appreciated. > > > > > > This is what I did: > > > > > > LKG7F63BB:~# modprobe speedtch > > > LKG7F63BB:~# modprobe br2684 > > > LKG7F63BB:~# modprobe pppoe > > > LKG7F63BB:~# dmesg | grep 'ADSL line is up' > > > ATM dev 0: ADSL line is up (864 kb/s down | 160 > kb/s > > > up) > > > LKG7F63BB:~# br2684ctl -b -c 0 -a 32.1 > > > br2684ctl[3762]: Interface "nas0" created > > > sucessfully > > > br2684ctl[3762]: Communicating over ATM 0.32.1, > > > encapsulation: LLC > > > br2684ctl[3762]: Interface configured > > > LKG7F63BB:~# ip link set nas0 up > > > LKG7F63BB:~# pppd call lycos-dsl > > > Plugin rp-pppoe.so loaded. > > > Timeout waiting for PADO packets > > > Unable to complete PPPoE Discovery > > > LKG7F63BB:~# > > > > > > > > > The pppd config (I replaced [EMAIL PROTECTED] with my > data): > > > > > > LKG7F63BB:~# cat /etc/ppp/peers/lycos-dsl > > > noipdefault > > > defaultroute > > > user "[EMAIL PROTECTED]" > > > noauth > > > updetach > > > usepeerdns > > > plugin rp-pppoe.so > > > nas0 > > > > > > ### If the firmware loads and pppd won't > > > ### connect uncomment this option to make > > > ### pppd be more verbose in the system log > > > > > > debug > > > > > > ### For more details (and more options) > > > ### read man pppd > > > LKG7F63BB:~# > > > > > > Thanks, > > > Rainer > > > > > > PS: My speedtouch shows firmware verison 0.01. > > > Should I be worried? > > > LKG7F63BB:~# awk '/4061/ { print $5 }' > > > /proc/bus/usb/devices > > > 0.01 > > > LKG7F63BB:~# > > > > > > > > > Am Mittwoch, 22. November 2006 14:47 schrieb > antares > > > > > > dark: > > > > Hello, look at the 6th line: > > > > > LKG7F63BB:~# br2684ctl -b -c 0 -a VP.VC > > > > > > > > You shoud change the VP.VC by numbers like the > > > > > > ones in > > > > > > > in this listing (i don't see telekom germany) > > > > > http://www.linux-usb.org/SpeedTouch/faq/index.html#q12 > === message truncated === __________________________________________________ Correo Yahoo! Espacio para todos tus mensajes, antivirus y antispam ¡gratis! ¡Abrí tu cuenta ya! - http://correo.yahoo.com.ar Liste de diffusion modem ALCATEL SpeedTouch USB Pour se désinscrire : mailto:[EMAIL PROTECTED]
