Only problems I've had with carp recently weren't actually due to carp, but the dhcp daemon. There's a hold down timer somewhere that won't let it come up as primary for 300 or 360 seconds (my bet is there two different timeouts, a 60 second timeout and a 300 second one). So if you're running a highly available DHCP server on your pfSense box, keep this in mind - don't reboot both within about 10 minutes of each other for now.
--Bill On 9/27/05, Holger Bauer <[EMAIL PROTECTED]> wrote: > I have a working carp config at home. Have failed over several times the last > days, with 0.85.2 and 0.85.4 no session was dropped (I even was tunnelling > from a client behind the carpmachines to the office). DNS and DHCP is > configured for failover as well. I haven't seen any issues so far. Anybody > else seeing having problems? Strange. > > Holger > > > > -----Ursprüngliche Nachricht----- > Von: Frimmel, Ivan (ISS South Africa) [mailto:[EMAIL PROTECTED] > Gesendet: Dienstag, 27. September 2005 11:47 > An: [email protected] > Betreff: RE: [pfSense Support] 050.2 CARP won't go Master or Backup > > > HI > > Yes .. 085.2 .. 085.4 does the same too. Enable / disable does not work ... > goes to init always. 0.85 worked.. did an upgrade to 085.2 it stopped > working. I deleted all carp entries and re-setup from scratch. I will try > update_file.sh and let you know results. > > Tx > Ivan > > > -----Original Message----- > From: Holger Bauer [mailto:[EMAIL PROTECTED] > Sent: Monday, September 26, 2005 10:55 AM > To: [email protected] > Subject: AW: [pfSense Support] 050.2 CARP won't go Master or Backup > > 0.50.2? I guess you are talking about 0.85.2, if not upgrade! ;-) > > I only have experienced such problems if the carpinterfaces didn't match the > real ip/subnet-range of the real interface the carp interface is running on. > Another thing to try is to manually disable and enable CARP at > Status>CARP(failover) in the webgui. If it's working after that there might > be a problem bringing up everything in the right order. > > There also have been some changes to CARP lately. You might want to run > "update_file.sh -all" from the shell to grab the latest changes. > > Holger > > > > -----Ursprüngliche Nachricht----- > Von: Frimmel, Ivan (ISS South Africa) [mailto:[EMAIL PROTECTED] > Gesendet: Montag, 26. September 2005 09:34 > An: [email protected] > Betreff: [pfSense Support] 050.2 CARP won't go Master or Backup > > > HI > > I have Carp running successfully on 0.50. Upgraded yesterday to 050.2 > and CARP absolutely refuses to start. OPT1 is up. PPPoE is UP. CARP goes > to INIT and does not ever go master or backup. > > I deleted all CARP configs and recreated everything from scratch. On > both boxes CARP will not start. Hitting Disable / enable makes it go > from disable to INIT.. but never starts. Even tried doing everything > with the second box physically turned off. No difference. > > Any ideas? > Tx > Ivan. > > > --------------------------------------------------------------------- > To unsubscribe, e-mail: [EMAIL PROTECTED] > For additional commands, e-mail: [EMAIL PROTECTED] > > ____________ > Virus checked by G DATA AntiVirusKit > > > --------------------------------------------------------------------- > To unsubscribe, e-mail: [EMAIL PROTECTED] > For additional commands, e-mail: [EMAIL PROTECTED] > > > --------------------------------------------------------------------- > To unsubscribe, e-mail: [EMAIL PROTECTED] > For additional commands, e-mail: [EMAIL PROTECTED] > > > ____________ > Virus checked by G DATA AntiVirusKit > > > --------------------------------------------------------------------- > To unsubscribe, e-mail: [EMAIL PROTECTED] > For additional commands, e-mail: [EMAIL PROTECTED] > > --------------------------------------------------------------------- To unsubscribe, e-mail: [EMAIL PROTECTED] For additional commands, e-mail: [EMAIL PROTECTED]
