Hi,
thanks for your quick response. I´ve attached the output of dmesg and
ifconfig to this mail.
the card is reported in dmesg:
wlan: mac acl policy registered
ath_hal: 0.9.16.16 (AR5210, AR5211, AR5212, RF5111, RF5112, RF2413, RF5413)
cpu0 on motherboard
pcib0: <Host to PCI bridge> pcibus 0 on motherboard
pci0: <PCI bus> on pcib0
pci0: <network> at device 13.0 (no driver attached)
ifconfig has also no output on additional interfaces (see attachment).
Espen Johansen schrieb:
> Does dmesg report the card at all ?
> It's Atheros based so it should show up as ath0.
> Does ifconfig list it ?
> Please provide more info.
>
> -lsf
>
> On 4/19/07, Christian Veith <[EMAIL PROTECTED]> wrote:
>> Hi Folks,
>>
>> is it possible to use the Intel Pro/Wireless 2915ABG as an access point
>> with pfsense embedded ?
>>
>> i?ve just installed the card on my wrap but there are no new interfaces
>> in the interface assignment.
>>
>>
>>
>> Everything i found on the forum was that post from 9th of April 2006:
>>
>> http://forum.pfsense.org/index.php/topic,977.msg5975.html#msg5975
>>
>>
>>
>> What could i do to get it working ?
>>
>>
>>
>> kind regards
>>
>> Christian
>>
>> ---------------------------------------------------------------------
>> To unsubscribe, e-mail: [EMAIL PROTECTED]
>> For additional commands, e-mail: [EMAIL PROTECTED]
>>
>>
>
> ---------------------------------------------------------------------
> To unsubscribe, e-mail: [EMAIL PROTECTED]
> For additional commands, e-mail: [EMAIL PROTECTED]
>
>
sis0: flags=8802<BROADCAST,SIMPLEX,MULTICAST> mtu 1500
options=8<VLAN_MTU>
ether 00:0d:b9:06:5b:a0
media: Ethernet autoselect (none)
status: no carrier
sis1: flags=8843<UP,BROADCAST,RUNNING,SIMPLEX,MULTICAST> mtu 1500
options=8<VLAN_MTU>
inet 172.16.0.1 netmask 0xfffffe00 broadcast 172.16.1.255
inet6 fe80::20d:b9ff:fe06:5ba1%sis1 prefixlen 64 scopeid 0x2
ether 00:0d:b9:06:5b:a1
media: Ethernet autoselect (100baseTX <full-duplex>)
status: active
sis2: flags=8843<UP,BROADCAST,RUNNING,SIMPLEX,MULTICAST> mtu 1500
options=8<VLAN_MTU>
inet6 fe80::20d:b9ff:fe06:5ba2%sis2 prefixlen 64 scopeid 0x3
ether 00:0d:b9:06:5b:a2
media: Ethernet autoselect (none)
status: no carrier
lo0: flags=8049<UP,LOOPBACK,RUNNING,MULTICAST> mtu 16384
inet 127.0.0.1 netmask 0xff000000
inet6 ::1 prefixlen 128
inet6 fe80::1%lo0 prefixlen 64 scopeid 0x4
pfsync0: flags=41<UP,RUNNING> mtu 2020
pfsync: syncdev: lo0 maxupd: 128
pflog0: flags=100<PROMISC> mtu 33208
ng0: flags=98d1<UP,POINTOPOINT,RUNNING,NOARP,SIMPLEX,LINK0,MULTICAST> mtu 1500
inet 192.0.2.112 --> 192.0.2.113 netmask 0xffffffff
inet6 fe80::20d:b9ff:fe06:5ba0%ng0 prefixlen 64 scopeid 0x7
tun0: flags=8051<UP,POINTOPOINT,RUNNING,MULTICAST> mtu 1500
inet6 fe80::20d:b9ff:fe06:5ba0%tun0 prefixlen 64 scopeid 0x8
inet 192.168.254.1 --> 192.168.254.2 netmask 0xffffffff
Opened by PID 346
ng1: flags=8890<POINTOPOINT,NOARP,SIMPLEX,MULTICAST> mtu 1500
ng2: flags=8890<POINTOPOINT,NOARP,SIMPLEX,MULTICAST> mtu 1500
ng3: flags=8890<POINTOPOINT,NOARP,SIMPLEX,MULTICAST> mtu 1500
ng4: flags=8890<POINTOPOINT,NOARP,SIMPLEX,MULTICAST> mtu 1500
ng5: flags=8890<POINTOPOINT,NOARP,SIMPLEX,MULTICAST> mtu 1500
ng6: flags=8890<POINTOPOINT,NOARP,SIMPLEX,MULTICAST> mtu 1500
ng7: flags=8890<POINTOPOINT,NOARP,SIMPLEX,MULTICAST> mtu 1500
ng8: flags=8890<POINTOPOINT,NOARP,SIMPLEX,MULTICAST> mtu 1500
ng9: flags=8890<POINTOPOINT,NOARP,SIMPLEX,MULTICAST> mtu 1500
ng10: flags=8890<POINTOPOINT,NOARP,SIMPLEX,MULTICAST> mtu 1500
ng11: flags=8890<POINTOPOINT,NOARP,SIMPLEX,MULTICAST> mtu 1500
ng12: flags=8890<POINTOPOINT,NOARP,SIMPLEX,MULTICAST> mtu 1500
ng13: flags=8890<POINTOPOINT,NOARP,SIMPLEX,MULTICAST> mtu 1500
ng14: flags=8890<POINTOPOINT,NOARP,SIMPLEX,MULTICAST> mtu 1500
ng15: flags=8890<POINTOPOINT,NOARP,SIMPLEX,MULTICAST> mtu 1500
ng16: flags=8890<POINTOPOINT,NOARP,SIMPLEX,MULTICAST> mtu 1500
Timecounter "i8254" frequency 1193182 Hz quality 0
CPU: Geode(TM) Integrated Processor by National Semi (233.32-MHz 586-class CPU)
Origin = "Geode by NSC" Id = 0x540 Stepping = 0
Features=0x808131<FPU,TSC,MSR,CX8,CMOV,MMX>
real memory = 134217728 (128 MB)
avail memory = 121917440 (116 MB)
wlan: mac acl policy registered
ath_hal: 0.9.16.16 (AR5210, AR5211, AR5212, RF5111, RF5112, RF2413, RF5413)
cpu0 on motherboard
pcib0: <Host to PCI bridge> pcibus 0 on motherboard
pci0: <PCI bus> on pcib0
pci0: <network> at device 13.0 (no driver attached)
sis0: <NatSemi DP8381[56] 10/100BaseTX> port 0x1000-0x10ff mem
0x80040000-0x80040fff irq 10 at device 14.0 on pci0
sis0: Silicon Revision: DP83816A
miibus0: <MII bus> on sis0
ukphy0: <Generic IEEE 802.3u media interface> on miibus0
ukphy0: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
sis0: Ethernet address: 00:0d:b9:06:5b:a0
sis1: <NatSemi DP8381[56] 10/100BaseTX> port 0x1400-0x14ff mem
0x80080000-0x80080fff irq 9 at device 15.0 on pci0
sis1: Silicon Revision: DP83816A
miibus1: <MII bus> on sis1
ukphy1: <Generic IEEE 802.3u media interface> on miibus1
ukphy1: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
sis1: Ethernet address: 00:0d:b9:06:5b:a1
sis2: <NatSemi DP8381[56] 10/100BaseTX> port 0x1800-0x18ff mem
0x800c0000-0x800c0fff irq 11 at device 16.0 on pci0
sis2: Silicon Revision: DP83816A
miibus2: <MII bus> on sis2
ukphy2: <Generic IEEE 802.3u media interface> on miibus2
ukphy2: 10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
sis2: Ethernet address: 00:0d:b9:06:5b:a2
Geode GPIO@ = f400
Geode PC Engines WRAP.1C/1D/1E v1.tinyBIOS V1.4a (C)1997-2005
isab0: <PCI-ISA bridge> port 0xf400-0xf43f,0xf600-0xf63f at device 18.0 on pci0
isa0: <ISA bus> on isab0
pci0: <bridge> at device 18.1 (no driver attached)
atapci0: <National Geode SC1100 ATA33 controller> port
0x1f0-0x1f7,0x3f6,0x170-0x177,0x376,0xfc00-0xfc0f at device 18.2 on pci0
ata0: <ATA channel 0> on atapci0
ata1: <ATA channel 1> on atapci0
pci0: <multimedia, audio> at device 18.3 (no driver attached)
Geode CBA@ 0x9000
Geode rev: 06 03
Timecounter "Geode" frequency 27000000 Hz quality 1000
pci0: <bridge> at device 18.5 (no driver attached)
orm0: <ISA Option ROM> at iomem 0xe0000-0xe7fff on isa0
ppc0: parallel port not found.
sio0 at port 0x3f8-0x3ff irq 4 flags 0x30 on isa0
sio0: type 16550A, console
sio1: configured irq 3 not in bitmap of probed irqs 0
sio1: port may not be enabled
RTC BIOS diagnostic error 80<clock_battery>
Timecounters tick every 10.000 msec
Fast IPsec: Initialized Security Association Processing.
ad0: 244MB <TOSHIBA THNCF256MQG 3.00> at ata0-master PIO4
GEOM_LABEL: Label for provider ad0a is ufs/pfSense.
GEOM_LABEL: Label for provider ad0d is ufs/pfSenseCfg.
Trying to mount root from ufs:/dev/ufs/pfSense
sis0: link state changed to DOWN
sis1: link state changed to DOWN
sis2: link state changed to DOWN
sis1: link state changed to UP
pflog0: promiscuous mode enabled
---------------------------------------------------------------------
To unsubscribe, e-mail: [EMAIL PROTECTED]
For additional commands, e-mail: [EMAIL PROTECTED]
