On Sun, Mar 1, 2020 at 10:41 PM YASUOKA Masahiko <yasu...@openbsd.org> wrote:
>
> Hi,
>
> The problems you are pointing seem to be the same problem.
>
> > I'll try to test this diff next week if I can schedule some downtime.
>
> Test is appreciated.
>
> Also I'd like to know the result of
>
> hexdump -C /var/db/acpi/FACP.1
>
> when "Load Legacy Video Option ROM" setting is disabled.
I just tested a -current kernel built yesterday with that diff (your
post on Feb. 20), but unfortunately it does not fix the issue on my
hardware. As before, if "Load Legacy Video Option ROM" is disabled,
output is squished to a purple line and when devices are initialized,
vga1 is the wsdisplay0 device:
vga1 at pci7 dev 0 function 0 "Matrox MGA G200eR" rev 0x01
wsdisplay0 at vga1 mux 1: console (80x25, vt100 emulation)
wsdisplay0: screen 1-5 added (80x25, vt100 emulation)
efifb0 at mainbus0: 1280x1024, 32bpp
wsdisplay at efifb0 not configured
vs. with the legacy video ROM setting:
"Matrox MGA G200eR" rev 0x01 at pci7 dev 0 function 0 not configured
efifb0 at mainbus0: 1024x768, 32bpp
wsdisplay0 at efifb0 mux 1
wsdisplay0: screen 0-5 added (std, vt100 emulation)
I'm using a serial console, if it matters. Hmm... I just noticed that
with the legacy ROM setting disabled, both wsdisplay0 at vga1 mux
1/wskbd0 at ukbd0 *and* com1 claim to be the console. With the
setting enabled (and efifb working), only com1 is listed as console.
I haven't tried any of the later diffs as I'm not sure which are still
recommended.
The FACP.1 table does not change when the "Load Legacy Video Option
ROM" setting is changed. Here is its hexdump:
andrew@gsc-lb1:~/acpidump$ hexdump -C legacy-2.8.1/FACP.1
00000000 46 41 43 50 0c 01 00 00 05 62 44 45 4c 4c 20 20 |FACP.....bDELL |
00000010 50 45 5f 53 43 33 20 20 00 00 00 00 44 45 4c 4c |PE_SC3 ....DELL|
00000020 01 00 00 00 00 30 f8 8e 00 b0 fc 8e 00 04 09 00 |.....0..........|
00000030 b2 00 00 00 f0 f1 f2 00 00 18 00 00 00 00 00 00 |................|
00000040 04 18 00 00 00 00 00 00 50 18 00 00 08 18 00 00 |........P.......|
00000050 80 18 00 00 00 00 00 00 04 02 01 04 20 00 10 00 |............ ...|
00000060 65 00 e9 03 00 00 00 00 01 03 0d 00 32 11 00 00 |e...........2...|
00000070 a5 86 00 00 01 08 00 01 f9 0c 00 00 00 00 00 00 |................|
00000080 06 00 00 00 00 00 00 00 00 00 00 00 00 b0 fc 8e |................|
00000090 00 00 00 00 01 20 00 02 00 18 00 00 00 00 00 00 |..... ..........|
000000a0 01 00 00 02 00 00 00 00 00 00 00 00 01 10 00 02 |................|
000000b0 04 18 00 00 00 00 00 00 01 00 00 02 00 00 00 00 |................|
000000c0 00 00 00 00 01 08 00 01 50 18 00 00 00 00 00 00 |........P.......|
000000d0 01 20 00 03 08 18 00 00 00 00 00 00 01 00 00 01 |. ..............|
000000e0 80 18 00 00 00 00 00 00 01 00 00 01 00 00 00 00 |................|
000000f0 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 |................|
00000100 00 00 00 00 00 00 00 00 00 00 00 00 |............|
0000010c
The only ACPI change made by toggling that option is the DMAR.25
table. Here are both versions:
Legacy Video ROM enabled:
00000000 44 4d 41 52 90 00 00 00 01 83 49 4e 54 45 4c 20 |DMAR......INTEL |
00000010 47 4e 4c 52 00 00 00 00 01 00 00 00 49 4e 54 4c |GNLR........INTL|
00000020 01 00 00 00 26 01 00 00 00 00 00 00 00 00 00 00 |....&...........|
00000030 00 00 20 00 01 00 00 00 00 00 d9 fe 00 00 00 00 |.. .............|
00000040 03 08 00 00 02 f0 1f 00 04 08 00 00 00 00 1f 00 |................|
00000050 01 00 20 00 00 00 00 00 00 b0 ba 7c 00 00 00 00 |.. ........|....|
00000060 ff 2f bb 84 00 00 00 00 01 08 00 00 00 01 00 00 |./..............|
00000070 01 00 20 00 00 00 00 00 00 10 31 8e 00 00 00 00 |.. .......1.....|
00000080 ff 0f 33 8e 00 00 00 00 01 08 00 00 00 00 14 00 |..3.............|
00000090
and disabled:
00000000 44 4d 41 52 90 00 00 00 01 05 49 4e 54 45 4c 20 |DMAR......INTEL |
00000010 47 4e 4c 52 00 00 00 00 01 00 00 00 49 4e 54 4c |GNLR........INTL|
00000020 01 00 00 00 26 01 00 00 00 00 00 00 00 00 00 00 |....&...........|
00000030 00 00 20 00 01 00 00 00 00 00 d9 fe 00 00 00 00 |.. .............|
00000040 03 08 00 00 02 f0 1f 00 04 08 00 00 00 00 1f 00 |................|
00000050 01 00 20 00 00 00 00 00 00 c0 e9 7c 00 00 00 00 |.. ........|....|
00000060 ff 3f ea 84 00 00 00 00 01 08 00 00 00 01 00 00 |.?..............|
00000070 01 00 20 00 00 00 00 00 00 10 31 8e 00 00 00 00 |.. .......1.....|
00000080 ff 0f 33 8e 00 00 00 00 01 08 00 00 00 00 14 00 |..3.............|
00000090
I've attached full dmesgs for both legacy video ROM enabled and
disabled. The system is currently on 6.5, but the
efifb/wsdisplay/etc. messages are the same in -current. Thanks for
trying to figure this out!
-Andrew
OpenBSD 6.5 (GENERIC.MP) #8: Tue Jan 14 23:16:33 MST 2020
t...@syspatch-65-amd64.openbsd.org:/usr/src/sys/arch/amd64/compile/GENERIC.MP
real mem = 8394772480 (8005MB)
avail mem = 8130699264 (7754MB)
mpath0 at root
scsibus0 at mpath0: 256 targets
mainbus0 at root
bios0 at mainbus0: SMBIOS rev. 2.8 @ 0x8ef68000 (43 entries)
bios0: vendor Dell Inc. version "2.8.1" date 11/05/2019
bios0: Dell Inc. PowerEdge R230
acpi0 at bios0: rev 2
acpi0: sleep states S0 S5
acpi0: tables DSDT FACP BOOT SSDT SLIC HPET LPIT APIC MCFG WDAT SSDT DBGP DBG2
SSDT SSDT SSDT SSDT SSDT SSDT PRAD HEST BERT ERST EINJ DMAR FPDT SPCR
acpi0: wakeup devices PEGP(S0) PEG0(S0) PEGP(S0) PEG1(S0) PEGP(S0) PEG2(S0)
XHC_(S0) XDCI(S0) PXSX(S0) RP01(S0) PXSX(S0) RP02(S0) PXSX(S0) RP03(S0)
PXSX(S0) RP04(S0) [...]
acpitimer0 at acpi0: 3579545 Hz, 24 bits
acpihpet0 at acpi0: 23999999 Hz
acpimadt0 at acpi0 addr 0xfee00000: PC-AT compat
cpu0 at mainbus0: apid 0 (boot processor)
cpu0: Intel(R) Core(TM) i3-6100 CPU @ 3.70GHz, 3692.77 MHz, 06-5e-03
cpu0:
FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,CFLUSH,DS,ACPI,MMX,FXSR,SSE,SSE2,SS,HTT,TM,PBE,SSE3,PCLMUL,DTES64,MWAIT,DS-CPL,VMX,EST,TM2,SSSE3,SDBG,FMA3,CX16,xTPR,PDCM,PCID,SSE4.1,SSE4.2,x2APIC,MOVBE,POPCNT,DEADLINE,AES,XSAVE,AVX,F16C,RDRAND,NXE,PAGE1GB,RDTSCP,LONG,LAHF,ABM,3DNOWP,PERF,ITSC,FSGSBASE,SGX,BMI1,AVX2,SMEP,BMI2,ERMS,INVPCID,MPX,RDSEED,ADX,SMAP,CLFLUSHOPT,PT,MD_CLEAR,TSXFA,IBRS,IBPB,STIBP,L1DF,SSBD,SENSOR,ARAT,XSAVEOPT,XSAVEC,XGETBV1,XSAVES,MELTDOWN
cpu0: 256KB 64b/line 8-way L2 cache
cpu0: smt 0, core 0, package 0
mtrr: Pentium Pro MTRR support, 10 var ranges, 88 fixed ranges
cpu0: apic clock running at 24MHz
cpu0: mwait min=64, max=64, C-substates=0.2.1.2.4.1, IBE
cpu1 at mainbus0: apid 2 (application processor)
cpu1: Intel(R) Core(TM) i3-6100 CPU @ 3.70GHz, 3691.42 MHz, 06-5e-03
cpu1:
FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,CFLUSH,DS,ACPI,MMX,FXSR,SSE,SSE2,SS,HTT,TM,PBE,SSE3,PCLMUL,DTES64,MWAIT,DS-CPL,VMX,EST,TM2,SSSE3,SDBG,FMA3,CX16,xTPR,PDCM,PCID,SSE4.1,SSE4.2,x2APIC,MOVBE,POPCNT,DEADLINE,AES,XSAVE,AVX,F16C,RDRAND,NXE,PAGE1GB,RDTSCP,LONG,LAHF,ABM,3DNOWP,PERF,ITSC,FSGSBASE,SGX,BMI1,AVX2,SMEP,BMI2,ERMS,INVPCID,MPX,RDSEED,ADX,SMAP,CLFLUSHOPT,PT,MD_CLEAR,TSXFA,IBRS,IBPB,STIBP,L1DF,SSBD,SENSOR,ARAT,XSAVEOPT,XSAVEC,XGETBV1,XSAVES,MELTDOWN
cpu1: 256KB 64b/line 8-way L2 cache
cpu1: smt 0, core 1, package 0
cpu2 at mainbus0: apid 1 (application processor)
cpu2: Intel(R) Core(TM) i3-6100 CPU @ 3.70GHz, 3691.41 MHz, 06-5e-03
cpu2:
FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,CFLUSH,DS,ACPI,MMX,FXSR,SSE,SSE2,SS,HTT,TM,PBE,SSE3,PCLMUL,DTES64,MWAIT,DS-CPL,VMX,EST,TM2,SSSE3,SDBG,FMA3,CX16,xTPR,PDCM,PCID,SSE4.1,SSE4.2,x2APIC,MOVBE,POPCNT,DEADLINE,AES,XSAVE,AVX,F16C,RDRAND,NXE,PAGE1GB,RDTSCP,LONG,LAHF,ABM,3DNOWP,PERF,ITSC,FSGSBASE,SGX,BMI1,AVX2,SMEP,BMI2,ERMS,INVPCID,MPX,RDSEED,ADX,SMAP,CLFLUSHOPT,PT,MD_CLEAR,TSXFA,IBRS,IBPB,STIBP,L1DF,SSBD,SENSOR,ARAT,XSAVEOPT,XSAVEC,XGETBV1,XSAVES,MELTDOWN
cpu2: 256KB 64b/line 8-way L2 cache
cpu2: smt 1, core 0, package 0
cpu3 at mainbus0: apid 3 (application processor)
cpu3: Intel(R) Core(TM) i3-6100 CPU @ 3.70GHz, 3691.42 MHz, 06-5e-03
cpu3:
FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,CFLUSH,DS,ACPI,MMX,FXSR,SSE,SSE2,SS,HTT,TM,PBE,SSE3,PCLMUL,DTES64,MWAIT,DS-CPL,VMX,EST,TM2,SSSE3,SDBG,FMA3,CX16,xTPR,PDCM,PCID,SSE4.1,SSE4.2,x2APIC,MOVBE,POPCNT,DEADLINE,AES,XSAVE,AVX,F16C,RDRAND,NXE,PAGE1GB,RDTSCP,LONG,LAHF,ABM,3DNOWP,PERF,ITSC,FSGSBASE,SGX,BMI1,AVX2,SMEP,BMI2,ERMS,INVPCID,MPX,RDSEED,ADX,SMAP,CLFLUSHOPT,PT,MD_CLEAR,TSXFA,IBRS,IBPB,STIBP,L1DF,SSBD,SENSOR,ARAT,XSAVEOPT,XSAVEC,XGETBV1,XSAVES,MELTDOWN
cpu3: 256KB 64b/line 8-way L2 cache
cpu3: smt 1, core 1, package 0
ioapic0 at mainbus0: apid 2 pa 0xfec00000, version 20, 24 pins
acpimcfg0 at acpi0
acpimcfg0: addr 0xe0000000, bus 0-255
acpiprt0 at acpi0: bus 0 (PCI0)
acpiprt0: no apic found for irq 32
acpiprt0: no apic found for irq 33
acpiprt0: no apic found for irq 34
acpiprt1 at acpi0: bus 1 (PEG0)
acpiprt2 at acpi0: bus 2 (PEG1)
acpiprt3 at acpi0: bus -1 (PEG2)
acpiprt4 at acpi0: bus -1 (RP01)
acpiprt5 at acpi0: bus -1 (RP02)
acpiprt6 at acpi0: bus -1 (RP03)
acpiprt7 at acpi0: bus -1 (RP04)
acpiprt8 at acpi0: bus -1 (RP05)
acpiprt9 at acpi0: bus -1 (RP06)
acpiprt10 at acpi0: bus -1 (RP07)
acpiprt11 at acpi0: bus -1 (RP08)
acpiprt12 at acpi0: bus 3 (RP09)
acpiprt13 at acpi0: bus -1 (RP10)
acpiprt14 at acpi0: bus 4 (RP11)
acpiprt15 at acpi0: bus -1 (RP12)
acpiprt16 at acpi0: bus -1 (RP13)
acpiprt17 at acpi0: bus -1 (RP14)
acpiprt18 at acpi0: bus -1 (RP15)
acpiprt19 at acpi0: bus -1 (RP16)
acpiprt20 at acpi0: bus -1 (RP17)
acpiprt21 at acpi0: bus -1 (RP18)
acpiprt22 at acpi0: bus -1 (RP19)
acpiprt23 at acpi0: bus -1 (RP20)
acpicpu0 at acpi0: C3(500@76 mwait.1@0x10), C1(1000@1 mwait.1), PSS
acpicpu1 at acpi0: C3(500@76 mwait.1@0x10), C1(1000@1 mwait.1), PSS
acpicpu2 at acpi0: C3(500@76 mwait.1@0x10), C1(1000@1 mwait.1), PSS
acpicpu3 at acpi0: C3(500@76 mwait.1@0x10), C1(1000@1 mwait.1), PSS
acpipci0 at acpi0 PCI0: 0x00000000 0x00000011 0x00000001
acpicmos0 at acpi0
acpibtn0 at acpi0: SLPB
"PNP0C14" at acpi0 not configured
"PNP0C33" at acpi0 not configured
acpivideo0 at acpi0: GFX0
acpivout0 at acpivideo0: DD1F
ipmi at mainbus0 not configured
cpu0: using VERW MDS workaround
cpu0: Enhanced SpeedStep 3692 MHz: speeds: 3700, 3500, 3300, 3100, 2900, 2700,
2500, 2300, 2200, 2000, 1800, 1600, 1400, 1200, 1000, 800 MHz
pci0 at mainbus0 bus 0
pchb0 at pci0 dev 0 function 0 "Intel Core 6G Host" rev 0x07
ppb0 at pci0 dev 1 function 0 "Intel Core 6G PCIE" rev 0x07: msi
pci1 at ppb0 bus 1
mfii0 at pci1 dev 0 function 0 "Symbios Logic MegaRAID SAS3008" rev 0x02: msi
mfii0: "PERC H330 Adapter", firmware 25.5.6.0009
scsibus1 at mfii0: 32 targets
sd0 at scsibus1 targ 0 lun 0: <DELL, PERC H330 Adp, 4.30> SCSI3 0/direct fixed
naa.61418770565c00001e463dcfcef6bd7b
sd0: 476416MB, 512 bytes/sector, 975699968 sectors
scsibus2 at mfii0: 256 targets
ppb1 at pci0 dev 1 function 1 "Intel Core 6G PCIE" rev 0x07: msi
pci2 at ppb1 bus 2
xhci0 at pci0 dev 20 function 0 "Intel 100 Series xHCI" rev 0x31: msi, xHCI 1.0
usb0 at xhci0: USB revision 3.0
uhub0 at usb0 configuration 1 interface 0 "Intel xHCI root hub" rev 3.00/1.00
addr 1
pchtemp0 at pci0 dev 20 function 2 "Intel 100 Series Thermal" rev 0x31
"Intel 100 Series MEI" rev 0x31 at pci0 dev 22 function 0 not configured
"Intel 100 Series MEI" rev 0x31 at pci0 dev 22 function 1 not configured
ahci0 at pci0 dev 23 function 0 "Intel 100 Series AHCI" rev 0x31: msi, AHCI
1.3.1
ahci0: port 4: 1.5Gb/s
scsibus3 at ahci0: 32 targets
cd0 at scsibus3 targ 4 lun 0: <HL-DT-ST, DVD-ROM DU90N, D3B0> ATAPI 5/cdrom
removable
ppb2 at pci0 dev 29 function 0 "Intel 100 Series PCIE" rev 0xf1: msi
pci3 at ppb2 bus 3
3:0:0: mem address conflict 0xfffc0000/0x40000
3:0:1: mem address conflict 0xfffc0000/0x40000
bge0 at pci3 dev 0 function 0 "Broadcom BCM5720" rev 0x00, BCM5720 A0
(0x5720000), APE firmware NCSI 1.5.12.0: msi, address 34:17:eb:eb:31:5e
brgphy0 at bge0 phy 1: BCM5720C 10/100/1000baseT PHY, rev. 0
bge1 at pci3 dev 0 function 1 "Broadcom BCM5720" rev 0x00, BCM5720 A0
(0x5720000), APE firmware NCSI 1.5.12.0: msi, address 34:17:eb:eb:31:5f
brgphy1 at bge1 phy 2: BCM5720C 10/100/1000baseT PHY, rev. 0
ppb3 at pci0 dev 29 function 2 "Intel 100 Series PCIE" rev 0xf1: msi
pci4 at ppb3 bus 4
ppb4 at pci4 dev 0 function 0 "Renesas SH7758 PCIE Switch" rev 0x00
pci5 at ppb4 bus 5
ppb5 at pci5 dev 0 function 0 "Renesas SH7758 PCIE Switch" rev 0x00
pci6 at ppb5 bus 6
ppb6 at pci6 dev 0 function 0 "Renesas SH7758 PCIE-PCI" rev 0x00
pci7 at ppb6 bus 7
"Matrox MGA G200eR" rev 0x01 at pci7 dev 0 function 0 not configured
pcib0 at pci0 dev 31 function 0 "Intel C236 LPC" rev 0x31
"Intel 100 Series PMC" rev 0x31 at pci0 dev 31 function 2 not configured
ichiic0 at pci0 dev 31 function 4 "Intel 100 Series SMBus" rev 0x31: apic 2 int
16
iic0 at ichiic0
sdtemp0 at iic0 addr 0x19: at30tse004
sdtemp1 at iic0 addr 0x1b: at30tse004
isa0 at pcib0
isadma0 at isa0
com0 at isa0 port 0x3f8/8 irq 4: ns16550a, 16 byte fifo
com1 at isa0 port 0x2f8/8 irq 3: ns16550a, 16 byte fifo
com1: console
pcppi0 at isa0 port 0x61
spkr0 at pcppi0
vmm0 at mainbus0: VMX/EPT
efifb0 at mainbus0: 1024x768, 32bpp
wsdisplay0 at efifb0 mux 1
wsdisplay0: screen 0-5 added (std, vt100 emulation)
uhub0: port 2, set config 0 at addr 2 failed
uhub0: device problem, disabling port 2
uhub1 at uhub0 port 3 configuration 1 interface 0 "no manufacturer Gadget USB
HUB" rev 2.00/0.00 addr 2
vscsi0 at root
scsibus4 at vscsi0: 256 targets
softraid0 at root
scsibus5 at softraid0: 256 targets
root on sd0a (264382cab5a10a3c.a) swap on sd0b dump on sd0b
carp1: state transition: BACKUP -> MASTER
carp0: state transition: BACKUP -> MASTER
uhidev0 at uhub0 port 2 configuration 1 interface 0 "Avocent APC AP5631" rev
1.10/1.00 addr 3
uhidev0: iclass 3/1
ukbd0 at uhidev0: 8 variable keys, 6 key codes, country code 33
wskbd0 at ukbd0 mux 1
wskbd0: connecting to wsdisplay0
uhidev1 at uhub0 port 2 configuration 1 interface 1 "Avocent APC AP5631" rev
1.10/1.00 addr 3
uhidev1: iclass 3/1, 3 report ids
ums0 at uhidev1 reportid 1: 5 buttons, Z dir
wsmouse0 at ums0 mux 0
uhid0 at uhidev1 reportid 2: input=2, output=0, feature=0
uhid1 at uhidev1 reportid 3: input=1, output=0, feature=0
OpenBSD 6.5 (GENERIC.MP) #8: Tue Jan 14 23:16:33 MST 2020
t...@syspatch-65-amd64.openbsd.org:/usr/src/sys/arch/amd64/compile/GENERIC.MP
real mem = 8394772480 (8005MB)
avail mem = 8130707456 (7754MB)
mpath0 at root
scsibus0 at mpath0: 256 targets
mainbus0 at root
bios0 at mainbus0: SMBIOS rev. 2.8 @ 0x8ef68000 (43 entries)
bios0: vendor Dell Inc. version "2.8.1" date 11/05/2019
bios0: Dell Inc. PowerEdge R230
acpi0 at bios0: rev 2
acpi0: sleep states S0 S5
acpi0: tables DSDT FACP BOOT SSDT SLIC HPET LPIT APIC MCFG WDAT SSDT DBGP DBG2
SSDT SSDT SSDT SSDT SSDT SSDT PRAD HEST BERT ERST EINJ DMAR FPDT SPCR
acpi0: wakeup devices PEGP(S0) PEG0(S0) PEGP(S0) PEG1(S0) PEGP(S0) PEG2(S0)
XHC_(S0) XDCI(S0) PXSX(S0) RP01(S0) PXSX(S0) RP02(S0) PXSX(S0) RP03(S0)
PXSX(S0) RP04(S0) [...]
acpitimer0 at acpi0: 3579545 Hz, 24 bits
acpihpet0 at acpi0: 23999999 Hz
acpimadt0 at acpi0 addr 0xfee00000: PC-AT compat
cpu0 at mainbus0: apid 0 (boot processor)
cpu0: Intel(R) Core(TM) i3-6100 CPU @ 3.70GHz, 3692.76 MHz, 06-5e-03
cpu0:
FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,CFLUSH,DS,ACPI,MMX,FXSR,SSE,SSE2,SS,HTT,TM,PBE,SSE3,PCLMUL,DTES64,MWAIT,DS-CPL,VMX,EST,TM2,SSSE3,SDBG,FMA3,CX16,xTPR,PDCM,PCID,SSE4.1,SSE4.2,x2APIC,MOVBE,POPCNT,DEADLINE,AES,XSAVE,AVX,F16C,RDRAND,NXE,PAGE1GB,RDTSCP,LONG,LAHF,ABM,3DNOWP,PERF,ITSC,FSGSBASE,SGX,BMI1,AVX2,SMEP,BMI2,ERMS,INVPCID,MPX,RDSEED,ADX,SMAP,CLFLUSHOPT,PT,MD_CLEAR,TSXFA,IBRS,IBPB,STIBP,L1DF,SSBD,SENSOR,ARAT,XSAVEOPT,XSAVEC,XGETBV1,XSAVES,MELTDOWN
cpu0: 256KB 64b/line 8-way L2 cache
cpu0: smt 0, core 0, package 0
mtrr: Pentium Pro MTRR support, 10 var ranges, 88 fixed ranges
cpu0: apic clock running at 24MHz
cpu0: mwait min=64, max=64, C-substates=0.2.1.2.4.1, IBE
cpu1 at mainbus0: apid 2 (application processor)
cpu1: Intel(R) Core(TM) i3-6100 CPU @ 3.70GHz, 3691.41 MHz, 06-5e-03
cpu1:
FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,CFLUSH,DS,ACPI,MMX,FXSR,SSE,SSE2,SS,HTT,TM,PBE,SSE3,PCLMUL,DTES64,MWAIT,DS-CPL,VMX,EST,TM2,SSSE3,SDBG,FMA3,CX16,xTPR,PDCM,PCID,SSE4.1,SSE4.2,x2APIC,MOVBE,POPCNT,DEADLINE,AES,XSAVE,AVX,F16C,RDRAND,NXE,PAGE1GB,RDTSCP,LONG,LAHF,ABM,3DNOWP,PERF,ITSC,FSGSBASE,SGX,BMI1,AVX2,SMEP,BMI2,ERMS,INVPCID,MPX,RDSEED,ADX,SMAP,CLFLUSHOPT,PT,MD_CLEAR,TSXFA,IBRS,IBPB,STIBP,L1DF,SSBD,SENSOR,ARAT,XSAVEOPT,XSAVEC,XGETBV1,XSAVES,MELTDOWN
cpu1: 256KB 64b/line 8-way L2 cache
cpu1: smt 0, core 1, package 0
cpu2 at mainbus0: apid 1 (application processor)
cpu2: Intel(R) Core(TM) i3-6100 CPU @ 3.70GHz, 3691.41 MHz, 06-5e-03
cpu2:
FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,CFLUSH,DS,ACPI,MMX,FXSR,SSE,SSE2,SS,HTT,TM,PBE,SSE3,PCLMUL,DTES64,MWAIT,DS-CPL,VMX,EST,TM2,SSSE3,SDBG,FMA3,CX16,xTPR,PDCM,PCID,SSE4.1,SSE4.2,x2APIC,MOVBE,POPCNT,DEADLINE,AES,XSAVE,AVX,F16C,RDRAND,NXE,PAGE1GB,RDTSCP,LONG,LAHF,ABM,3DNOWP,PERF,ITSC,FSGSBASE,SGX,BMI1,AVX2,SMEP,BMI2,ERMS,INVPCID,MPX,RDSEED,ADX,SMAP,CLFLUSHOPT,PT,MD_CLEAR,TSXFA,IBRS,IBPB,STIBP,L1DF,SSBD,SENSOR,ARAT,XSAVEOPT,XSAVEC,XGETBV1,XSAVES,MELTDOWN
cpu2: 256KB 64b/line 8-way L2 cache
cpu2: smt 1, core 0, package 0
cpu3 at mainbus0: apid 3 (application processor)
cpu3: Intel(R) Core(TM) i3-6100 CPU @ 3.70GHz, 3691.41 MHz, 06-5e-03
cpu3:
FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,CFLUSH,DS,ACPI,MMX,FXSR,SSE,SSE2,SS,HTT,TM,PBE,SSE3,PCLMUL,DTES64,MWAIT,DS-CPL,VMX,EST,TM2,SSSE3,SDBG,FMA3,CX16,xTPR,PDCM,PCID,SSE4.1,SSE4.2,x2APIC,MOVBE,POPCNT,DEADLINE,AES,XSAVE,AVX,F16C,RDRAND,NXE,PAGE1GB,RDTSCP,LONG,LAHF,ABM,3DNOWP,PERF,ITSC,FSGSBASE,SGX,BMI1,AVX2,SMEP,BMI2,ERMS,INVPCID,MPX,RDSEED,ADX,SMAP,CLFLUSHOPT,PT,MD_CLEAR,TSXFA,IBRS,IBPB,STIBP,L1DF,SSBD,SENSOR,ARAT,XSAVEOPT,XSAVEC,XGETBV1,XSAVES,MELTDOWN
cpu3: 256KB 64b/line 8-way L2 cache
cpu3: smt 1, core 1, package 0
ioapic0 at mainbus0: apid 2 pa 0xfec00000, version 20, 24 pins
acpimcfg0 at acpi0
acpimcfg0: addr 0xe0000000, bus 0-255
acpiprt0 at acpi0: bus 0 (PCI0)
acpiprt0: no apic found for irq 32
acpiprt0: no apic found for irq 33
acpiprt0: no apic found for irq 34
acpiprt1 at acpi0: bus 1 (PEG0)
acpiprt2 at acpi0: bus 2 (PEG1)
acpiprt3 at acpi0: bus -1 (PEG2)
acpiprt4 at acpi0: bus -1 (RP01)
acpiprt5 at acpi0: bus -1 (RP02)
acpiprt6 at acpi0: bus -1 (RP03)
acpiprt7 at acpi0: bus -1 (RP04)
acpiprt8 at acpi0: bus -1 (RP05)
acpiprt9 at acpi0: bus -1 (RP06)
acpiprt10 at acpi0: bus -1 (RP07)
acpiprt11 at acpi0: bus -1 (RP08)
acpiprt12 at acpi0: bus 3 (RP09)
acpiprt13 at acpi0: bus -1 (RP10)
acpiprt14 at acpi0: bus 4 (RP11)
acpiprt15 at acpi0: bus -1 (RP12)
acpiprt16 at acpi0: bus -1 (RP13)
acpiprt17 at acpi0: bus -1 (RP14)
acpiprt18 at acpi0: bus -1 (RP15)
acpiprt19 at acpi0: bus -1 (RP16)
acpiprt20 at acpi0: bus -1 (RP17)
acpiprt21 at acpi0: bus -1 (RP18)
acpiprt22 at acpi0: bus -1 (RP19)
acpiprt23 at acpi0: bus -1 (RP20)
acpicpu0 at acpi0: C3(500@76 mwait.1@0x10), C1(1000@1 mwait.1), PSS
acpicpu1 at acpi0: C3(500@76 mwait.1@0x10), C1(1000@1 mwait.1), PSS
acpicpu2 at acpi0: C3(500@76 mwait.1@0x10), C1(1000@1 mwait.1), PSS
acpicpu3 at acpi0: C3(500@76 mwait.1@0x10), C1(1000@1 mwait.1), PSS
acpipci0 at acpi0 PCI0: 0x00000000 0x00000011 0x00000001
acpicmos0 at acpi0
acpibtn0 at acpi0: SLPB
"PNP0C14" at acpi0 not configured
"PNP0C33" at acpi0 not configured
acpivideo0 at acpi0: GFX0
acpivout0 at acpivideo0: DD1F
ipmi at mainbus0 not configured
cpu0: using VERW MDS workaround
cpu0: Enhanced SpeedStep 3692 MHz: speeds: 3700, 3500, 3300, 3100, 2900, 2700,
2500, 2300, 2200, 2000, 1800, 1600, 1400, 1200, 1000, 800 MHz
pci0 at mainbus0 bus 0
pchb0 at pci0 dev 0 function 0 "Intel Core 6G Host" rev 0x07
ppb0 at pci0 dev 1 function 0 "Intel Core 6G PCIE" rev 0x07: msi
pci1 at ppb0 bus 1
mfii0 at pci1 dev 0 function 0 "Symbios Logic MegaRAID SAS3008" rev 0x02: msi
mfii0: "PERC H330 Adapter", firmware 25.5.6.0009
scsibus1 at mfii0: 32 targets
sd0 at scsibus1 targ 0 lun 0: <DELL, PERC H330 Adp, 4.30> SCSI3 0/direct fixed
naa.61418770565c00001e463dcfcef6bd7b
sd0: 476416MB, 512 bytes/sector, 975699968 sectors
scsibus2 at mfii0: 256 targets
ppb1 at pci0 dev 1 function 1 "Intel Core 6G PCIE" rev 0x07: msi
pci2 at ppb1 bus 2
xhci0 at pci0 dev 20 function 0 "Intel 100 Series xHCI" rev 0x31: msi, xHCI 1.0
usb0 at xhci0: USB revision 3.0
uhub0 at usb0 configuration 1 interface 0 "Intel xHCI root hub" rev 3.00/1.00
addr 1
pchtemp0 at pci0 dev 20 function 2 "Intel 100 Series Thermal" rev 0x31
"Intel 100 Series MEI" rev 0x31 at pci0 dev 22 function 0 not configured
"Intel 100 Series MEI" rev 0x31 at pci0 dev 22 function 1 not configured
ahci0 at pci0 dev 23 function 0 "Intel 100 Series AHCI" rev 0x31: msi, AHCI
1.3.1
ahci0: port 4: 1.5Gb/s
scsibus3 at ahci0: 32 targets
cd0 at scsibus3 targ 4 lun 0: <HL-DT-ST, DVD-ROM DU90N, D3B0> ATAPI 5/cdrom
removable
ppb2 at pci0 dev 29 function 0 "Intel 100 Series PCIE" rev 0xf1: msi
pci3 at ppb2 bus 3
3:0:0: mem address conflict 0xfffc0000/0x40000
3:0:1: mem address conflict 0xfffc0000/0x40000
bge0 at pci3 dev 0 function 0 "Broadcom BCM5720" rev 0x00, BCM5720 A0
(0x5720000), APE firmware NCSI 1.5.12.0: msi, address 34:17:eb:eb:31:5e
brgphy0 at bge0 phy 1: BCM5720C 10/100/1000baseT PHY, rev. 0
bge1 at pci3 dev 0 function 1 "Broadcom BCM5720" rev 0x00, BCM5720 A0
(0x5720000), APE firmware NCSI 1.5.12.0: msi, address 34:17:eb:eb:31:5f
brgphy1 at bge1 phy 2: BCM5720C 10/100/1000baseT PHY, rev. 0
ppb3 at pci0 dev 29 function 2 "Intel 100 Series PCIE" rev 0xf1: msi
pci4 at ppb3 bus 4
ppb4 at pci4 dev 0 function 0 "Renesas SH7758 PCIE Switch" rev 0x00
pci5 at ppb4 bus 5
ppb5 at pci5 dev 0 function 0 "Renesas SH7758 PCIE Switch" rev 0x00
pci6 at ppb5 bus 6
ppb6 at pci6 dev 0 function 0 "Renesas SH7758 PCIE-PCI" rev 0x00
pci7 at ppb6 bus 7
vga1 at pci7 dev 0 function 0 "Matrox MGA G200eR" rev 0x01
wsdisplay0 at vga1 mux 1: console (80x25, vt100 emulation)
wsdisplay0: screen 1-5 added (80x25, vt100 emulation)
pcib0 at pci0 dev 31 function 0 "Intel C236 LPC" rev 0x31
"Intel 100 Series PMC" rev 0x31 at pci0 dev 31 function 2 not configured
ichiic0 at pci0 dev 31 function 4 "Intel 100 Series SMBus" rev 0x31: apic 2 int
16
iic0 at ichiic0
sdtemp0 at iic0 addr 0x19: at30tse004
sdtemp1 at iic0 addr 0x1b: at30tse004
isa0 at pcib0
isadma0 at isa0
com0 at isa0 port 0x3f8/8 irq 4: ns16550a, 16 byte fifo
com1 at isa0 port 0x2f8/8 irq 3: ns16550a, 16 byte fifo
com1: console
pcppi0 at isa0 port 0x61
spkr0 at pcppi0
vmm0 at mainbus0: VMX/EPT
efifb0 at mainbus0: 1280x1024, 32bpp
wsdisplay at efifb0 not configured
uhidev0 at uhub0 port 2 configuration 1 interface 0 "Avocent APC AP5631" rev
1.10/1.00 addr 2
uhidev0: iclass 3/1
ukbd0 at uhidev0: 8 variable keys, 6 key codes, country code 33
wskbd0 at ukbd0: console keyboard, using wsdisplay0
uhidev1 at uhub0 port 2 configuration 1 interface 1 "Avocent APC AP5631" rev
1.10/1.00 addr 2
uhidev1: iclass 3/1, 3 report ids
ums0 at uhidev1 reportid 1: 5 buttons, Z dir
wsmouse0 at ums0 mux 0
uhid0 at uhidev1 reportid 2: input=2, output=0, feature=0
uhid1 at uhidev1 reportid 3: input=1, output=0, feature=0
uhub1 at uhub0 port 3 configuration 1 interface 0 "no manufacturer Gadget USB
HUB" rev 2.00/0.00 addr 3
vscsi0 at root
scsibus4 at vscsi0: 256 targets
softraid0 at root
scsibus5 at softraid0: 256 targets
root on sd0a (264382cab5a10a3c.a) swap on sd0b dump on sd0b
WARNING: / was not properly unmounted
carp0: state transition: BACKUP -> MASTER
carp1: state transition: BACKUP -> MASTER
