----- Original Message ----- From: "Samuel Adams" <[EMAIL PROTECTED]> To: <speedtouch@ml.free.fr> Sent: Monday, January 29, 2007 8:13 PM Subject: [speedtouch] Re: Alcatel Speedtouch USB ADSL using PPPoA - firmware loads and then authentication
... > Jan 29 11:59:29 localhost kernel: [4294676.035000] uhci_hcd 0000:00:1f.2: new USB bus registered, assigned bus number 1 > Jan 29 11:59:29 localhost kernel: [4294676.035000] uhci_hcd 0000:00:1f.2: irq 11, io base 0x0000ff80 > Jan 29 11:59:29 localhost kernel: [4294676.036000] hub 1-0:1.0: USB hub found > Jan 29 11:59:29 localhost kernel: [4294676.036000] hub 1-0:1.0: 2 ports detected > Jan 29 11:59:29 localhost kernel: [4294676.304000] Attempting manual resume > Jan 29 11:59:29 localhost kernel: [4294676.343000] usb 1-1: new full speed USB device using uhci_hcd and address 2 > Jan 29 11:59:29 localhost kernel: [4294676.363000] EXT3-fs: mounted filesystem with ordered data mode. > Jan 29 11:59:29 localhost kernel: [4294676.397000] kjournald starting. Commit interval 5 seconds > Jan 29 11:59:29 localhost kernel: [4294676.466000] hub 1-1:1.0: USB hub found > Jan 29 11:59:29 localhost kernel: [4294676.468000] hub 1-1:1.0: 4 ports detected > Jan 29 11:59:29 localhost kernel: [4294676.781000] usb 1-2: new full speed USB device using uhci_hcd and address 3 > Jan 29 11:59:29 localhost kernel: [4294677.083000] usb 1-1.2: new full speed USB device using uhci_hcd and address 4 > Jan 29 11:59:29 localhost kernel: [4294677.346000] usb 1-1.3: new full speed USB device using uhci_hcd and address 5 > Jan 29 11:59:29 localhost kernel: [4294677.435000] usb 1-1.3: 400mA over 100mA budget! > Jan 29 11:59:29 localhost kernel: [4294677.436000] hub 1-1:1.0: 194mA over power budget! > Jan 29 11:59:29 localhost kernel: [4294677.605000] usb 1-1.4: new full speed USB device using uhci_hcd and address 6 > Jan 29 11:59:29 localhost kernel: [4294677.724000] usb 1-1.3: 400mA over 100mA budget! > Jan 29 11:59:29 localhost kernel: [4294677.724000] hub 1-1:1.0: 196mA over power budget! This is not good but it should not be related to speedtouch problem as speedtouch is on 1-2 hub (see bellow) You should consider to add a powered usb hub to feed usb devices as needed or plug them differently ... > Jan 29 11:59:29 localhost kernel: [4294695.534000] usb 1-2: reset full speed USB device using uhci_hcd and address 3 > Jan 29 11:59:29 localhost kernel: [4294695.659000] usbcore: registered new driver speedtch > Jan 29 11:59:29 localhost kernel: [4294695.709000] speedtch 1-2:1.0: found stage 1 firmware speedtch-1.bin > Jan 29 11:59:29 localhost kernel: [4294695.775000] drivers/usb/class/usblp.c: usblp0: USB Bidirectional printer dev 6 if 0 alt 1 proto 2 vid 0x03F0 pid 0x1004 > Jan 29 11:59:29 localhost kernel: [4294695.776000] usbcore: registered new driver usblp > Jan 29 11:59:29 localhost kernel: [4294695.776000] drivers/usb/class/usblp.c: v0.13: USB Printer Device Class driver ... > Jan 29 11:59:29 localhost kernel: [4294695.814000] Initializing USB Mass Storage driver... > Jan 29 11:59:29 localhost kernel: [4294695.814000] scsi0 : SCSI emulation for USB Mass Storage devices > Jan 29 11:59:29 localhost kernel: [4294695.815000] usb-storage: device found at 4 > Jan 29 11:59:29 localhost kernel: [4294695.815000] usb-storage: waiting for device to settle before scanning > Jan 29 11:59:29 localhost kernel: [4294695.815000] usbcore: registered new driver usb-storage > Jan 29 11:59:29 localhost kernel: [4294695.815000] USB Mass Storage support registered. > Jan 29 11:59:29 localhost kernel: [4294695.838000] quickcam: QuickCam USB camera found (driver version QuickCam USB 0.6.3 $Date: 2005/04/15 19:32:49 $) > Jan 29 11:59:29 localhost kernel: [4294695.838000] quickcam: Kernel:2.6.15-23-386 bus:1 class:FF subclass:FF vendor:046D product:0840 > Jan 29 11:59:29 localhost kernel: [4294695.842000] quickcam: Sensor HDCS-1000/1100 detected > Jan 29 11:59:29 localhost kernel: [4294695.844000] quickcam: Registered device: /dev/video0 > Jan 29 11:59:29 localhost kernel: [4294695.844000] usbcore: registered new driver quickcam > Jan 29 11:59:29 localhost kernel: [4294696.124000] speedtch 1-2:1.0: found stage 2 firmware speedtch-2.bin speedtouch look correctly initialised at this point, you should be able see speedtouch modem doing cat /proc/net/atm/devices This look a configuration attempting to start a classical modem, this should not happen with adsl modem > Jan 29 12:00:26 localhost chat[3802]: alarm > Jan 29 12:00:26 localhost chat[3802]: send (AT^M) > Jan 29 12:00:26 localhost chat[3802]: expect (OK) > Jan 29 12:01:26 localhost chat[3802]: alarm > Jan 29 12:01:26 localhost chat[3802]: Failed > Jan 29 12:01:26 localhost pppd[3681]: Connect script failed Gilles Liste de diffusion modem ALCATEL SpeedTouch USB Pour se désinscrire : mailto:[EMAIL PROTECTED]
