Hello,
I have change in the vda kiosk script file:
if [ $theUser != $SUN_SUNRAY_TOKEN ] ; then
$theUTTSCScript $theUTTSCArgs -r
comport:COM1=$DTDEVROOT/unit/dev/term/a -r disk:u=/tmp/SUNWut/mnt/$theUser -u
$theUser $theVM
else
$theUTTSCScript $theUTTSCArgs -r
comport:COM1=$DTDEVROOT/unit/dev/term/a -r disk:u=/tmp/SUNWut/mnt/$theUser
$theVM
fi
I try to connect with another console cable to an cisco router and it's work
fine. I can see the traffic between Sun-Ray and cisco device with hyperterminal
application for example.
Best regards,
Santiago Lorenzo
Department of Professional Services
[EMAIL PROTECTED]
www.uniway.es
Tel.: 91 579 96 10
Fax: 91 570 07 16
Building TECNUS
Bravo Murillo 178, 4th Floor
28020 Madrid, Spain
-----Original Message-----
From: [EMAIL PROTECTED] [mailto:[EMAIL PROTECTED] On Behalf Of P.S.M.Swamiji
Sent: lunes, 07 de enero de 2008 5:47
To: SunRay-Users mailing list
Subject: Re: [SunRay-Users] Olivetti PR2 banking printer with Sun-Ray
Santiago Lorenzo Puentes wrote:
>
>
> Hello,
>
>
> I've VDA Sun-Ray configuration and I've change SUNWvda kiosk script
> for comport mapped to the remote virtual Windows XP Professional system.
>
If you connect a printer to comport, then I think you need to configure
the printer first on
Sun Ray side and then pass that printer queue with uttsc using -r
printer option.
Thanks
P.S.M.Swamiji
Note:These are my personal opinions,nothing to do with my employer
>
> Does anyone have experience with this environment? I've tried to test
> it with the following configuration:
>
> - - - - - - - PR20 Configuration page - - - - - - - -
>
> Configuration mode
> -------------------------
> Emulation: Olivetti
> Emulation selection: Temporary
> Draft speed: Normal
> LQ Type: NLQ1
> Paper width: First Line
> Buzzer: Y
> Interface: RS232
> Baud rate: 9600
> Bit/Char: 8
> Parity: None
> Stop bit: 1
> DSR: Y
> DCD: Y
> Paper Edge detection: N
> Special forms: N
>
> Olivetti Menu
> -------------------------
> Emulation: PR40+
> Passbook: Y
> Binding: Horizontal
> Side: R
> Line buffer PR40 like: N
> Char generator: Olivetti
> Olivetti char set: E
> Char definition: Draft
> CPI: 10
> Vertical resolution: 1/240
> LF+CR: Y
> Reset with eject: Y
> Top margin PR40 like: Y
> Status request: no wait
>
> Option horizontal MSRW + MICR
> Standard: DIN/ISO
> Displacement: Standard
> Duplicate: Y
> Retry: 3
> Stripe handling: Normal
>
> PNS Selection: Y
> PNS #3416: N
> PNS #3517: Y
> 15 CPI: N
> PNS #4071: N
> PNS #4411: N
> PNS #5676: N
> PNS #5698: Y
> PNS #5775: Y
> PNS #8099: N
>
> - - - - - - - .:EOF:. Configuration page .:EOF:. - - - - - - - -
>
> But it hasn't work. I have tried to change bit/char, baud rate, parity
> and stop bit configuration but it hasn't work. The cable that connects
> printer and Sun-Ray is right and there is data flow through this cable.
>
> When I connect directly the printer to a customer workstation with the
> same cable and using the same application it works fine. (My customer
> can adjust communication parameters)
>
> I attach output of utseriald in debug mode. (Thanks Stoyan Angelov)
> http://www.sun-rays.org/tmp/slorenzo/utseriald-debug-9600-7e1.txt
> http://www.sun-rays.org/tmp/slorenzo/utseriald-debug-9600-8n1.txt
>
>
>
> Thank you very much.
>
> Best regards,
>
> Santiago Lorenzo
> Department of Professional Services
> [EMAIL PROTECTED]
>
>
> www.uniway.es
> Tel.: +034 91 579 96 10
> Fax : +034 91 570 07 16
> Building TECNUS
> Bravo Murillo 178, 4th Floor
> 28020 Madrid, Spain
>
> ------------------------------------------------------------------------
>
> _______________________________________________
> SunRay-Users mailing list
> [email protected]
> http://www.filibeto.org/mailman/listinfo/sunray-users
>
_______________________________________________
SunRay-Users mailing list
[email protected]
http://www.filibeto.org/mailman/listinfo/sunray-users
_______________________________________________
SunRay-Users mailing list
[email protected]
http://www.filibeto.org/mailman/listinfo/sunray-users
