Model number was in the thread, but Parts Finder says it is a CTC169 manu 1995. This set is dated 1990 on the rear Model F27194SM I replaced the capacitor and no change except a little more narrow..I grabbed one from another chassis.. I replaced the linearity coil and set was still bowed, with pincushion and a lot more narrow..pulled this from another chassis. The coil I used from another chassis which would explain the narrow pic, but it was still bowed, so I don't think a new one will help. With the different capacitor C4403 the picture is not quite as wide, but since I still see the bowing(hourglass) I assume a new one won't fix that. Any other ideas? Jeff Dougherty Intrepid Video TV/VCR 263 S Front St Steelton PA 17113 fax...717-564-4952 www.intrepid-video.com www.tech-repair.net
----- Original Message ----- From: "Wayne Vanaman" <[EMAIL PROTECTED]> To: "ELECTRONICS PROFESSIONALS LIST" <[EMAIL PROTECTED]> Sent: Saturday, January 10, 2004 11:07 AM Subject: Re: [Techs] TA RCA CTC167CS Pincushion**Urgent/ c4403. Model number please Wayne Vanaman Omega Electronics 6904 W Fairfield Dr Pensacola, Fl. 32506-3310 [EMAIL PROTECTED] WWW.PensacolaTVRepair.Com 850-456-5995 voice 850-458-6369 fax ----- Original Message ----- From: <[EMAIL PROTECTED]> To: "ELECTRONICS PROFESSIONALS LIST" <[EMAIL PROTECTED]> Sent: Saturday, January 10, 2004 8:56 AM Subject: Re: [Techs] TA RCA CTC167CS Pincushion**Urgent/ > I called the customer yesterday to tell them the set was ready, when I noticed the pincushion problem. > This set probably had this problem before the vertical failure, but customer let it go. > Customer wants set today...and though I appreciate everyone's input, this unit DOES NOT have any of the > components in this pincushion circuit. I had a CTC156H pretty much the exact same thing.. Pincushion > circuit is silk screened on board, but nothing there. > I think most of you can understand the predicament with this customer... > If anyone can advise me how to adjust the pincushion or fix for this problem, I'd be grateful. > Set has HOT with internal damper..I replaced HOT with no luck. > Thank you. > > > > Jeff Dougherty > Intrepid Video TV/VCR > 263 S Front St > Steelton PA 17113 > fax...717-564-4952 > www.intrepid-video.com www.tech-repair.net > > ----- Original Message ----- > From: <[EMAIL PROTECTED]> > To: "Tech List" <[EMAIL PROTECTED]> > Sent: Friday, January 09, 2004 7:36 PM > Subject: [Techs] TA RCA CTC167CS Pincushion > > > Model F27194SM.(Similar to CTC156H) > Unit came in with no vertical. After several hours of troubleshooting, found one of the terminals on the > yoke broken..repaired. > During all this time, I had to pull the CRT socket so I didn't burn the CRT. Another tech must have had > this set because someone put the CRT back without lining it up and two pins were shorted.. G1 and Red K, I > think.. > After the vertical problem, I found retrace on the screen. Found shorted transistor on main > board..replaced. > Now, I have severe pincushion on sides OSD and TV are bowed. I can find no pincushion circuit on this > board, yet Fix Finder references some components. I see the markings on this PCB, but nothing at these > locations. > Can someone tell me how to adjust the pincushion? I see on adjustments for horizontal size or pincushion.. > Thank you. > _________________________________________ Please include original text when replying to this email. Once you get your unit repaired, please post the fix to the group. Order your tech repair CD today, Version 3.0 only $49.00-more monitor tips-user friendly program. [EMAIL PROTECTED] www.tech-repair.net ______ Techs mailing list [EMAIL PROTECTED] http://intrepid-video.com/mailman/listinfo/techs_intrepid-video.com Go to the link above and scroll to the bottom to enter your email address
