== == == == == == Forwarded message == == == == == == 
>From : Richard Rigby<rri...@redzone.com>
To : <support-l...@elphel.com>
Date : Thu, 22 Feb 2018 18:28:08 -0800
Subject : 14Mpix sensor not detected
 == == == == == == Forwarded message == == == == == == 

Hello,

I have a 393 board as well as one 5 Mpix sensor and one 14 Mpix sensor. However 
only the 5Mpix sensor is working.


I am using the web interface to view the camera.


I have tried to run the init_elphel393.py script for both sensors and it looks 
to me that the 14 Mpix sensor cannot be detected.


This is the output from init_elphel393.py when only the 14 Mpix sensor is 
connected:
[  443.35] init_elphel393: Fan on
[  443.36] init_elphel393: Initialize USB hub
[  443.37] init_elphel393: 10389 was not detected: skipping USB hub init
[  443.37] init_elphel393: init_elphel393.py: ip = 192.168.0.9, mask = 
255.255.255.0
[  443.38] init_elphel393: init_elphel393.py: imgsrv
Set port number: 2323
Set port number: 2324
Set port number: 2325
Set port number: 2326
[  443.77] init_elphel393: init_elphel393.py: auto exposure daemon
autoexposure#0 started, daemon_bit=0x0, debug=0x1
autoexposure#1 started, daemon_bit=0x0, debug=0x1
autoexposure#2 started, daemon_bit=0x0, debug=0x1
autoexposure#3 started, daemon_bit=0x0, debug=0x1
[  443.99] autocampars: Processing camera state: INITIALIZED
[  444.05] autocampars: Active sensor ports:  master_port = -1
[  444.07] autocampars: Sensors map read from the sysfs: [none, none, none, 
none],[none, none, none, none],[none, none, none, none],[none, none, none, none]
[  444.12] autocampars: get_application_mode()->4369
[  444.17] autocampars: Detecting sensors for MT9P006
[  444.20] autocampars: Got --init command for already initialized camera, 
trying to re-initialize
[  444.22] autocampars: after reset - current frame on master port =
[  444.25] autocampars: Reset camera state to BITSTREAM
[  444.33] autocampars: ports:
[  444.35] autocampars: System FPGA version:   0x039300da
[  444.38] autocampars: Sensor interface type: PAR12
[  444.45] autocampars: Detected sensors: [none, none, none, none],[none, none, 
none, none],[none, none, none, none],[none, none, none, none]
[  444.48] autocampars: Reached state: SENSORS_DETECTED
[  444.53] autocampars: Disabling sensor port  0
[  444.56] autocampars: Disabling sensor port  1
[  444.58] autocampars: Disabling sensor port  2
[  444.61] autocampars: Disabling sensor port  3
[  444.69] autocampars: Frames: -1, -1, -1, -1
[  444.71] autocampars: Reached state: SENSORS_SYNCHRONIZED
[  444.74] autocampars: ports:
[  444.81] autocampars: init_cameras() start: camera_state=SENSORS_SYNCHRONIZED
[  444.86] autocampars: Collected gammas == Array
(
)


[  444.89] autocampars: will need to skip local  frames
[  444.92] autocampars: Reached state PARAMETERS_PRESET
[  444.94] autocampars: Skipping  frames
[  444.97] autocampars: Frame delay = 0 s
[  445.02] autocampars: Remaining trigger parameters: 


Warning: array_key_exists() expects parameter 2 to be array, null given in 
/usr/bin/autocampars.php on line 1074


Warning: array_key_exists() expects parameter 2 to be array, null given in 
/usr/bin/autocampars.php on line 1085


Warning: array_key_exists() expects parameter 2 to be array, null given in 
/usr/bin/autocampars.php on line 1086


Warning: array_key_exists() expects parameter 2 to be array, null given in 
/usr/bin/autocampars.php on line 1091


Warning: elphel_set_P_arr() expects parameter 2 to be array, null given in 
/usr/bin/autocampars.php on line 1095
[  445.09] autocampars: Skipping   more frames
[  445.14] autocampars: Reached state PARAMETERS_PRESET
[  445.17] autocampars: Reached state INITIALIZED
[  445.20] autocampars: Sensors on ports:  were successfully initialized
[  445.22] autocampars: INITIALIZED
[  445.25] autocampars: revisions differ
[  445.27] autocampars: Log file saved as /var/log/autocampars.log
[  445.32] init_elphel393: init SATA
[  445.32] init_elphel393: 10389 was not detected: skipping SATA init
[  445.32] init_elphel393: Start GPS and event logger
Initializing Exif template: /www/pages/exif.php init noGPS nocompass
[  445.75] init_elphel393: /var/volatile/state already exists
[  445.75] init_elphel393: DONE, log file: /var/log/init_elphel393.log





This is the output from init_elphel393.py when only the 14 Mpix sensor is 
connected:
[   45.92] init_elphel393: Fan on
[   45.93] init_elphel393: Initialize USB hub
[   45.94] init_elphel393: 10389 was not detected: skipping USB hub init
[   45.94] init_elphel393: init_elphel393.py: ip = 192.168.0.9, mask = 
255.255.255.0
[   45.95] init_elphel393: init_elphel393.py: imgsrv
Set port number: 2323
Set port number: 2324
Set port number: 2325
Set port number: 2326
[   46.34] init_elphel393: init_elphel393.py: auto exposure daemon
autoexposure#0 started, daemon_bit=0x0, debug=0x1
autoexposure#1 started, daemon_bit=0x0, debug=0x1
autoexposure#2 started, daemon_bit=0x0, debug=0x1
autoexposure.c:141:main: autoexposure#2: drivers initialized
autoexposure.c:146:main: autoexposure#2 started daemon_bit=0x0, debug=0x1
autoexposure.c:154:main: autoexposure#2 this_frame = 0xe2
autoexposure.c:157:main: frame 14: autoexposure#2 this_frame = 0xe2
autoexposure#3 started, daemon_bit=0x0, debug=0x1
[   46.58] autocampars: Processing camera state: INITIALIZED
[   46.63] autocampars: Active sensor ports: 2 master_port = 2
[   46.66] autocampars: Sensors map read from the sysfs: [none, none, none, 
none],[none, none, none, none],[mt9p006, none, none, none],[none, none, none, 
none]
[   46.71] autocampars: get_application_mode()->4369
[   46.76] autocampars: Detecting sensors for MT9P006
[   46.79] autocampars: Got --init command for already initialized camera, 
trying to re-initialize
[   46.81] autocampars: Current frame on master port =230, sleeping to give 
daemons a chance
[   51.84] autocampars: Current frame on master port =280, waking up, daemons 
should be dead already
[   51.87] autocampars: after reset - current frame on master port =281
[   51.89] autocampars: Reset camera state to BITSTREAM
[   51.97] autocampars: ports:2
[   52.02] autocampars: Started detection for sensor port 2
[   52.05] autocampars: System FPGA version:   0x039300da
[   52.07] autocampars: Sensor interface type: PAR12
[   52.15] autocampars: Detected sensors: [none, none, none, none],[none, none, 
none, none],[mt9p006, none, none, none],[none, none, none, none]
[   52.17] autocampars: Reached state: SENSORS_DETECTED
[   52.43] autocampars: Disabling sensor port  0
[   52.45] autocampars: Disabling sensor port  1
[   52.48] autocampars: Disabling sensor port  3
[   52.66] autocampars: Frames: -1, -1, 0, -1
[   52.68] autocampars: Reached state: SENSORS_SYNCHRONIZED
[   52.71] autocampars: ports:2
[   52.76] autocampars: autocampars.php parsed configuration file 
/etc/elphel393/autocampars2.xml.
[   52.84] autocampars: init_cameras() start: camera_state=SENSORS_SYNCHRONIZED
[   52.89] autocampars: Collected gammas == Array
(
    [2617] => 1
)


[   52.95] autocampars: port 2 setting @1 init exposure: EXPOS= 1000
[   53.05] autocampars: port 2 setting @8 restoring exposure: EXPOS= 10000
[   53.08] autocampars: will need to skip local 7 frames
[   53.10] autocampars: Reached state PARAMETERS_PRESET
[   53.13] autocampars: Skipping 7 frames
[   53.15] autocampars: Frame delay = 0.1 s
aexp_utils.c:140:getPercentile: ERROR Requested histograms for frame 7 (0x7) 
are not available. this_frame=0x8, now=0x8
autoexposure.c:241:main: ERROR (port 2): Restarting autoexposure due to errors, 
skipping a frame
aexp_utils.c:140:getPercentile: ERROR Requested histograms for frame 8 (0x8) 
are not available. this_frame=0x9, now=0x9
autoexposure.c:241:main: ERROR (port 2): Restarting autoexposure due to errors, 
skipping a frame
[   54.62] autocampars: Started camera in periodic self-triggered mode, period 
= 0.1 s
[   54.65] autocampars: Reached state PARAMETERS_PRESET
[   54.68] autocampars: Reached state INITIALIZED
[   54.70] autocampars: Sensors on ports: 2 were successfully initialized
aexp_utils.c:140:getPercentile: ERROR Requested histograms for frame 9 (0x9) 
are not available. this_frame=0xa, now=0xa
autoexposure.c:241:main: ERROR (port 2): Restarting autoexposure due to errors, 
skipping a frame
[   54.73] autocampars: INITIALIZED
[   54.75] autocampars: Log file saved as /var/log/autocampars.log
[   54.81] init_elphel393: init SATA
aexp_utils.c:140:getPercentile: ERROR Requested histograms for frame 10 (0xa) 
are not available. this_frame=0xb, now=0xb
autoexposure.c:241:main: ERROR (port 2): Restarting autoexposure due to errors, 
skipping a frame
[   54.81] init_elphel393: 10389 was not detected: skipping SATA init
[   54.81] init_elphel393: Start GPS and event logger
aexp_utils.c:140:getPercentile: ERROR Requested histograms for frame 11 (0xb) 
are not available. this_frame=0xc, now=0xc
autoexposure.c:241:main: ERROR (port 2): Restarting autoexposure due to errors, 
skipping a frame
Initializing Exif template: /www/pages/exif.php init noGPS nocompass
[   55.24] init_elphel393: /var/volatile/state already exists
[   55.24] init_elphel393: DONE, log file: /var/log/init_elphel393.log



Any assistance in resolving this would be greatly appreciated.



Kind regards,

Richard Rigby
Software Developer




www.redzone.com



 Ph: +64 9 479 9901
Fax: +64 9 479 9904


13 Tarndale Grove • Albany • Auckland 0632 • New Zealand
















 
 




_______________________________________________
Support-list mailing list
Support-list@support.elphel.com
http://support.elphel.com/mailman/listinfo/support-list_support.elphel.com

Reply via email to