Pinout is as follows - I think - remember that this is a work in progress 1 - no connection 2 - alarm output - High = alarm, low = normal (TTL) 3 - probably 'reference fail' - High = fail, low = normal (TTL) 4 - EFC okay - High if 4V8 < EFC < 7V5 else low (TTL) 5 - no connection 6 - buffered EFC voltage for oscillator 7 - no connection 8 - +10V reference output from oscillator - doesn't seem to be used for anything 9 - +5V supply (input) 10 - External EFC input - only used when reference fails 11 - ground 12 - " 13 - " 14 - +24V supply (input) for oscillator 15 - +15V supply (input) You talked about BNC. Did you mean TNC? My unit has TNC and SMA connectors. The SMA connectors are all outputs from the oscillator. J3 (TNC) is the input from an external 5 MHz reference. J4 (TNC) is another output from the oscillator. Approximate output levels are as follows: J2 - +7 dbm J4 - 0 dbm J5 - 0 dbm J6 - +7 dbm The purpose of the box is to discipline the internal oscillator to an external reference and then distribute the oscillator's signal to four outputs. The level of the external reference can vary over an unknown range because there's an internal AGC circuit. I haven't figured out the parameters of the low pass filter used on the output of the phase detector. Just for laughs I took the 10 MHz output of a Navsync CW-12 GPS board, divided it by 2, and fed it into the reference input. The result wasn't pretty. Obviously, the circuit wants a smoother source. On mine, the oscillator was defective. I had to hack into it to fix a broken wire on the output transformer. I started a message thread a few months back about how to hack into an oscillator - check the archive if you need to. Remember Engineering Rule #1 - Tune for minimum smoke! Ed Richard W. Solomon wrote:
Was it that good a deal ?? I'll share my secret, I use Gixen to snipe on e-Pay. Sometimes it works, sometimes not. Do you know the connections for the DB-15 connector ? Then I can do the smoke test !! Also what are the BNC and SMA connectors for ? Basically, I know nothing but would appreciate any help. I will likewise share my findings. 73, Dick, W1KSZ -----Original Message----- From: Ed Palmer [1]<[email protected]> Sent: May 14, 2009 1:10 PM To: Discussion of precise time and frequency measurement [2]<[email protected]> Subject: Re: [time-nuts] Help ID 5 MHz Distribution Box Since you beat me by *THREE SECONDS* I shouldn't help you, but I have one of these boxes and have partially figured it out. What do you want to know? Ed Richard W. Solomon wrote: I picked up a box from "over there" that says ..."5 MH REF DISTRIB"... , which I assume stands for 5 MHz Reference Distribution. It was made by Satellite Transmission Systems of Hauppagge, NY. 2 BNC connectors on one end, 3 SMA's a Red LED Alarm light and a DB-15 connector. A real long shot, I know, but on the off-chance, does anyone know anything about this ? Anyone know if the company still exists ? Thanks, Dick, W1KSZ _______________________________________________ time-nuts mailing list -- [3][email protected] To unsubscribe, go to [4]https://www.febo.com/cgi-bin/mailman/listinfo/time-nuts and follow the instructions there. _______________________________________________ time-nuts mailing list -- [5][email protected] To unsubscribe, go to [6]https://www.febo.com/cgi-bin/mailman/listinfo/time-nuts and follow the instructions there. References 1. mailto:[email protected] 2. mailto:[email protected] 3. mailto:[email protected] 4. https://www.febo.com/cgi-bin/mailman/listinfo/time-nuts 5. mailto:[email protected] 6. https://www.febo.com/cgi-bin/mailman/listinfo/time-nuts _______________________________________________ time-nuts mailing list -- [email protected] To unsubscribe, go to https://www.febo.com/cgi-bin/mailman/listinfo/time-nuts and follow the instructions there.
