Re: [pfSense Support] Get WLAN Working with Intel Pro/Wireless 2915ABG

Thu, 19 Apr 2007 13:53:33 -0700

That's not an Atheros card. It should be supported by the iwi driver though, we must not have that in the pfsense kernel for some reason? Maybe this is why, from the iwi(4) man page: 


    This driver requires firmware to be loaded before it will work.  
You need

    to install the ports/net/iwi-firmware-kmod port before ifconfig(8) will
    work.



Christian Veith wrote:

Hi,

thanks for your quick response. I´ve attached the output of dmesg and
ifconfig to this mail.

the card is reported in dmesg:

wlan: mac acl policy registered
ath_hal: 0.9.16.16 (AR5210, AR5211, AR5212, RF5111, RF5112, RF2413, RF5413)
cpu0 on motherboard
pcib0: <Host to PCI bridge> pcibus 0 on motherboard
pci0: <PCI bus> on pcib0
pci0: <network> at device 13.0 (no driver attached)



ifconfig has also no output on additional interfaces (see attachment).



Espen Johansen schrieb:

  

Does dmesg report the card at all ?
It's Atheros based so it should show up as ath0.
Does ifconfig list it ?
Please provide more info.

-lsf

On 4/19/07, Christian Veith <[EMAIL PROTECTED]> wrote:

    

Hi Folks,

is it possible to use the Intel Pro/Wireless 2915ABG as an access point
with pfsense embedded ?

i?ve just installed the card on my wrap but there are no new interfaces
in the interface assignment.



Everything i found on the forum was that post from 9th of April 2006:

http://forum.pfsense.org/index.php/topic,977.msg5975.html#msg5975



What could i do to get it working ?



kind regards

Christian

---------------------------------------------------------------------
To unsubscribe, e-mail: [EMAIL PROTECTED]
For additional commands, e-mail: [EMAIL PROTECTED]



      

---------------------------------------------------------------------
To unsubscribe, e-mail: [EMAIL PROTECTED]
For additional commands, e-mail: [EMAIL PROTECTED]



    
------------------------------------------------------------------------


sis0: flags=8802<BROADCAST,SIMPLEX,MULTICAST> mtu 1500
        options=8<VLAN_MTU>
        ether 00:0d:b9:06:5b:a0
        media: Ethernet autoselect (none)
        status: no carrier
sis1: flags=8843<UP,BROADCAST,RUNNING,SIMPLEX,MULTICAST> mtu 1500
        options=8<VLAN_MTU>
        inet 172.16.0.1 netmask 0xfffffe00 broadcast 172.16.1.255
        inet6 fe80::20d:b9ff:fe06:5ba1%sis1 prefixlen 64 scopeid 0x2
        ether 00:0d:b9:06:5b:a1
        media: Ethernet autoselect (100baseTX <full-duplex>)
        status: active
sis2: flags=8843<UP,BROADCAST,RUNNING,SIMPLEX,MULTICAST> mtu 1500
        options=8<VLAN_MTU>
        inet6 fe80::20d:b9ff:fe06:5ba2%sis2 prefixlen 64 scopeid 0x3
        ether 00:0d:b9:06:5b:a2
        media: Ethernet autoselect (none)
        status: no carrier
lo0: flags=8049<UP,LOOPBACK,RUNNING,MULTICAST> mtu 16384
        inet 127.0.0.1 netmask 0xff000000
        inet6 ::1 prefixlen 128
        inet6 fe80::1%lo0 prefixlen 64 scopeid 0x4
pfsync0: flags=41<UP,RUNNING> mtu 2020
        pfsync: syncdev: lo0 maxupd: 128
pflog0: flags=100<PROMISC> mtu 33208
ng0: flags=98d1<UP,POINTOPOINT,RUNNING,NOARP,SIMPLEX,LINK0,MULTICAST> mtu 1500
        inet 192.0.2.112 --> 192.0.2.113 netmask 0xffffffff
        inet6 fe80::20d:b9ff:fe06:5ba0%ng0 prefixlen 64 scopeid 0x7
tun0: flags=8051<UP,POINTOPOINT,RUNNING,MULTICAST> mtu 1500
        inet6 fe80::20d:b9ff:fe06:5ba0%tun0 prefixlen 64 scopeid 0x8
        inet 192.168.254.1 --> 192.168.254.2 netmask 0xffffffff
        Opened by PID 346
ng1: flags=8890<POINTOPOINT,NOARP,SIMPLEX,MULTICAST> mtu 1500
ng2: flags=8890<POINTOPOINT,NOARP,SIMPLEX,MULTICAST> mtu 1500
ng3: flags=8890<POINTOPOINT,NOARP,SIMPLEX,MULTICAST> mtu 1500
ng4: flags=8890<POINTOPOINT,NOARP,SIMPLEX,MULTICAST> mtu 1500
ng5: flags=8890<POINTOPOINT,NOARP,SIMPLEX,MULTICAST> mtu 1500
ng6: flags=8890<POINTOPOINT,NOARP,SIMPLEX,MULTICAST> mtu 1500
ng7: flags=8890<POINTOPOINT,NOARP,SIMPLEX,MULTICAST> mtu 1500
ng8: flags=8890<POINTOPOINT,NOARP,SIMPLEX,MULTICAST> mtu 1500
ng9: flags=8890<POINTOPOINT,NOARP,SIMPLEX,MULTICAST> mtu 1500
ng10: flags=8890<POINTOPOINT,NOARP,SIMPLEX,MULTICAST> mtu 1500
ng11: flags=8890<POINTOPOINT,NOARP,SIMPLEX,MULTICAST> mtu 1500
ng12: flags=8890<POINTOPOINT,NOARP,SIMPLEX,MULTICAST> mtu 1500
ng13: flags=8890<POINTOPOINT,NOARP,SIMPLEX,MULTICAST> mtu 1500
ng14: flags=8890<POINTOPOINT,NOARP,SIMPLEX,MULTICAST> mtu 1500
ng15: flags=8890<POINTOPOINT,NOARP,SIMPLEX,MULTICAST> mtu 1500
ng16: flags=8890<POINTOPOINT,NOARP,SIMPLEX,MULTICAST> mtu 1500

    
------------------------------------------------------------------------


Timecounter "i8254" frequency 1193182 Hz quality 0
CPU: Geode(TM) Integrated Processor by National Semi (233.32-MHz 586-class CPU)
  Origin = "Geode by NSC"  Id = 0x540  Stepping = 0
  Features=0x808131<FPU,TSC,MSR,CX8,CMOV,MMX>
real memory  = 134217728 (128 MB)
avail memory = 121917440 (116 MB)
wlan: mac acl policy registered
ath_hal: 0.9.16.16 (AR5210, AR5211, AR5212, RF5111, RF5112, RF2413, RF5413)
cpu0 on motherboard
pcib0: <Host to PCI bridge> pcibus 0 on motherboard
pci0: <PCI bus> on pcib0
pci0: <network> at device 13.0 (no driver attached)
sis0: <NatSemi DP8381[56] 10/100BaseTX> port 0x1000-0x10ff mem 
0x80040000-0x80040fff irq 10 at device 14.0 on pci0
sis0: Silicon Revision: DP83816A
miibus0: <MII bus> on sis0
ukphy0: <Generic IEEE 802.3u media interface> on miibus0
ukphy0:  10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
sis0: Ethernet address: 00:0d:b9:06:5b:a0
sis1: <NatSemi DP8381[56] 10/100BaseTX> port 0x1400-0x14ff mem 
0x80080000-0x80080fff irq 9 at device 15.0 on pci0
sis1: Silicon Revision: DP83816A
miibus1: <MII bus> on sis1
ukphy1: <Generic IEEE 802.3u media interface> on miibus1
ukphy1:  10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
sis1: Ethernet address: 00:0d:b9:06:5b:a1
sis2: <NatSemi DP8381[56] 10/100BaseTX> port 0x1800-0x18ff mem 
0x800c0000-0x800c0fff irq 11 at device 16.0 on pci0
sis2: Silicon Revision: DP83816A
miibus2: <MII bus> on sis2
ukphy2: <Generic IEEE 802.3u media interface> on miibus2
ukphy2:  10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
sis2: Ethernet address: 00:0d:b9:06:5b:a2
Geode GPIO@ = f400
Geode PC Engines WRAP.1C/1D/1E v1.tinyBIOS V1.4a (C)1997-2005
isab0: <PCI-ISA bridge> port 0xf400-0xf43f,0xf600-0xf63f at device 18.0 on pci0
isa0: <ISA bus> on isab0
pci0: <bridge> at device 18.1 (no driver attached)
atapci0: <National Geode SC1100 ATA33 controller> port 
0x1f0-0x1f7,0x3f6,0x170-0x177,0x376,0xfc00-0xfc0f at device 18.2 on pci0
ata0: <ATA channel 0> on atapci0
ata1: <ATA channel 1> on atapci0
pci0: <multimedia, audio> at device 18.3 (no driver attached)
Geode CBA@ 0x9000
Geode rev: 06 03
Timecounter "Geode" frequency 27000000 Hz quality 1000
pci0: <bridge> at device 18.5 (no driver attached)
orm0: <ISA Option ROM> at iomem 0xe0000-0xe7fff on isa0
ppc0: parallel port not found.
sio0 at port 0x3f8-0x3ff irq 4 flags 0x30 on isa0
sio0: type 16550A, console
sio1: configured irq 3 not in bitmap of probed irqs 0
sio1: port may not be enabled
RTC BIOS diagnostic error 80<clock_battery>
Timecounters tick every 10.000 msec
Fast IPsec: Initialized Security Association Processing.
ad0: 244MB <TOSHIBA THNCF256MQG 3.00> at ata0-master PIO4
GEOM_LABEL: Label for provider ad0a is ufs/pfSense.
GEOM_LABEL: Label for provider ad0d is ufs/pfSenseCfg.
Trying to mount root from ufs:/dev/ufs/pfSense
sis0: link state changed to DOWN
sis1: link state changed to DOWN
sis2: link state changed to DOWN
sis1: link state changed to UP
pflog0: promiscuous mode enabled


    
------------------------------------------------------------------------


---------------------------------------------------------------------
To unsubscribe, e-mail: [EMAIL PROTECTED]
For additional commands, e-mail: [EMAIL PROTECTED]



---------------------------------------------------------------------
To unsubscribe, e-mail: [EMAIL PROTECTED]
For additional commands, e-mail: [EMAIL PROTECTED]























					Reply via email to