# fdisk -l Note: sector size is 4096 (not 512)
Disk /dev/hda: 120.0 GB, 120034123776 bytes 255 heads, 63 sectors/track, 1824 cylinders Units = cylinders of 16065 * 4096 = 65802240 bytes Disk /dev/hda doesn't contain a valid partition table # hdparm -l /dev/hda hdparm: invalid option -- l /dev/hda: # dmesg Linux version 2.6.19 (oleg@eyesisboxus) (gcc version 3.2.1 Axis release R64/1.64) #2 Sun Jan 15 18:43:42 MST 2012 Setting up paging and the MMU. On node 0 totalpages: 8192 DMA zone: 32 pages used for memmap DMA zone: 0 pages reserved DMA zone: 8160 pages, LIFO batch:0 Normal zone: 0 pages used for memmap Linux/CRISv32 port on ETRAX FS (C) 2003, 2004 Axis Communications AB Built 1 zonelists. Total pages: 8160 Kernel command line: root=/dev/mtdblock3 init=/linuxrc rootfstype=jffs2 PID hash table entries: 256 (order: 8, 1024 bytes) Dentry cache hash table entries: 8192 (order: 2, 32768 bytes) Inode-cache hash table entries: 4096 (order: 1, 16384 bytes) Memory: 40304k/65536k available (1744k kernel code, 25232k reserved, 622k data, 72k init) Calibrating delay loop... 199.47 BogoMIPS (lpj=997376) Mount-cache hash table entries: 1024 NET: Registered protocol family 16 SCSI subsystem initialized usbcore: registered new interface driver usbfs usbcore: registered new interface driver hub usbcore: registered new device driver usb NET: Registered protocol family 2 IP route cache hash table entries: 512 (order: -2, 2048 bytes) TCP established hash table entries: 2048 (order: 0, 8192 bytes) TCP bind hash table entries: 1024 (order: -1, 4096 bytes) TCP: Hash tables configured (established 2048 bind 1024) TCP reno registered Check hardware configuration of Elphel 353 camera Elphel 10349/10369 IO extension board is present fast_timer_init() JFFS2 version 2.2. (NAND) (C) 2001-2006 Red Hat, Inc. io scheduler noop registered (default) Serial: CRISv32 driver $Revision: 1.78 $ <6>ttyS0 at I/O 0xb0026000 (irq = 68) is a CRISv32 RAMDISK driver initialized: 16 RAM disks of 4096K size 1024 blocksize PPP generic driver version 2.4.2 ETRAX FS 10/100MBit ethernet v0.01 (c) 2003 Axis Communications AB eth0: changed MAC to 00:40:8C:CD:00:00 Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2 ide: Assuming 50MHz system bus speed for PIO modes; override with idebus=xx ide: ETRAX FS built-in ATA DMA controller cris_ide_init() Probing IDE interface ide0... hda: UOSHIBA MK1231GAM ! ! ! ! ! ! ! ! ! ! !, ATA DISK drive Physical sector 4096 bytes Updating sector size to match that of a hard drive: 4096 ide0 at 0x10000000-0x10000007,0x2c000000 on irq 65 hda: max request size: 128KiB hda: 234441648 sectors (120034 MB) w/128KiB Cache, CHS=16383/255/63, (U)DMA Skipping WIN_SPECIFY for large sectors drive, it is useless here and likely not supported Skipping WIN_SPECIFY for large sectors drive, it is useless here and likely not supported hda: cache flushes supported hda: hda1 Initializing USB Mass Storage driver... usbcore: registered new interface driver usb-storage USB Mass Storage support registered. usbcore: registered new interface driver usbserial drivers/usb/serial/usb-serial.c: USB Serial support registered for generic usbcore: registered new interface driver usbserial_generic drivers/usb/serial/usb-serial.c: USB Serial Driver core drivers/usb/serial/usb-serial.c: USB Serial support registered for Belkin / Peracom / GoHubs USB Serial Adapter usbcore: registered new interface driver belkin drivers/usb/serial/belkin_sa.c: USB Belkin Serial converter driver v1.2 drivers/usb/serial/usb-serial.c: USB Serial support registered for cp2101 usbcore: registered new interface driver cp2101 drivers/usb/serial/cp2101.c: Silicon Labs CP2101/CP2102 RS232 serial adaptor driver v0.07 drivers/usb/serial/usb-serial.c: USB Serial support registered for Garmin GPS usb/tty usbcore: registered new interface driver garmin_gps drivers/usb/serial/garmin_gps.c: garmin gps driver v0.28 drivers/usb/serial/usb-serial.c: USB Serial support registered for MCT U232 usbcore: registered new interface driver mct_u232 drivers/usb/serial/mct_u232.c: Magic Control Technology USB-RS232 converter driver z2.0 drivers/usb/serial/usb-serial.c: USB Serial support registered for pl2303 usbcore: registered new interface driver pl2303 drivers/usb/serial/pl2303.c: Prolific PL2303 USB to serial adaptor driver ETRAX FS stream co-processor driver v0.01, (c) 2003 Axis Communications AB stream co-processor: init done. axisflashmap: ... NAND device: Manufacturer ID: 0x20, Chip ID: 0xf1 (ST Micro NAND 128MiB 3,3V 8-bit) Additional Info: ID byte3=0x0, byte4=0x1d Bad block table found at page 65472, version 0x01 Bad block table found at page 65408, version 0x01 Flash is rated 30 ns, modifying bif_core_rw_grp3: old=0x6300483, new=0x6300001 NAND 128MiB 3,3V 8-bit: 0x08000000 bytes of NAND flash memory. axisflashmap: Set to boot from NAND flash, making NAND flash primary device. axisflashmap: flash read 512 bytes at 0x00040000, data: 00 b0 05 f0 25 ff ed 9c axisflashmap: partition table offset 10, data: ef be 84 00 12 0f 00 00 axisflashmap: Found a valid partition table at 0xc03019ae-0xc0301a3a. offset == 0x00040000, size == 0x007C0000 offset == 0x00800000, size == 0x01800000 offset == 0x02000000, size == 0x05000000 offset == 0x07000000, size == 0x00C00000 Creating 1 MTD partitions on "NAND 128MiB 3,3V 8-bit": 0x00000000-0x08000000 : "main" Creating 1 MTD partitions on "NAND 128MiB 3,3V 8-bit": 0x00000000-0x00040000 : "part0" Creating 1 MTD partitions on "NAND 128MiB 3,3V 8-bit": 0x00040000-0x00800000 : "part1" Creating 1 MTD partitions on "NAND 128MiB 3,3V 8-bit": 0x00800000-0x02000000 : "part2" Creating 1 MTD partitions on "NAND 128MiB 3,3V 8-bit": 0x02000000-0x07000000 : "part3" Creating 1 MTD partitions on "NAND 128MiB 3,3V 8-bit": 0x07000000-0x07c00000 : "part4" ETRAX FS GPIO driver v2.5, (c) 2003-2006 Axis Communications AB Elphel (R) model 353 FPGA (Xilinx (R) XC3S1200E) configuration driver - 132 Elphel (R) model 353 system clocks (PLL frequency synth.) driver - 133 fpga_control- 129 arch/cris/arch-v32/drivers/elphel/framepars.c:390:initGlobalPars GLOBALPARS(G_DEBUG)=0 arch/cris/arch-v32/drivers/elphel/framepars.c:420:initMultiPars GLOBALPARS(G_MULTI_NUM)=0 Elphel (R) Model 353 Frame Parameters device driver - 130 Elphel FPGA interrupts initialized Initializing DMA registers for EXTDMA3 - Elphel (R) Model 353 Camera Driver - 126 Elphel (R) model 353 i2c character device driver - 134, 2 channels Raw image access driver- 131 Elphel (R) Model 353 video buffer device driver- 135 Elphel (R) model 353 Exif device driver - 125 Starting Elphel (R) Model 353 Gamma Tables device driver - 137 Elphel (R) Model 353 Gamma Tables device driver - 137 Elphel (R) Model 353 Histograms device driver imu_logger- 141 TCP cubic registered NET: Registered protocol family 1 NET: Registered protocol family 17 VFS: Mounted root (jffs2 filesystem) readonly. Freeing unused kernel memory: 72k freed Empty flash at 0x00b7e238 ends at 0x00b7e800 Empty flash at 0x01b46038 ends at 0x01b46800 Empty flash at 0x01b5e544 ends at 0x01b5e800 Empty flash at 0x03369860 ends at 0x0336a000 eth0: changed MAC to 00:0E:64:08:19:B0 eth0: changed MAC to 00:0E:64:08:19:B0 arch/cris/arch-v32/drivers/elphel/framepars.c:390:initGlobalPars GLOBALPARS(G_DEBUG)=0 initSequencers:resetting both sequencers arch/cris/arch-v32/drivers/elphel/framepars.c:420:initMultiPars GLOBALPARS(G_MULTI_NUM)=0 sensor clock set to 20000000 removing MRST from the sensor Found MT9P001 2592x1944 sensor, chip ID=1801 trying MT9P001 Resetting MT9X001 sensor Reading sensor registers to the shadows: Initializing MT9X001 registers with default values: Starting hardware sequencers ETRAX FS IOP USB Host Controller version 1.10 (c) 2004, 2005, 2006 Axis Communications AB crisv32_hc crisv32_hc.0: ETRAX FS IOP USB Host Controller crisv32_hc crisv32_hc.0: new USB bus registered, assigned bus number 1 crisv32_hc crisv32_hc.0: irq 51, io base 0x00000000 usb usb1: configuration #1 chosen from 1 choice hub 1-0:1.0: USB hub found hub 1-0:1.0: 1 port detected crisv32_hc crisv32_hc.0: ETRAX FS IOP USB Host Controller usb 1-1: new full speed USB device using crisv32_hc and address 2 usb 1-1: configuration #1 chosen from 1 choice hub 1-1:1.0: USB hub found hub 1-1:1.0: 4 ports detected usbcore: registered new interface driver snd-usb-audio usbcore: registered new interface driver snd-usb-caiaq [root@Elphel353 /var]853# i rebooted the camera and repeat the process: [root@Elphel353 /var]853# mkfs.ext2 /dev/hda1 /mnt/0 mke2fs 1.38 (30-Jun-2005) Could not invalid blocks count - /mnt/0 > Could you recall what happened before camogm stopped recognizing the hdd ? > > Regards, > Oleg > > On 2 February 2012 16:36, Carlos Padial <[email protected]> wrote: >> >> ok, i follow the wiki again and post you what happens >> >> Command (m for help): p >> >> Disk /dev/hda: 120.0 GB, 120034123776 bytes >> 255 heads, 63 sectors/track, 1824 cylinders, total 29305206 sectors >> Units = sectors of 1 * 4096 = 4096 bytes >> >> Device Boot Start End 1K-Blocks Id System >> >> Command (m for help): n >> Command action >> e extended >> p primary partition (1-4) >> p >> Partition number (1-4): 1 >> First sector (1-29305205, default 1): Using default value 1 >> Last sector or +size or +sizeM or +sizeK (1-29305205, default >> 29305205): Using default value 29305205 >> >> Command (m for help): p >> >> Disk /dev/hda: 120.0 GB, 120034123776 bytes >> 255 heads, 63 sectors/track, 1824 cylinders, total 29305206 sectors >> Units = sectors of 1 * 4096 = 4096 bytes >> >> Device Boot Start End 1K-Blocks Id System >> /dev/hda1 1 29305205 117220820 83 Linux >> >> Command (m for help): w >> The partition table has been altered! >> >> Calling ioctl() to re-read partition table >> [root@Elphel353 /]1089# mkfs.ext2 /dev/hda1 -m0 -T largefile4 >> mke2fs 1.38 (30-Jun-2005) >> mkfs.ext2: Could not determine if /dev/hda1 is mounted >> >> Could not determine filesystem size >> >> ? >> >> and if i do cat /proc/partitions again hda1 isn't there >> >> _______________________________________________ >> Support-list mailing list >> [email protected] >> http://support.elphel.com/mailman/listinfo/support-list_support.elphel.com > > -- Carlos Padial surreal.asturnazari.es _______________________________________________ Support-list mailing list [email protected] http://support.elphel.com/mailman/listinfo/support-list_support.elphel.com
