I just tried the same image and it seems to be fine:
# ifconfig ath0
ath0: flags=8943<UP,BROADCAST,RUNNING,PROMISC,SIMPLEX,MULTICAST> mtu 1500
inet6 fe80::20b:6bff:fe34:aed0%ath0 prefixlen 64 scopeid 0x1
ether 00:0b:6b:34:ae:d0
media: IEEE 802.11 Wireless Ethernet autoselect mode 11b <hostap>
status: associated
ssid maconbacon channel 2 bssid 00:0b:6b:34:ae:d0
authmode WPA privacy MIXED deftxkey 3 TKIP 2:128-bit TKIP 3:128-bit
txpowmax 40 protmode CTS -apbridge dtimperiod 1 bintval 100
Scott
On 12/18/05, Luciano La Delfa <[EMAIL PROTECTED]> wrote:
> Hi,
> I've installed on my Soekris Net4801 the Atheros (Model Ag-621) wireless
> minipci card.
> It's not working and this is the message I get during boot.
>
> ath0: <Atheros 5212> mem 0xa0010000-0xa001ffff irq 11 at device 14.0 on pci0
> ath0: unable to attach hardware; HAL status 14
> device_attach: ath0 attach returned 6
>
>
> Regards,
> Luciano
>
>
> more dmesg.boot
>
> Copyright (c) 1992-2005 The FreeBSD Project.
> Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
> The Regents of the University of California. All rights reserved.
> FreeBSD 6.0-STABLE #0: Mon Dec 12 23:50:27 UTC 2005
> [EMAIL PROTECTED]:/usr/obj.pfSense/usr/src/sys/pfSense_wrap.6
> Timecounter "i8254" frequency 1193182 Hz quality 0
> CPU: Geode(TM) Integrated Processor by National Semi (266.65-MHz 586-class
> CPU)
> Origin = "Geode by NSC" Id = 0x540 Stepping = 0
> Features=0x808131<FPU,TSC,MSR,CX8,CMOV,MMX>
> real memory = 134217728 (128 MB)
> avail memory = 121905152 (116 MB)
> wlan: mac acl policy registered
> ath_hal: 0.9.16.3 (AR5210, AR5211, AR5212, RF5111, RF5112, RF2413, RF5413,
> DFS)
> npx0: [FAST]
> npx0: <math processor> on motherboard
> npx0: INT 16 interface
> cpu0 on motherboard
> pcib0: <Host to PCI bridge> pcibus 0 on motherboard
> pci0: <PCI bus> on pcib0
> sis0: <NatSemi DP8381[56] 10/100BaseTX> port 0xe100-0xe1ff mem
> 0xa0000000-0xa000
> 0fff irq 10 at device 6.0 on pci0
> sis0: Silicon Revision: DP83816A
> miibus0: <MII bus> on sis0
> ukphy0: <Generic IEEE 802.3u media interface> on miibus0
> ukphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
> sis0: Ethernet address: 00:00:24:c4:80:00
> sis1: <NatSemi DP8381[56] 10/100BaseTX> port 0xe200-0xe2ff mem
> 0xa0001000-0xa000
> 1fff irq 10 at device 7.0 on pci0
> sis1: Silicon Revision: DP83816A
> miibus1: <MII bus> on sis1
> ukphy1: <Generic IEEE 802.3u media interface> on miibus1
> ukphy1: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
> sis1: Ethernet address: 00:00:24:c4:80:01
> sis2: <NatSemi DP8381[56] 10/100BaseTX> port 0xe300-0xe3ff mem
> 0xa0002000-0xa000
> 2fff irq 10 at device 8.0 on pci0
> sis2: Silicon Revision: DP83816A
> miibus2: <MII bus> on sis2
> ukphy2: <Generic IEEE 802.3u media interface> on miibus2
> ukphy2: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
> sis2: Ethernet address: 00:00:24:c4:80:02
> ath0: <Atheros 5212> mem 0xa0010000-0xa001ffff irq 11 at device 14.0 on pci0
> ath0: unable to attach hardware; HAL status 14
> device_attach: ath0 attach returned 6
> Geode GPIO@ = 6100
> Geode Soekris net4801 comBIOS ver. 1.27 20041122 Copyright (C) 2000-2004
> isab0: <PCI-ISA bridge> port 0x6100-0x613f,0x6200-0x623f at device 18.0 on
> pci0
> isa0: <ISA bus> on isab0
> pci0: <bridge> at device 18.1 (no driver attached)
> atapci0: <National Geode SC1100 ATA33 controller> port
> 0x1f0-0x1f7,0x3f6,0x170-0
> x177,0x376,0xe000-0xe00f at device 18.2 on pci0
> ata0: <ATA channel 0> on atapci0
> ata1: <ATA channel 1> on atapci0
> Geode CBA@ 0x6000
> Geode rev: 06 03
> Timecounter "Geode" frequency 27000000 Hz quality 1000
> pci0: <bridge> at device 18.5 (no driver attached)
> ohci0: <OHCI (generic) USB controller> mem 0xa0820000-0xa0820fff irq 5 at
> device
> 19.0 on pci0
> ohci0: [GIANT-LOCKED]
> usb0: OHCI version 1.0, legacy support
> usb0: <OHCI (generic) USB controller> on ohci0
> usb0: USB revision 1.0
> uhub0: (0x0e11) OHCI root hub, class 9/0, rev 1.00/1.00, addr 1
> uhub0: 3 ports with 3 removable, self powered
> pmtimer0 on isa0
> orm0: <ISA Option ROM> at iomem 0xc8000-0xd0fff on isa0
> ppc0: parallel port not found.
> sio0 at port 0x3f8-0x3ff irq 4 flags 0x30 on isa0
> sio0: type 16550A, console
> sio1 at port 0x2f8-0x2ff irq 3 on isa0
> sio1: type 16550A
> Timecounters tick every 1.000 msec
> Fast IPsec: Initialized Security Association Processing.
> ad0: 122MB <SanDisk SDCFH-128 FhDA0145> at ata0-master PIO4
> GEOM_LABEL: Label for provider ad0a is ufs/pfSense.
> GEOM_LABEL: Label for provider ad0d is ufs/pfSenseCfg.
> Trying to mount root from ufs:/dev/ufs/pfSense
>
>
> ---------------------------------------------------------------------
> To unsubscribe, e-mail: [EMAIL PROTECTED]
> For additional commands, e-mail: [EMAIL PROTECTED]
>
>
---------------------------------------------------------------------
To unsubscribe, e-mail: [EMAIL PROTECTED]
For additional commands, e-mail: [EMAIL PROTECTED]
