Here you go:
lo0: flags=2001000849<UP,LOOPBACK,RUNNING,MULTICAST,IPv4,VIRTUAL> mtu
8232 index 1
inet 127.0.0.1 netmask ff000000
bge0: flags=1000843<UP,BROADCAST,RUNNING,MULTICAST,IPv4> mtu 1500 index 2
inet 172.16.5.241 netmask ffffff00 broadcast 172.16.5.255
ether 0:9:3d:12:a5:1f
bge1: flags=1000843<UP,BROADCAST,RUNNING,MULTICAST,IPv4> mtu 1500 index 3
inet 172.16.25.241 netmask ffffff00 broadcast 172.16.25.255
ether 0:9:3d:12:a5:20
Brad Lackey wrote:
Can you also send your ifconfig -a output?
Brad Lackey wrote:
Is there anything besides DTU's on the bge1 networ? why not use
"utadm -a bge1"?
Brad
LOEWENTHAL Simon wrote:
Dear All,
Here's a New Year's problem ;)
I have just set-up a SunFire z20 as a SunRay server. It has two
interfaces bge0 & bge1. The DTUs are bge1 & have no need to route
out over bge0. System is:
SunOS sbfsr2 5.10 Generic_118844-20 i86pc i386 i86pc
I ran utadm but get this error message:
Error: unable to get information on primary interface
Has anyone seen this afore?
Many thanks, S.
Here are all the errors:
utadm -A 172.16.25.0
### Configuring /etc/nsswitch.conf
### Configuring Service information for Sun Ray
### Disabling Routing
Selected values for subnetwork "172.16.25.0"
net mask: 255.255.255.0
no IP addresses offered
auth server list: 172.16.5.241
firmware server: 172.16.5.241
Accept as is? ([Y]/N): n
netmask: 255.255.255.0 (cannot be changed - system defined netmask)
Do you want to offer IP addresses for this subnet? (Y/[N]): Y
new first Sun Ray address: [172.16.25.4] 172.16.25.10
number of Sun Ray addresses to allocate: [245] 100
auth server list: 172.16.5.241
To read auth server list from file, enter file name:
Auth server IP address (enter <CR> to end list): 172.16.5.241
Auth server IP address (enter <CR> to end list): 172.16.25.241
Auth server IP address (enter <CR> to end list):
If no server in the auth server list responds,
should an auth server be located by broadcasting on the network?
([Y]/N):
new firmware server: [172.16.5.241] 172.16.25.241
new router: [172.16.25.1]
Selected values for subnetwork "172.16.25.0"
net mask: 255.255.255.0
first unit address: 172.16.25.10
last unit address: 172.16.25.109
auth server list: 172.16.5.241 172.16.25.241
firmware server: 172.16.25.241
router: 172.16.25.1
Accept as is? ([Y]/N):
Error: unable to get information on primary interface
Error: unable to get information on the primary interface.
### Configuring firmware version for Sun Ray
Error: cannot set firmware version to network macro "172.16.25.0":
Configuration for DHCP subnet 172.16.25.0 does not exist.
### Configuring Sun Ray Logging Functions
### Turning on Sun Ray LAN connection
NOTE: utrestart must be run before LAN connections will be allowed
------------------------------------------------------------------------
_______________________________________________
SunRay-Users mailing list
[email protected]
http://www.filibeto.org/mailman/listinfo/sunray-users
--
*Brad Lackey*
Desktop and Mobility
Client Solutions Organization
(720) 548-3339
[EMAIL PROTECTED] <mailto:[EMAIL PROTECTED]>
------------------------------------------------------------------------
_______________________________________________
SunRay-Users mailing list
[email protected]
http://www.filibeto.org/mailman/listinfo/sunray-users
--
*Brad Lackey*
Desktop and Mobility
Client Solutions Organization
(720) 548-3339
[EMAIL PROTECTED] <mailto:[EMAIL PROTECTED]>
------------------------------------------------------------------------
_______________________________________________
SunRay-Users mailing list
[email protected]
http://www.filibeto.org/mailman/listinfo/sunray-users
_______________________________________________
SunRay-Users mailing list
[email protected]
http://www.filibeto.org/mailman/listinfo/sunray-users
