Hilti drop in, bolt and eye piece or sidewinder (sammy screw)
On Sun, Jul 4, 2010 at 8:02 PM, Basalay, Andrea <[email protected]>wrote: > Pilot hole is 1/4" with CST Sammys vs larger diam required with a drop in. > Andi > > -----Original Message----- > From: Bob Knight <[email protected]> > Sent: Sunday, July 04, 2010 3:04 PM > To: [email protected] <[email protected]> > Subject: RE: Pre-Cast Concrete Plank Hanger > > Todd, > What sammy? The concrete screw? I looked at that and as long as you hit > the in-between points it looks ok. I think you could do the same with > inserts, so until something better comes up that's what I'm going with. > > Happy 4th! > > Bob > > -----Original Message----- > From: [email protected] > [mailto:[email protected]] On Behalf Of Todd > Williams > Sent: Sunday, July 04, 2010 4:59 AM > To: [email protected] > Subject: Re: Pre-Cast Concrete Plank Hanger > > There is a Sammy for vertical installation in concrete and their detail > shows it going into plank. Would that work? > > > > At 08:29 PM 7/3/2010, you wrote: > >Hilti has a "shorty" that is usually acceptedn(about 1/4"), other than > that > >then I guess you have to go with (this has conc tee's?) a sidewinder by > >"sammy screws" other than that, basically I've had to do a hanger > >(dimensioned) layout and have them installed on the plywood before the > pour > >and heaven help ya if you forget one. On an off note superglue is being > >evaluated by FM. > > > >On Sat, Jul 3, 2010 at 6:21 PM, Bob Knight <[email protected]> wrote: > > > > > I'm looking at a project that has pre-cast concrete plank floor and > roof > > > decks. The spec has specifically disallowed the use of HDI-P inserts. > > > What > > > other options are available? I've been searching but haven't come up > with > > > anything else. > > > > > > Thanks, > > > > > > Bob Knight > > > > > > _______________________________________________ > > > Sprinklerforum mailing list > > > [email protected] > > > http://fireball.firesprinkler.org/mailman/listinfo/sprinklerforum > > > > > > For Technical Assistance, send an email to: [email protected] > > > > > > To Unsubscribe, send an email > > > to:[email protected]<to%[email protected]> > <to%3asprinklerforum-requ...@fire > sprinkler.org> > > > (Put the word unsubscribe in the subject field) > > > > > > > > > > >-- > >Tom Poisal, CET > >_______________________________________________ > >Sprinklerforum mailing list > >[email protected] > >http://fireball.firesprinkler.org/mailman/listinfo/sprinklerforum > > > >For Technical Assistance, send an email to: [email protected] > > > >To Unsubscribe, send an email > >to:[email protected]<to%[email protected]> > >(Put the word unsubscribe in the subject field) > > Todd G. Williams, PE > Fire Protection Design/Consulting > Stonington, CT > 860.535.2080 > www.fpdc.com > > _______________________________________________ > Sprinklerforum mailing list > [email protected] > http://fireball.firesprinkler.org/mailman/listinfo/sprinklerforum > > For Technical Assistance, send an email to: [email protected] > > To Unsubscribe, send an email > to:[email protected]<to%[email protected]> > (Put the word unsubscribe in the subject field) > > > > _______________________________________________ > Sprinklerforum mailing list > [email protected] > http://fireball.firesprinkler.org/mailman/listinfo/sprinklerforum > > For Technical Assistance, send an email to: [email protected] > > To Unsubscribe, send an email > to:[email protected]<to%[email protected]> > (Put the word unsubscribe in the subject field) > _______________________________________________ > Sprinklerforum mailing list > [email protected] > http://fireball.firesprinkler.org/mailman/listinfo/sprinklerforum > > For Technical Assistance, send an email to: [email protected] > > To Unsubscribe, send an email > to:[email protected]<to%[email protected]> > (Put the word unsubscribe in the subject field) > -- Tom Poisal, CET _______________________________________________ Sprinklerforum mailing list [email protected] http://fireball.firesprinkler.org/mailman/listinfo/sprinklerforum For Technical Assistance, send an email to: [email protected] To Unsubscribe, send an email to:[email protected] (Put the word unsubscribe in the subject field)
