On Sun, Feb 27, 2022 at 06:19:02AM +0000, Visa Hankala wrote:
> On Sat, Feb 26, 2022 at 08:40:25AM +0100, Anton Lindqvist wrote:
> > Hi,
> > This enables fifo support in pluart(4). While here, I changed the
> > attachment output to look more like com(4). Tested on my rpi3b which has
> > a 16 byte fifo.
> >
> > Comments? OK?
> >
> > diff --git sys/dev/ic/pluart.c sys/dev/ic/pluart.c
> > index eaa11b6c44b..601435c0e0c 100644
> > --- sys/dev/ic/pluart.c
> > +++ sys/dev/ic/pluart.c
> > @@ -99,6 +99,13 @@
> > #define UART_CR_CTSE (1 << 14) /* CTS hardware flow
> > control enable */
> > #define UART_CR_RTSE (1 << 15) /* RTS hardware flow
> > control enable */
> > #define UART_IFLS 0x34 /* Interrupt FIFO level select
> > register */
> > +#define UART_IFLS_RX_SHIFT 3 /* RX level in bits [5:3] */
> > +#define UART_IFLS_TX_SHIFT 0 /* TX level in bits [2:0] */
> > +#define UART_IFLS_1_8 0 /* FIFO 1/8 full */
> > +#define UART_IFLS_1_4 1 /* FIFO 1/4 full */
> > +#define UART_IFLS_1_2 2 /* FIFO 1/2 full */
> > +#define UART_IFLS_3_4 3 /* FIFO 3/4 full */
> > +#define UART_IFLS_7_8 4 /* FIFO 7/8 full */
> > #define UART_IMSC 0x38 /* Interrupt mask set/clear
> > register */
> > #define UART_IMSC_RIMIM (1 << 0)
> > #define UART_IMSC_CTSMIM (1 << 1)
> > @@ -115,6 +122,11 @@
> > #define UART_MIS 0x40 /* Masked interrupt status
> > register */
> > #define UART_ICR 0x44 /* Interrupt clear register */
> > #define UART_DMACR 0x48 /* DMA control register */
> > +#define UART_PID0 0xfe0 /* Peripheral identification
> > register 0 */
> > +#define UART_PID1 0xfe4 /* Peripheral identification
> > register 1 */
> > +#define UART_PID2 0xfe8 /* Peripheral identification
> > register 2 */
> > +#define UART_PID2_REV(x) ((x) >> 4)
>
> The revision field covers bits 7:4. Should other bits be masked out?
> PL011 r1p5 documentation says that bits 15:8 must read as zeroes, but
> that does not necessarily tell what possible future revisions will do.
I trusted the bits of the documentation you referred to but lets play it
safe.
>
> > +#define UART_PID3 0xfec /* Peripheral identification
> > register 3 */
> > #define UART_SPACE 0x100
> >
> > void pluartcnprobe(struct consdev *cp);
> > @@ -150,7 +162,12 @@ struct cdevsw pluartdev =
> > void
> > pluart_attach_common(struct pluart_softc *sc, int console)
> > {
> > - int maj;
> > + int maj, rev;
> > +
> > + rev = UART_PID2_REV(bus_space_read_4(sc->sc_iot, sc->sc_ioh,
> > + UART_PID2));
> > +
> > + printf(": rev %d, %d byte fifo\n", rev, rev < 3 ? 16 : 32);
>
> Should there be constants for the FIFO sizes?
Sure, fixed.
>
> >
> > if (console) {
> > /* Locate the major number. */
> > @@ -159,7 +176,7 @@ pluart_attach_common(struct pluart_softc *sc, int
> > console)
> > break;
> > cn_tab->cn_dev = makedev(maj, sc->sc_dev.dv_unit);
> >
> > - printf(": console");
> > + printf("%s: console\n", sc->sc_dev.dv_xname);
> > SET(sc->sc_hwflags, COM_HW_CONSOLE);
> > }
> >
> > @@ -171,13 +188,26 @@ pluart_attach_common(struct pluart_softc *sc, int
> > console)
> > panic("%s: can't establish soft interrupt.",
> > sc->sc_dev.dv_xname);
> >
> > - bus_space_write_4(sc->sc_iot, sc->sc_ioh, UART_IMSC, (UART_IMSC_RXIM |
> > UART_IMSC_TXIM));
> > + /*
> > + * The transmit FIFO size is set to 3/4 of the actual size as interrupts
> > + * can only be triggered when the FIFO is partially full. Once
> > + * triggered, we know that at least this amount is available in the
> > + * FIFO.
> > + */
> > + if (rev < 3)
> > + sc->sc_fifolen = 24;
> > + else
> > + sc->sc_fifolen = 12;
>
> Have the assignments above been swapped by accident?
Nice catch. That's indeed some last minute sloppy refactoring.
>
> I think the comment could be clearer and more concise; "this amount is
> available" is vague in this context.
I tweaked it to only talk about fractions, better?
diff --git sys/dev/ic/pluart.c sys/dev/ic/pluart.c
index eaa11b6c44b..3479c16c698 100644
--- sys/dev/ic/pluart.c
+++ sys/dev/ic/pluart.c
@@ -99,6 +99,13 @@
#define UART_CR_CTSE (1 << 14) /* CTS hardware flow control
enable */
#define UART_CR_RTSE (1 << 15) /* RTS hardware flow control
enable */
#define UART_IFLS 0x34 /* Interrupt FIFO level select
register */
+#define UART_IFLS_RX_SHIFT 3 /* RX level in bits [5:3] */
+#define UART_IFLS_TX_SHIFT 0 /* TX level in bits [2:0] */
+#define UART_IFLS_1_8 0 /* FIFO 1/8 full */
+#define UART_IFLS_1_4 1 /* FIFO 1/4 full */
+#define UART_IFLS_1_2 2 /* FIFO 1/2 full */
+#define UART_IFLS_3_4 3 /* FIFO 3/4 full */
+#define UART_IFLS_7_8 4 /* FIFO 7/8 full */
#define UART_IMSC 0x38 /* Interrupt mask set/clear
register */
#define UART_IMSC_RIMIM (1 << 0)
#define UART_IMSC_CTSMIM (1 << 1)
@@ -115,8 +122,18 @@
#define UART_MIS 0x40 /* Masked interrupt status
register */
#define UART_ICR 0x44 /* Interrupt clear register */
#define UART_DMACR 0x48 /* DMA control register */
+#define UART_PID0 0xfe0 /* Peripheral identification
register 0 */
+#define UART_PID1 0xfe4 /* Peripheral identification
register 1 */
+#define UART_PID2 0xfe8 /* Peripheral identification
register 2 */
+#define UART_PID2_REV(x) (((x) & 0xf0) >> 4)
+#define UART_PID3 0xfec /* Peripheral identification
register 3 */
#define UART_SPACE 0x100
+#define UART_FIFO_RX_SIZE_R2 16
+#define UART_FIFO_TX_SIZE_R2 12
+#define UART_FIFO_RX_SIZE_R3 32
+#define UART_FIFO_TX_SIZE_R3 24
+
void pluartcnprobe(struct consdev *cp);
void pluartcninit(struct consdev *cp);
int pluartcngetc(dev_t dev);
@@ -150,7 +167,13 @@ struct cdevsw pluartdev =
void
pluart_attach_common(struct pluart_softc *sc, int console)
{
- int maj;
+ int maj, rev;
+
+ rev = UART_PID2_REV(bus_space_read_4(sc->sc_iot, sc->sc_ioh,
+ UART_PID2));
+
+ printf(": rev %d, %d byte fifo\n", rev,
+ rev < 3 ? UART_FIFO_RX_SIZE_R2 : UART_FIFO_RX_SIZE_R3);
if (console) {
/* Locate the major number. */
@@ -159,7 +182,7 @@ pluart_attach_common(struct pluart_softc *sc, int console)
break;
cn_tab->cn_dev = makedev(maj, sc->sc_dev.dv_unit);
- printf(": console");
+ printf("%s: console\n", sc->sc_dev.dv_xname);
SET(sc->sc_hwflags, COM_HW_CONSOLE);
}
@@ -171,13 +194,25 @@ pluart_attach_common(struct pluart_softc *sc, int console)
panic("%s: can't establish soft interrupt.",
sc->sc_dev.dv_xname);
- bus_space_write_4(sc->sc_iot, sc->sc_ioh, UART_IMSC, (UART_IMSC_RXIM |
UART_IMSC_TXIM));
+ /*
+ * The transmit FIFO size is set to 3/4 of the actual size as interrupts
+ * can only be triggered when the FIFO is partially full. Once
+ * triggered, we know that 1/4 of the FIFO size is utilized.
+ */
+ if (rev < 3)
+ sc->sc_fifolen = UART_FIFO_TX_SIZE_R2;
+ else
+ sc->sc_fifolen = UART_FIFO_TX_SIZE_R3;
+ bus_space_write_4(sc->sc_iot, sc->sc_ioh, UART_IFLS,
+ (UART_IFLS_3_4 << UART_IFLS_RX_SHIFT) |
+ (UART_IFLS_1_4 << UART_IFLS_TX_SHIFT));
+ sc->sc_imsc = UART_IMSC_RXIM | UART_IMSC_RTIM | UART_IMSC_TXIM;
+ bus_space_write_4(sc->sc_iot, sc->sc_ioh, UART_IMSC, sc->sc_imsc);
bus_space_write_4(sc->sc_iot, sc->sc_ioh, UART_ICR, 0x7ff);
+ /* Enable FIFO. */
bus_space_write_4(sc->sc_iot, sc->sc_ioh, UART_LCR_H,
- bus_space_read_4(sc->sc_iot, sc->sc_ioh, UART_LCR_H) &
- ~UART_LCR_H_FEN);
-
- printf("\n");
+ bus_space_read_4(sc->sc_iot, sc->sc_ioh, UART_LCR_H) |
+ UART_LCR_H_FEN);
}
int
@@ -197,19 +232,26 @@ pluart_intr(void *arg)
if (sc->sc_tty == NULL)
return 0;
- if (!ISSET(is, UART_IMSC_RXIM) && !ISSET(is, UART_IMSC_TXIM))
+ if (!ISSET(is, UART_IMSC_RXIM) && !ISSET(is, UART_IMSC_RTIM) &&
+ !ISSET(is, UART_IMSC_TXIM))
return 0;
- if (ISSET(is, UART_IMSC_TXIM) && ISSET(tp->t_state, TS_BUSY)) {
- CLR(tp->t_state, TS_BUSY | TS_FLUSH);
- if (sc->sc_halt > 0)
- wakeup(&tp->t_outq);
- (*linesw[tp->t_line].l_start)(tp);
+ if (ISSET(is, UART_IMSC_TXIM)) {
+ /* Disable transmit interrupt. */
+ bus_space_write_4(sc->sc_iot, sc->sc_ioh, UART_IMSC,
+ sc->sc_imsc & ~UART_IMSC_TXIM);
+
+ if (ISSET(tp->t_state, TS_BUSY)) {
+ CLR(tp->t_state, TS_BUSY | TS_FLUSH);
+ if (sc->sc_halt > 0)
+ wakeup(&tp->t_outq);
+ (*linesw[tp->t_line].l_start)(tp);
+ }
}
p = sc->sc_ibufp;
- while (ISSET(bus_space_read_4(iot, ioh, UART_FR), UART_FR_RXFF)) {
+ while (!ISSET(bus_space_read_4(iot, ioh, UART_FR), UART_FR_RXFE)) {
c = bus_space_read_2(iot, ioh, UART_DR);
if (c & UART_DR_BE) {
#ifdef DDB
@@ -322,11 +364,11 @@ pluart_param(struct tty *tp, struct termios *t)
void
pluart_start(struct tty *tp)
{
+ char buf[UART_FIFO_TX_SIZE_R3]; /* fifo max size */
struct pluart_softc *sc = pluart_cd.cd_devs[DEVUNIT(tp->t_dev)];
bus_space_tag_t iot = sc->sc_iot;
bus_space_handle_t ioh = sc->sc_ioh;
- u_int16_t fr;
- int s;
+ int i, n, s;
s = spltty();
if (ISSET(tp->t_state, TS_BUSY | TS_TIMEOUT | TS_TTSTOP))
@@ -336,11 +378,13 @@ pluart_start(struct tty *tp)
goto out;
SET(tp->t_state, TS_BUSY);
- fr = bus_space_read_4(iot, ioh, UART_FR);
- while (tp->t_outq.c_cc != 0 && ISSET(fr, UART_FR_TXFE)) {
- bus_space_write_4(iot, ioh, UART_DR, getc(&tp->t_outq));
- fr = bus_space_read_4(iot, ioh, UART_FR);
- }
+ /* Enable transmit interrupt. */
+ bus_space_write_4(sc->sc_iot, sc->sc_ioh, UART_IMSC, sc->sc_imsc);
+
+ n = q_to_b(&tp->t_outq, buf, sc->sc_fifolen);
+ for (i = 0; i < n; i++)
+ bus_space_write_4(iot, ioh, UART_DR, buf[i]);
+
out:
splx(s);
}
diff --git sys/dev/ic/pluartvar.h sys/dev/ic/pluartvar.h
index 8fcbed14d5c..5181723a066 100644
--- sys/dev/ic/pluartvar.h
+++ sys/dev/ic/pluartvar.h
@@ -45,6 +45,7 @@ struct pluart_softc {
#define COM_SW_MDMBUF 0x08
#define COM_SW_PPS 0x10
int sc_fifolen;
+ int sc_imsc;
u_int8_t sc_initialize;
u_int8_t sc_cua;
