Hi all, used also the new firmware after an upgrade of the production server to VDI 3.4.1 and run into similar issues and real show stoppers with 11.1.1.0_06_2013.03.01.22.48
- 26B against the old server (5.2.x) seems not to work anymore ... I'm ok with that, just important to know ... - power off is not honored anymore, none of the sunrays was shutting donw after 60 minutes I have configured in the .parms file ! - utresadm (e.g 1024x768) only works against SRS 5.4, but not any older ... e.g 5.3.1 - 11.1.1.0 burned down my production server with Xnewt spikes (the production server is still on VDI 3.4.1 aka SRS 5.3.1) with a load of 50 for 100 Users because of the Xnewt issues => don't use this combination I still have SR open which was Severity 1 the last two days ... I did an emergency update on one of my test servers to VDI 3.5 aka SRS 5.4 and run there currently with a load 14 now for 150 users !!! So I'm intending to force a downgrade to an earlier version of the FW, what would you recommend ? regards, thomas -----Ursprüngliche Nachricht----- Von: [email protected] [mailto:[email protected]] Im Auftrag von Craig Bender Gesendet: Donnerstag, 25. April 2013 17:45 An: [email protected] Betreff: Re: [SunRay-Users] Wrong Screen Size after firmware update to 11.1.1.0 What ustresadm command did you use to set it? Unlike utsettings, it's pretty sticky, but you have to do it correctly. If you just type utresadm, what output do you get? What's the make and model of the monitor? Can you also provide your utxconfig settings for your token? utxconfig -l (run from within your session) If possible, can you also provide xrandr -q output? (run from withing your session) On 4/25/13 8:30 AM, Christian Montero Hernández wrote: > > *From:* Jim Klimov <[email protected]> > *To:* [email protected] > *Sent:* Thursday, April 25, 2013 11:30 AM > *Subject:* Re: [SunRay-Users] Wrong Screen Size after firmware > update to 11.1.1.0 > > On 2013-04-25 15:05, Christian Montero Hernández wrote: > > Hello everyone, > > > > I was wondering if there is a default option for this firmware and > > screens, because I have an Oracle VDI 3.4.1 deployment and I was > using > > firmware 11.0.x, but after some time considering an update I > tried 1 Sun > > Ray 3 with the new firmware and then that Sun Ray 3 always shows a > > 1280x1024 resolution instead of the supported by the monitor > 1024x768, I > > have made a manual change to the screen size, but after a power cycle > > the resolution comes back to 1280x1024. > > > > - Has anyone had this issue before? > > - Why the change in behavior between firmware 11.0.x and 11.1.x? > > > > Thanks in advance for any tip you can give me. > > > You could try utresadm to enforce particular resolution for a particular > token (IEEE MAC address of the DTU). BTW, does this also happen if you > first power on the display, and then power on (or powercycle) the DTU, > that is, when the DTU should already know the display's best supported > resolution? Does it happen or change with different display models? > > HTH, > //Jim > > Hello Jim > > Thank for your reply to my message, I have tried utresadm, but it works > as long as I keep the session alive or the sun ray 3 is still powered on. > The display is always on, I never turn it off. (It just sleeps sometimes) > If I powercycle the sun ray 3 or if I, for some reason, unplug the power > cord the resolution is back to 1280x1024. > I have just tried this one Sun Ray 3, I have 5 other Sun Ray 3 but those > are in the warehouse. > I just did another test with a different screen, this time it was a 15" > wide, and the screen resolution was 1280x1024. > > This afternoon I will try another Sun Ray 3 with those 2 screens and let > you know if the behavior was the same or not. > > Thanks for the help. > > Best regards, > > Christian Montero H. > > > _______________________________________________ > SunRay-Users mailing list > [email protected] > http://www.filibeto.org/mailman/listinfo/sunray-users > _______________________________________________ SunRay-Users mailing list [email protected] http://www.filibeto.org/mailman/listinfo/sunray-users _________________ Diese Nachricht wurde vom OeNB Mailserver TLS verschluesselt empfangen _______________________________________________ SunRay-Users mailing list [email protected] http://www.filibeto.org/mailman/listinfo/sunray-users
