Sure.

Tel-Tek Electronics
Ontario-Canada
[EMAIL PROTECTED]

----- Original Message ----- 
From: "Mark Wentowski" <[EMAIL PROTECTED]>
To: "ELECTRONICS PROFESSIONALS LIST" <[EMAIL PROTECTED]>
Sent: Saturday, April 03, 2004 4:03 PM
Subject: RE: [Techs] Home Service Callls.


> I wonder if the IRS monitors these lists.
>
> Mark Wentowski
> Perry Hill Electronics
> 3836 Harrison Rd.
> Montgomery AL 36109
> phone: (334)279-5622
> fax:   (334)273-9050
> [EMAIL PROTECTED]
>
> -----Original Message-----
> From: [EMAIL PROTECTED]
> [mailto:[EMAIL PROTECTED] Behalf Of LeRoy Westlund
> Sent: Saturday, April 03, 2004 12:19 PM
> To: ELECTRONICS PROFESSIONALS LIST
> Subject: [Techs] Home Service Callls.
>
>
> Little ole Ladies are the best for home service calls.
> I just did one yesterday. I drove 12 miles, but, I had to go over that
> direction anyway, so the gas didn't apply.
> All I had to do was un-plud the Sat. RX for a few seconds, and plug it in,
> so it would re-set itself. The TV had a vertical retrace problem
> also,...but, she said she was used to that, and since it was an OLD 25"
> Zenith console, she declined my estimate of $95 to pull the chassis, and
> replace the e-caps in the vertical. I just charged her $30, and happly
went
> on me way. Can't charge much for a service call around here. I was lucky
to
> get the minimum amount out of her,...although she didn't complain. She
just
> went in the bedroom, and came back with $30 CASH. That's the most $$$ I've
> made in the last 3 weeks ! (and that's NO lie.)
> ;-)
>
> LLW
>
> LeRoy Westlund
> Westlund TV & Electronics
> 97 North Main                                "Where there's a will,...
> Centerfield, UT 84622-0087           There's always a way."
> Ph./Fax  435-528-3822
> mailto:[EMAIL PROTECTED]
>
> -----Original Message-----
> From: Ed Gaidies <[EMAIL PROTECTED]>
> To: ELECTRONICS PROFESSIONALS LIST <[EMAIL PROTECTED]>
> Date: Saturday, April 03, 2004 10:12 AM
> Subject: Re: [Techs] Re: Fixed..NAP HD2717C101 27B800,no video..(was
> vertical problem)
>
>
> >Do what you need to survive. I may have to start doing Service Calls
again.
> >
> >-Ed-
> >
> >
> >
> >Tel-Tek Electronics
> >Ontario-Canada
> >
> >[EMAIL PROTECTED]
> >----- Original Message -----
> >From: "LeRoy Westlund" <[EMAIL PROTECTED]>
> >To: "ELECTRONICS PROFESSIONALS LIST" <[EMAIL PROTECTED]>
> >Sent: Saturday, April 03, 2004 11:54 AM
> >Subject: [Techs] Re: Fixed..NAP HD2717C101 27B800,no video..(was vertical
> >problem)
> >
> >
> >> Hi Mark, and fellow techs.
> >> I just put FREE ESTIMATES back up on my outside sign,...and I don't
want
> >> anybody to give me any sh*t about it. I've tried it BOTH ways, and I
> don't
> >> want to drive anymore of my customers to Wal-Mart any sooner then I
have
> >to.
> >> A FREE estimate is just THAT,...if they want a more precise
> >> diagnosis,...then they will still have to pay $1 per inch for the size
of
> >> the screen. $20 for 19", $25 for 25-27", and $35 for 32-40". $50-100
for
> >> PTVs.
> >> I will also require the remote control to be brought in, to qualify for
> >the
> >> FREE estimate.
> >> Cause I plan to repair, and sell them as used sets, and nobody wants to
> >buy
> >> a used TV with out a remote control. I plan to sell them for 1/2 the
> price
> >> that Wal-Mart charges for a new one. After all, the junk they sell is
not
> >> any better then a good used TV, that has been reconditioned properly.
Of
> >> course,...that has to be part of my sales pitch.
> >> I will have to convence them of that.
> >> In cases where the set is obviously a junker, I won't even accept it to
> >> start with. I will give them an unreasonably high estimate, to
discourage
> >> them from even leaving it at my facility. My plan is to get some of the
> >> BEST, repairable sets, before they junk them to buy new. I am certain
> that
> >> there are TOO many 25-35 inch sets, that are being junked, that could
be
> >> fixed and sold at a profet. I am doing  this because I am desperate. If
I
> >> had many customers like the good ole days,...I would be more picky,
but,
> >> things are getting scary around here. Dead, dead,...and more dead each
> day
> >> that passes. Hope things are better for you guys in your resective
areas.
> >> You might say,...that I am making a final stab at it. Beat Wally World
at
> >> their own game, and undercut them by 50%. HO, ho,.HA, ha, HE, he,.....
> >> ;-)
> >>
> >> LLW
> >>
> >> LeRoy Westlund
> >> Westlund TV & Electronics
> >> 97 North Main                                "Where there's a will,...
> >> Centerfield, UT 84622-0087           There's always a way."
> >> Ph./Fax  435-528-3822
> >> mailto:[EMAIL PROTECTED]
> >>
> >> -----Original Message-----
> >> From: Mark Wentowski <[EMAIL PROTECTED]>
> >> To: ELECTRONICS PROFESSIONALS LIST <[EMAIL PROTECTED]>
> >> Date: Friday, April 02, 2004 11:57 PM
> >> Subject: RE: [Techs] Fixed..NAP HD2717C101 27B800,no video..(was
> >> verticalprblm)
> >>
> >>
> >> >Jeff's a damned good tech Leroy. Nobody ever doubted that.
> >> >
> >> >What's going on in Utah. Fun fun fun
> >> >
> >> >Mark Wentowski
> >> >Perry Hill Electronics
> >> >3836 Harrison Rd.
> >> >Montgomery AL 36109
> >> >phone: (334)279-5622
> >> >fax:   (334)273-9050
> >> >[EMAIL PROTECTED]
> >> >
> >> >-----Original Message-----
> >> >From: [EMAIL PROTECTED]
> >> >[mailto:[EMAIL PROTECTED] Behalf Of LeRoy Westlund
> >> >Sent: Saturday, April 03, 2004 12:21 AM
> >> >To: ELECTRONICS PROFESSIONALS LIST
> >> >Subject: Re: [Techs] Fixed..NAP HD2717C101 27B800,no video..(was
> >> >verticalprblm)
> >> >
> >> >
> >> >Well,....I'll be damned !
> >> >I wish I hadn't thrown mine away already.
> >> >Jeff,...you are a better tech then me.
> >> >Congradulations.
> >> >;-(
> >> >
> >> >LLW
> >> >
> >> >LeRoy Westlund
> >> >Westlund TV & Electronics
> >> >97 North Main                                "Where there's a will,...
> >> >Centerfield, UT 84622-0087           There's always a way."
> >> >Ph./Fax  435-528-3822
> >> >mailto:[EMAIL PROTECTED]
> >> >
> >> >-----Original Message-----
> >> >From: Doug Keller <[EMAIL PROTECTED]>
> >> >To: ELECTRONICS PROFESSIONALS LIST <[EMAIL PROTECTED]>
> >> >Date: Friday, April 02, 2004 11:11 AM
> >> >Subject: Re: [Techs] Fixed..NAP HD2717C101 27B800, no video..(was
> >> >verticalprblm)
> >> >
> >> >
> >> >>Don't applaud,..........throw money!!!
> >> >>
> >> >>Doug Keller
> >> >>Wis-Kel Electronics
> >> >>101 Freeland Ave.
> >> >>Terra Alta, WV
> >> >>USA        26764
> >> >>[EMAIL PROTECTED]
> >> >>[EMAIL PROTECTED]
> >> >>http://www.tech-assist.org
> >> >>"Learn from the mistakes of others, because you
> >> >>won't live long enough to make them all yourself"
> >> >>
> >> >>
> >> >>
> >> >>
> >> >>
> >> >>Intrepid Video Support wrote:
> >> >>
> >> >>>Persistence pays off again...
> >> >>>After spending a lot of time in the vertical section, I came to the
> >> >conclusion my final fault was not in
> >> >>>this circuit. It was confusing since removing the vertical connector
> >for
> >> >the yoke, I got a horizontal
> >> >>>line..
> >> >>>In my checks of IC271, I found my voltage low on pin 18(s/b 5.1v).
> >> Lifting
> >> >the pin and the voltage came
> >> >>>up.
> >> >>>On connector J251, I had 1K ohms resistance pin 5 to ground,
> unsoldered
> >> >and isolated problem to CRT board
> >> >>>as other techs had suggested. I thought I ruled the CRT board out as
> >> shows
> >> >video on the scope on each IC
> >> >>>and injected video and the screen lit up.
> >> >>>Tracing the path back I found the final two video out IC's(that I
did
> >not
> >> >replace in the beginning)
> >> >>>actually had pins 5 shorted to ground, lifted to confirm that pins
4,5
> >> >were shorted.
> >> >>>Replaced IC's and screen lit up, though decreased vertical...I put
the
> >> >original EEPROM back in set and
> >> >>>picture was perfect.
> >> >>>I appreciate everyone that sent schematics and offered their help. I
> >> >couldn't have completed this task
> >> >>>without the help from this list..
> >> >>>Thank you.
> >> >>>
> >> >>>Jeff Dougherty
> >> >>>Intrepid Video TV/VCR
> >> >>>263 S Front St
> >> >>>Steelton PA 17113
> >> >>>fax...717-564-4952
> >> >>>www.intrepid-video.com www.tech-repair.net
> >> >>>
> >> >>>----- Original Message -----
> >> >>>From: "Intrepid Video Support" <[EMAIL PROTECTED]>
> >> >>>To: "ELECTRONICS PROFESSIONALS LIST" <[EMAIL PROTECTED]>
> >> >>>Sent: Wednesday, March 31, 2004 1:04 PM
> >> >>>Subject: [Techs] 2nd REQ... TA...NAP HD2717C101 27B800,no
video..(was
> >> >vertical prblm)
> >> >>>
> >> >>>
> >> >>>Going with a fresh post on this one. I still can't find the problem.
> >> >>>First thing, I found the resistors and diodes for the 13 (-/+) lines
> >bad,
> >> >replaced those and shorted
> >> >>>vertical IC.
> >> >>>Then, I had raster that was red with retrace, found the RED video IC
> >bad
> >> >on CRT board. Also, R50
> >> >>>open..replaced, then back to no video.
> >> >>>I've tried three more vertical out IC's all OEM and NTE, still no
> >video.
> >> >With the NTE in, I get some video
> >> >>>very top of screen about 1/4 inch across.
> >> >>>On IC271, 46/47, voltages were about a volt low and wave forms were
> low
> >> >p-p, replaced IC..no fix.
> >> >>>Wave forms in/out of SAW filter are OK.
> >> >>>On pin 1 over vertical yoke, which comes from pin 5 of vertical wave
> >form
> >> >shows about 50 vpp, very high.
> >> >>>Pin 6,7 of vertical show low pp voltage.
> >> >>>I've went over and over my traces solder, replace the resistors and
> >diode
> >> >with OEM numbers, went over the
> >> >>>CRT board again.
> >> >>>If I remove the vertical plug, I do get a horizontal line and the
> power
> >> >LED flashes. I checked the yoke
> >> >>>and it is about 1 ohm off from one on another set.
> >> >>>I have the schematic of this section, but am not sure what is causin
g
> >> >these wave forms to vary.
> >> >>>I put in another Philips IC and the wave forms are even farther off.
> >> >>>Any other ideas before I scrap this set...I've done many of these B8
> >for
> >> >the same problem and have never
> >> >>>had this type of trouble,
> >> >>>Thank you.
> >> >>>
> >> >>>Jeff Dougherty
> >> >>>
> >> >>>
> >> >>>_______________________________________________
> >> >>>Tech Repair CD...order your just $49.00 plus shipping...One year of
> >> >updates free.
> >> >>>www.intrepid-video.com www.tech-repair.net
> >> >>>Techs mailing list
> >> >>>[EMAIL PROTECTED]
> >> >>>http://intrepid-video.com/mailman/listinfo/techs_intrepid-video.com
> >> >>>
> >> >>>
> >> >>>
> >> >>>
> >> >>>
> >> >>
> >> >>_______________________________________________
> >> >>Tech Repair CD...order your just $49.00 plus shipping...One year of
> >> updates
> >> >free.
> >> >>www.intrepid-video.com www.tech-repair.net
> >> >>Techs mailing list
> >> >>[EMAIL PROTECTED]
> >> >>http://intrepid-video.com/mailman/listinfo/techs_intrepid-video.com
> >> >>
> >> >
> >> >
> >> >_______________________________________________
> >> >Tech Repair CD...order your just $49.00 plus shipping...One year of
> >updates
> >> >free.
> >> >www.intrepid-video.com www.tech-repair.net
> >> >Techs mailing list
> >> >[EMAIL PROTECTED]
> >> >http://intrepid-video.com/mailman/listinfo/techs_intrepid-video.com
> >> >
> >> >
> >> >
> >> >_______________________________________________
> >> >Tech Repair CD...order your just $49.00 plus shipping...One year of
> >updates
> >> free.
> >> >www.intrepid-video.com www.tech-repair.net
> >> >Techs mailing list
> >> >[EMAIL PROTECTED]
> >> >http://intrepid-video.com/mailman/listinfo/techs_intrepid-video.com
> >> >
> >>
> >>
> >> _______________________________________________
> >> Tech Repair CD...order your just $49.00 plus shipping...One year of
> >updates free.
> >> www.intrepid-video.com www.tech-repair.net
> >> Techs mailing list
> >> [EMAIL PROTECTED]
> >> http://intrepid-video.com/mailman/listinfo/techs_intrepid-video.com
> >>
> >
> >
> >_______________________________________________
> >Tech Repair CD...order your just $49.00 plus shipping...One year of
updates
> free.
> >www.intrepid-video.com www.tech-repair.net
> >Techs mailing list
> >[EMAIL PROTECTED]
> >http://intrepid-video.com/mailman/listinfo/techs_intrepid-video.com
> >
>
>
> _______________________________________________
> Tech Repair CD...order your just $49.00 plus shipping...One year of
updates
> free.
> www.intrepid-video.com www.tech-repair.net
> Techs mailing list
> [EMAIL PROTECTED]
> http://intrepid-video.com/mailman/listinfo/techs_intrepid-video.com
>
>
>
> _______________________________________________
> Tech Repair CD...order your just $49.00 plus shipping...One year of
updates free.
> www.intrepid-video.com www.tech-repair.net
> Techs mailing list
> [EMAIL PROTECTED]
> http://intrepid-video.com/mailman/listinfo/techs_intrepid-video.com
>


_______________________________________________
Tech Repair CD...order your just $49.00 plus shipping...One year of updates free.
www.intrepid-video.com www.tech-repair.net
Techs mailing list
[EMAIL PROTECTED]
http://intrepid-video.com/mailman/listinfo/techs_intrepid-video.com

Reply via email to