I'll have new images posted real soon on the FreeBSD-6 release version. I'm hoping to see the released version sometime today or tomorrow.
Scott On 10/28/05, Sönke Schau <[EMAIL PROTECTED]> wrote: > Hello! > I just got a WRAP 1E-2 Board and trying to get PFSense to run. > Unfortunately the system does not come up: it just panics during startup. > My first thought was that the problem is related to the used CF-Card. > I tried anotherone from a different manufacturer, but it didn't help. > Switching between CHS and LBA Mode in the BIOS didn't help either. > One thing i recognized is, that physdiskwrite notes different values for CHS > than the BIOS on its initial message. > Desperate as i was i tried an image of WRAPCOP (IPCOP for WRAP) and it ran. > So the hardware seems to be working. > > Has anyone an idea? > > Best regards > Soenke Schau > > PC Engines WRAP.1C/1D/1E v1.08 > 640 KB Base Memory > 130048 KB Extended Memory > > 01F0 Master 848A SanDisk SDCFB-256 > Phys C/H/S 695/15/48 Log C/H/S 248/32/63 Copyright (c) 1992-2005 The FreeBSD > Project. > Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994 > The Regents of the University of California. All rights reserved. > FreeBSD 6.0-RC1 #0: Thu Oct 20 03:37:59 UTC 2005 > [EMAIL PROTECTED]:/usr/obj/usr/src/sys/pfSense_wrap.6 > Timecounter "i8254" frequency 1193182 Hz quality 0 > CPU: Geode(TM) Integrated Processor by National Semi (266.66-MHz 586-class > CPU) > Origin = "Geode by NSC" Id = 0x540 Stepping = 0 > Features=0x808131<FPU,TSC,MSR,CX8,CMOV,MMX> > real memory = 134217728 (128 MB) > avail memory = 121913344 (116 MB) > wlan: mac acl policy registered > ath_hal: 0.9.14.9 (AR5210, AR5211, AR5212, RF5111, RF5112, RF2413) > npx0: [FAST] > npx0: <math processor> on motherboard > npx0: INT 16 interface > cpu0 on motherboard > pcib0: <Host to PCI bridge> pcibus 0 on motherboard > pci0: <PCI bus> on pcib0 > sis0: <NatSemi DP8381[56] 10/100BaseTX> port 0x1000-0x10ff mem > 0x80000000-0x8000 0fff irq 10 at device 14.0 on pci0 > sis0: Silicon Revision: DP83816A > miibus0: <MII bus> on sis0 > ukphy0: <Generic IEEE 802.3u media interface> on miibus0 > ukphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto > sis0: Ethernet address: 00:0d:b9:02:7c:64 > sis1: <NatSemi DP8381[56] 10/100BaseTX> port 0x1400-0x14ff mem > 0x80040000-0x8004 > 0fff irq 9 at device 15.0 on pci0 > sis1: Silicon Revision: DP83816A > miibus1: <MII bus> on sis1 > ukphy1: <Generic IEEE 802.3u media interface> on miibus1 > ukphy1: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto > sis1: Ethernet address: 00:0d:b9:02:7c:65 > sis2: <NatSemi DP8381[56] 10/100BaseTX> port 0x1800-0x18ff mem > 0x80080000-0x8008 > 0fff irq 11 at device 16.0 on pci0 > sis2: Silicon Revision: DP83816A > miibus2: <MII bus> on sis2 > ukphy2: <Generic IEEE 802.3u media interface> on miibus2 > ukphy2: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto > sis2: Ethernet address: 00:0d:b9:02:7c:66 Geode GPIO@ = f400 Geode PC > Engines WRAP.1C/1D/1E v1.tinyBIOS V1.4a (C)1997-2005 > isab0: <PCI-ISA bridge> port 0xf400-0xf43f,0xf600-0xf63f at device 18.0 on > pci0 > isa0: <ISA bus> on isab0 > pci0: <bridge> at device 18.1 (no driver attached) > atapci0: <National Geode SC1100 ATA33 controller> port > 0x1f0-0x1f7,0x3f6,0x170-0 x177,0x376,0xfc00-0xfc0f at device 18.2 on pci0 > ata0: <ATA channel 0> on atapci0 > ata1: <ATA channel 1> on atapci0 > pci0: <multimedia, audio> at device 18.3 (no driver attached) Geode CBA@ > 0x9000 Geode rev: 06 03 Timecounter "Geode" frequency 27000000 Hz quality > 1000 > pci0: <bridge> at device 18.5 (no driver attached) pmtimer0 on isa0 > orm0: <ISA Option ROM> at iomem 0xe0000-0xe7fff on isa0 > ppc0: parallel port not found. > sio0 at port 0x3f8-0x3ff irq 4 flags 0x10 on isa0 > sio0: type 16550A, console > sio1: configured irq 3 not in bitmap of probed irqs 0 > sio1: port may not be enabled > RTC BIOS diagnostic error 80<clock_battery> Timecounters tick every 1.000 > msec Fast IPsec: Initialized Security Association Processing. > ad0: 244MB <SanDisk SDCFB-256 Rev 0.00> at ata0-master PIO4 Trying to mount > root from ufs:/dev/ad0a > > pid 46 (sh), uid 0: exited on signal 11 > > > Fatal trap 12: page fault while in kernel mode > fault virtual address = 0x2014 > fault code = supervisor write, page not present > instruction pointer = 0x20:0xc0702a51 > stack pointer = 0x28:0xc7979828 > frame pointer = 0x28:0xc7979840 > code segment = base 0x0, limit 0xfffff, type 0x1b > = DPL 0, pres 1, def32 1, gran 1 > processor eflags = interrupt enabled, resume, IOPL = 0 > current process = 1 (init) > trap number = 12 > panic: page fault > Uptime: 2s > Cannot dump. No dump device defined. > Automatic reboot in 15 seconds - press a key on the console to abort > > > --------------------------------------------------------------------- To unsubscribe, e-mail: [EMAIL PROTECTED] For additional commands, e-mail: [EMAIL PROTECTED]
