Hi, 14MPx is not yet supported in the current firmware but I'm working on the driver at the moment - hopefully will have something within a couple weeks. There's an old firmware where exposure, gains and lane phases can be set, not much more.
Best regards, Oleg Dzhimiev Electronics Engineer phone: +1 801 783 5555 x124 Elphel, Inc. On Fri, Feb 23, 2018 at 11:23 AM, Andrey Filippov <and...@elphel.com> wrote: > > > == == == == == == Forwarded message == == == == == == > From : Richard Rigby<rri...@redzone.com> > To : <support-l...@elphel.com> > Date : Thu, 22 Feb 2018 18:28:08 -0800 > Subject : 14Mpix sensor not detected > == == == == == == Forwarded message == == == == == == > > Hello, > > I have a 393 board as well as one 5 Mpix sensor and one 14 Mpix sensor. > However only the 5Mpix sensor is working. > > I am using the web interface to view the camera. > > I have tried to run the init_elphel393.py script for both sensors and it > looks to me that the 14 Mpix sensor cannot be detected. > > This is the output from init_elphel393.py when only the 14 Mpix sensor is > connected: > [ 443.35] init_elphel393: Fan on > [ 443.36] init_elphel393: Initialize USB hub > [ 443.37] init_elphel393: 10389 was not detected: skipping USB hub init > [ 443.37] init_elphel393: init_elphel393.py: ip = 192.168.0.9, mask = > 255.255.255.0 > [ 443.38] init_elphel393: init_elphel393.py: imgsrv > Set port number: 2323 > Set port number: 2324 > Set port number: 2325 > Set port number: 2326 > [ 443.77] init_elphel393: init_elphel393.py: auto exposure daemon > autoexposure#0 started, daemon_bit=0x0, debug=0x1 > autoexposure#1 started, daemon_bit=0x0, debug=0x1 > autoexposure#2 started, daemon_bit=0x0, debug=0x1 > autoexposure#3 started, daemon_bit=0x0, debug=0x1 > [ 443.99] autocampars: Processing camera state: INITIALIZED > [ 444.05] autocampars: Active sensor ports: master_port = -1 > [ 444.07] autocampars: Sensors map read from the sysfs: [none, none, > none, none],[none, none, none, none],[none, none, none, none],[none, none, > none, none] > [ 444.12] autocampars: get_application_mode()->4369 > [ 444.17] autocampars: Detecting sensors for MT9P006 > [ 444.20] autocampars: Got --init command for already initialized > camera, trying to re-initialize > [ 444.22] autocampars: after reset - current frame on master port = > [ 444.25] autocampars: Reset camera state to BITSTREAM > [ 444.33] autocampars: ports: > [ 444.35] autocampars: *System FPGA version: 0x039300da* > [ 444.38] autocampars: *Sensor interface type: PAR12* > [ 444.45] autocampars: *Detected sensors: [none, none, none, > none],[none, none, none, none],[none, none, none, none],[none, none, none, > none]* > [ 444.48] autocampars: Reached state: SENSORS_DETECTED > [ 444.53] autocampars: Disabling sensor port 0 > [ 444.56] autocampars: Disabling sensor port 1 > [ 444.58] autocampars: Disabling sensor port 2 > [ 444.61] autocampars: Disabling sensor port 3 > [ 444.69] autocampars: Frames: -1, -1, -1, -1 > [ 444.71] autocampars: Reached state: SENSORS_SYNCHRONIZED > [ 444.74] autocampars: ports: > [ 444.81] autocampars: init_cameras() start: camera_state=SENSORS_ > SYNCHRONIZED > [ 444.86] autocampars: Collected gammas == Array > ( > ) > > [ 444.89] autocampars: will need to skip local frames > [ 444.92] autocampars: Reached state PARAMETERS_PRESET > [ 444.94] autocampars: Skipping frames > [ 444.97] autocampars: Frame delay = 0 s > [ 445.02] autocampars: Remaining trigger parameters: > > Warning: array_key_exists() expects parameter 2 to be array, null given in > /usr/bin/autocampars.php on line 1074 > > Warning: array_key_exists() expects parameter 2 to be array, null given in > /usr/bin/autocampars.php on line 1085 > > Warning: array_key_exists() expects parameter 2 to be array, null given in > /usr/bin/autocampars.php on line 1086 > > Warning: array_key_exists() expects parameter 2 to be array, null given in > /usr/bin/autocampars.php on line 1091 > > Warning: elphel_set_P_arr() expects parameter 2 to be array, null given in > /usr/bin/autocampars.php on line 1095 > [ 445.09] autocampars: Skipping more frames > [ 445.14] autocampars: Reached state PARAMETERS_PRESET > [ 445.17] autocampars: Reached state INITIALIZED > [ 445.20] autocampars: Sensors on ports: were successfully initialized > [ 445.22] autocampars: *INITIALIZED* > [ 445.25] autocampars: *revisions differ* > [ 445.27] autocampars: *Log file saved as /var/log/autocampars.log* > [ 445.32] init_elphel393: init SATA > [ 445.32] init_elphel393: 10389 was not detected: skipping SATA init > [ 445.32] init_elphel393: Start GPS and event logger > Initializing Exif template: /www/pages/exif.php init noGPS nocompass > [ 445.75] init_elphel393: /var/volatile/state already exists > [ 445.75] init_elphel393: *DONE, log file: /var/log/init_elphel393.log* > > > This is the output from init_elphel393.py when only the 14 Mpix sensor is > connected: > [ 45.92] init_elphel393: Fan on > [ 45.93] init_elphel393: Initialize USB hub > [ 45.94] init_elphel393: 10389 was not detected: skipping USB hub init > [ 45.94] init_elphel393: init_elphel393.py: ip = 192.168.0.9, mask = > 255.255.255.0 > [ 45.95] init_elphel393: init_elphel393.py: imgsrv > Set port number: 2323 > Set port number: 2324 > Set port number: 2325 > Set port number: 2326 > [ 46.34] init_elphel393: init_elphel393.py: auto exposure daemon > autoexposure#0 started, daemon_bit=0x0, debug=0x1 > autoexposure#1 started, daemon_bit=0x0, debug=0x1 > autoexposure#2 started, daemon_bit=0x0, debug=0x1 > autoexposure.c:141:main: autoexposure#2: drivers initialized > autoexposure.c:146:main: autoexposure#2 started daemon_bit=0x0, debug=0x1 > autoexposure.c:154:main: autoexposure#2 this_frame = 0xe2 > autoexposure.c:157:main: frame 14: autoexposure#2 this_frame = 0xe2 > autoexposure#3 started, daemon_bit=0x0, debug=0x1 > [ 46.58] autocampars: Processing camera state: INITIALIZED > [ 46.63] autocampars: Active sensor ports: 2 master_port = 2 > [ 46.66] autocampars: Sensors map read from the sysfs: [none, none, > none, none],[none, none, none, none],[mt9p006, none, none, none],[none, > none, none, none] > [ 46.71] autocampars: get_application_mode()->4369 > [ 46.76] autocampars: Detecting sensors for MT9P006 > [ 46.79] autocampars: Got --init command for already initialized > camera, trying to re-initialize > [ 46.81] autocampars: Current frame on master port =230, sleeping to > give daemons a chance > [ 51.84] autocampars: Current frame on master port =280, waking up, > daemons should be dead already > [ 51.87] autocampars: after reset - current frame on master port =281 > [ 51.89] autocampars: Reset camera state to BITSTREAM > [ 51.97] autocampars: ports:2 > [ 52.02] autocampars: Started detection for sensor port 2 > [ 52.05] autocampars: *System FPGA version: 0x039300da* > [ 52.07] autocampars: *Sensor interface type: PAR12* > [ 52.15] autocampars: *Detected sensors: [none, none, none, > none],[none, none, none, none],[mt9p006, none, none, none],[none, none, > none, none]* > [ 52.17] autocampars: Reached state: SENSORS_DETECTED > [ 52.43] autocampars: Disabling sensor port 0 > [ 52.45] autocampars: Disabling sensor port 1 > [ 52.48] autocampars: Disabling sensor port 3 > [ 52.66] autocampars: Frames: -1, -1, 0, -1 > [ 52.68] autocampars: Reached state: SENSORS_SYNCHRONIZED > [ 52.71] autocampars: ports:2 > [ 52.76] autocampars: autocampars.php parsed configuration file > /etc/elphel393/autocampars2.xml. > [ 52.84] autocampars: init_cameras() start: camera_state=SENSORS_ > SYNCHRONIZED > [ 52.89] autocampars: Collected gammas == Array > ( > [2617] => 1 > ) > > [ 52.95] autocampars: port 2 setting @1 init exposure: EXPOS= 1000 > [ 53.05] autocampars: port 2 setting @8 restoring exposure: EXPOS= 10000 > [ 53.08] autocampars: will need to skip local 7 frames > [ 53.10] autocampars: Reached state PARAMETERS_PRESET > [ 53.13] autocampars: Skipping 7 frames > [ 53.15] autocampars: Frame delay = 0.1 s > aexp_utils.c:140:getPercentile: ERROR Requested histograms for frame 7 > (0x7) are not available. this_frame=0x8, now=0x8 > autoexposure.c:241:main: ERROR (port 2): Restarting autoexposure due to > errors, skipping a frame > aexp_utils.c:140:getPercentile: ERROR Requested histograms for frame 8 > (0x8) are not available. this_frame=0x9, now=0x9 > autoexposure.c:241:main: ERROR (port 2): Restarting autoexposure due to > errors, skipping a frame > [ 54.62] autocampars: *Started camera in periodic self-triggered mode, > period = 0.1 s* > [ 54.65] autocampars: Reached state PARAMETERS_PRESET > [ 54.68] autocampars: Reached state INITIALIZED > [ 54.70] autocampars: Sensors on ports: 2 were successfully initialized > aexp_utils.c:140:getPercentile: ERROR Requested histograms for frame 9 > (0x9) are not available. this_frame=0xa, now=0xa > autoexposure.c:241:main: ERROR (port 2): Restarting autoexposure due to > errors, skipping a frame > [ 54.73] autocampars: *INITIALIZED* > [ 54.75] autocampars: *Log file saved as /var/log/autocampars.log* > [ 54.81] init_elphel393: init SATA > aexp_utils.c:140:getPercentile: ERROR Requested histograms for frame 10 > (0xa) are not available. this_frame=0xb, now=0xb > autoexposure.c:241:main: ERROR (port 2): Restarting autoexposure due to > errors, skipping a frame > [ 54.81] init_elphel393: 10389 was not detected: skipping SATA init > [ 54.81] init_elphel393: Start GPS and event logger > aexp_utils.c:140:getPercentile: ERROR Requested histograms for frame 11 > (0xb) are not available. this_frame=0xc, now=0xc > autoexposure.c:241:main: ERROR (port 2): Restarting autoexposure due to > errors, skipping a frame > Initializing Exif template: /www/pages/exif.php init noGPS nocompass > [ 55.24] init_elphel393: /var/volatile/state already exists > [ 55.24] init_elphel393: *DONE, log file: /var/log/init_elphel393.log* > > Any assistance in resolving this would be greatly appreciated. > > > Kind regards, > > *Richard Rigby* > Software Developer > > > www.redzone.com > > Ph: +64 9 479 9901 > > Fax: +64 9 479 9904 > > > 13 Tarndale Grove • Albany • Auckland 0632 • New Zealand > > > > > > _______________________________________________ > Support-list mailing list > Support-list@support.elphel.com > http://support.elphel.com/mailman/listinfo/support-list_support.elphel.com >
_______________________________________________ Support-list mailing list Support-list@support.elphel.com http://support.elphel.com/mailman/listinfo/support-list_support.elphel.com