This implements the reading and writing of the configuration varables from the Suunto Vyper family devices.
Everything here is implemented based on the excellent information on: http://www.sarnau.info/papers:suunto_vyper Signed-off-by: Anton Lundin <[email protected]> --- configuredivecomputerthreads.cpp | 167 ++++++++++++++++++++++++++++++++++++++- 1 file changed, 165 insertions(+), 2 deletions(-) diff --git a/configuredivecomputerthreads.cpp b/configuredivecomputerthreads.cpp index 7554467..6f0ff9a 100644 --- a/configuredivecomputerthreads.cpp +++ b/configuredivecomputerthreads.cpp @@ -44,6 +44,25 @@ #define OSTC3_PRESSURE_SENSOR_OFFSET 0x35 #define OSTC3_SAFETY_STOP 0x36 +#define SUUNTO_VYPER_MAXDEPTH 0x1e +#define SUUNTO_VYPER_TOTAL_TIME 0x20 +#define SUUNTO_VYPER_NUMBEROFDIVES 0x22 +#define SUUNTO_VYPER_COMPUTER_TYPE 0x24 +#define SUUNTO_VYPER_FIRMWARE 0x25 +#define SUUNTO_VYPER_SERIALNUMBER 0x26 +#define SUUNTO_VYPER_CUSTOM_TEXT 0x2c +#define SUUNTO_VYPER_SAMPLING_RATE 0x53 +#define SUUNTO_VYPER_ALTITUDE_SAFETY 0x54 +#define SUUNTO_VYPER_TIMEFORMAT 0x60 +#define SUUNTO_VYPER_UNITS 0x62 +#define SUUNTO_VYPER_MODEL 0x63 +#define SUUNTO_VYPER_LIGHT 0x64 +#define SUUNTO_VYPER_ALARM_DEPTH_TIME 0x65 +#define SUUNTO_VYPER_ALARM_TIME 0x66 +#define SUUNTO_VYPER_ALARM_DEPTH 0x68 +#define SUUNTO_VYPER_CUSTOM_TEXT_LENGHT 30 + + ReadSettingsThread::ReadSettingsThread(QObject *parent, device_data_t *data) : QThread(parent), m_data(data) { @@ -57,8 +76,112 @@ void ReadSettingsThread::run() rc = dc_device_open(&m_data->device, m_data->context, m_data->descriptor, m_data->devname); if (rc == DC_STATUS_SUCCESS) { DeviceDetails *m_deviceDetails = new DeviceDetails(0); + switch (dc_device_get_type(m_data->device)) { + case DC_FAMILY_SUUNTO_VYPER: + supported = true; + unsigned char data[SUUNTO_VYPER_CUSTOM_TEXT_LENGHT + 1]; + rc = dc_device_read(m_data->device, SUUNTO_VYPER_MAXDEPTH, data, 2); + if (rc == DC_STATUS_SUCCESS) { + // in ft * 128.0 + int depth = feet_to_mm(data[0] << 8 ^ data[1]) / 128; + m_deviceDetails->setMaxDepth(depth); + } + rc = dc_device_read(m_data->device, SUUNTO_VYPER_TOTAL_TIME, data, 2); + if (rc == DC_STATUS_SUCCESS) { + int total_time = data[0] << 8 ^ data[1]; + m_deviceDetails->setTotalTime(total_time); + } + rc = dc_device_read(m_data->device, SUUNTO_VYPER_NUMBEROFDIVES, data, 2); + if (rc == DC_STATUS_SUCCESS) { + int number_of_dives = data[0] << 8 ^ data[1]; + m_deviceDetails->setNumberOfDives(number_of_dives); + } + rc = dc_device_read(m_data->device, SUUNTO_VYPER_COMPUTER_TYPE, data, 1); + if (rc == DC_STATUS_SUCCESS) { + const char *model; + switch(data[0]) { + case 0x03: + model = "Stinger"; + break; + case 0x04: + model = "Mosquito"; + break; + case 0x0A: + model = "new Vyper"; + break; + case 0x0C: + model = "Vyper or Cobra"; + break; + case 0x0B: + model = "Vytec"; + break; + case 0x0D: + model = "Gekko"; + break; + default: + model = "UNKNOWN"; + } + m_deviceDetails->setModel(model); + } + rc = dc_device_read(m_data->device, SUUNTO_VYPER_FIRMWARE, data, 1); + if (rc == DC_STATUS_SUCCESS) { + m_deviceDetails->setFirmwareVersion(QString::number(data[0]) + ".0.0"); + } + rc = dc_device_read(m_data->device, SUUNTO_VYPER_SERIALNUMBER, data, 4); + if (rc == DC_STATUS_SUCCESS) { + int serial_number = data[0] * 1000000 + data[1] * 10000 + data[2] * 100 + data[3]; + m_deviceDetails->setSerialNo(QString::number(serial_number)); + } + rc = dc_device_read(m_data->device, SUUNTO_VYPER_CUSTOM_TEXT, data, SUUNTO_VYPER_CUSTOM_TEXT_LENGHT); + if (rc == DC_STATUS_SUCCESS) { + data[SUUNTO_VYPER_CUSTOM_TEXT_LENGHT] = 0; + m_deviceDetails->setCustomText((const char*) data); + } + rc = dc_device_read(m_data->device, SUUNTO_VYPER_SAMPLING_RATE, data, 1); + if (rc == DC_STATUS_SUCCESS) { + m_deviceDetails->setSamplingRate((int) data[0]); + } + rc = dc_device_read(m_data->device, SUUNTO_VYPER_ALTITUDE_SAFETY, data, 1); + if (rc == DC_STATUS_SUCCESS) { + m_deviceDetails->setAltitude(data[0] & 0x03); + m_deviceDetails->setPersonalSafety(data[0] >> 2 & 0x03); + } + rc = dc_device_read(m_data->device, SUUNTO_VYPER_TIMEFORMAT, data, 1); + if (rc == DC_STATUS_SUCCESS) { + m_deviceDetails->setTimeFormat(data[0] & 0x01); + } + rc = dc_device_read(m_data->device, SUUNTO_VYPER_UNITS, data, 1); + if (rc == DC_STATUS_SUCCESS) { + m_deviceDetails->setUnits(data[0] & 0x01); + } + rc = dc_device_read(m_data->device, SUUNTO_VYPER_MODEL, data, 1); + if (rc == DC_STATUS_SUCCESS) { + m_deviceDetails->setDiveMode(data[0] & 0x03); + } + rc = dc_device_read(m_data->device, SUUNTO_VYPER_LIGHT, data, 1); + if (rc == DC_STATUS_SUCCESS) { + m_deviceDetails->setLightEnabled(data[0] >> 7); + m_deviceDetails->setLight(data[0] & 0x7F); + } + rc = dc_device_read(m_data->device, SUUNTO_VYPER_ALARM_DEPTH_TIME, data, 1); + if (rc == DC_STATUS_SUCCESS) { + m_deviceDetails->setAlarmTimeEnabled(data[0] & 0x01); + m_deviceDetails->setAlarmDepthEnabled(data[0] >> 1 & 0x01); + } + rc = dc_device_read(m_data->device, SUUNTO_VYPER_ALARM_TIME, data, 2); + if (rc == DC_STATUS_SUCCESS) { + m_deviceDetails->setAlarmTime(data[0] << 8 ^ data[1]); + } + rc = dc_device_read(m_data->device, SUUNTO_VYPER_ALARM_DEPTH, data, 2); + if (rc == DC_STATUS_SUCCESS) { + int depth = feet_to_mm(data[0] << 8 ^ data[1]) / 128; + m_deviceDetails->setAlarmDepth(depth); + } + emit devicedetails(m_deviceDetails); + break; #if DC_VERSION_CHECK(0, 5, 0) - if (dc_device_get_type(m_data->device) == DC_FAMILY_HW_OSTC3) { + case DC_FAMILY_HW_OSTC3: + { supported = true; m_deviceDetails->setBrightness(0); m_deviceDetails->setCustomText(""); @@ -300,7 +423,12 @@ void ReadSettingsThread::run() emit devicedetails(m_deviceDetails); } + break; #endif // divecomputer 0.5.0 + default: + supported = false; + break; + } dc_device_close(m_data->device); if (!supported) { @@ -330,8 +458,39 @@ void WriteSettingsThread::run() dc_status_t rc; rc = dc_device_open(&m_data->device, m_data->context, m_data->descriptor, m_data->devname); if (rc == DC_STATUS_SUCCESS) { + switch (dc_device_get_type(m_data->device)) { + case DC_FAMILY_SUUNTO_VYPER: + supported = true; + unsigned char data; + unsigned char data2[2]; + dc_device_write(m_data->device, SUUNTO_VYPER_CUSTOM_TEXT, + // Convert the customText to a 30 char wide padded with " " + (const unsigned char *) QString("%1").arg(m_deviceDetails->customText(), -30, QChar(' ')).toUtf8().data(), + SUUNTO_VYPER_CUSTOM_TEXT_LENGHT); + data = m_deviceDetails->samplingRate(); + dc_device_write(m_data->device, SUUNTO_VYPER_SAMPLING_RATE, &data, 1); + data = m_deviceDetails->personalSafety() << 2 ^ m_deviceDetails->altitude(); + dc_device_write(m_data->device, SUUNTO_VYPER_ALTITUDE_SAFETY, &data, 1); + data = m_deviceDetails->timeFormat(); + dc_device_write(m_data->device, SUUNTO_VYPER_TIMEFORMAT, &data, 1); + data = m_deviceDetails->units(); + dc_device_write(m_data->device, SUUNTO_VYPER_UNITS, &data, 1); + data = m_deviceDetails->diveMode(); + dc_device_write(m_data->device, SUUNTO_VYPER_MODEL, &data, 1); + data = m_deviceDetails->lightEnabled() << 7 ^ (m_deviceDetails->light() & 0x7F); + dc_device_write(m_data->device, SUUNTO_VYPER_LIGHT, &data, 1); + data = m_deviceDetails->alarmDepthEnabled() << 1 ^ m_deviceDetails->alarmTimeEnabled(); + dc_device_write(m_data->device, SUUNTO_VYPER_ALARM_DEPTH_TIME, &data, 1); + data2[0] = m_deviceDetails->alarmTime() >> 8; + data2[1] = m_deviceDetails->alarmTime() & 0xFF; + dc_device_write(m_data->device, SUUNTO_VYPER_ALARM_TIME, data2, 2); + data2[0] = (int)(mm_to_feet(m_deviceDetails->alarmDepth()) * 128) >> 8; + data2[1] = (int)(mm_to_feet(m_deviceDetails->alarmDepth()) * 128) & 0x0FF; + dc_device_write(m_data->device, SUUNTO_VYPER_ALARM_DEPTH, data2, 2); + break; #if DC_VERSION_CHECK(0,5,0) - if (dc_device_get_type(m_data->device) == DC_FAMILY_HW_OSTC3) { + case DC_FAMILY_HW_OSTC3: + { supported = true; //write gas values unsigned char gas1Data[4] = {m_deviceDetails->gas1().oxygen, @@ -496,6 +655,10 @@ void WriteSettingsThread::run() } } #endif // divecomputer 0.5.0 + default: + supported = false; + break; + } dc_device_close(m_data->device); if (!supported) { -- 1.9.1 _______________________________________________ subsurface mailing list [email protected] http://lists.subsurface-divelog.org/cgi-bin/mailman/listinfo/subsurface
