Hi, In many military Russian locator and other eqmnt, also from the east block microwave units/chain used the shoulder screw to have perfect alignment between wave guides... I was the same with the Czech Republic radars too..... I have been operated many above mentioned units......... Rgds Ernie.
-----Original Message----- From: [email protected] To: Time-Nuts <[email protected]> Sent: Sun, Sep 19, 2010 2:49 pm Subject: Re: [time-nuts] Semi-OT: Hardware for WR-90 waveguide sections? Robert is obviously correct, however you would be very hard pressed to be able o measure the difference between shoulder screws and regular screws in ractice, either through insertion loss, VSWR or power handling. So much so that I have never seen shoulder screws used on rectangular waveguide, ven on very high power and very low noise equipment. Double ridge waveguide is different story. I have seen occasional waveguide arcs on very high power equipment starting at he junction between components or sections of waveguide, but not sufficiently r often enough or consistently enough to be able to pin it to the use of egular screws. Maybe I have been doing it wrong all along :) hanks for the reminder!!! Didier KO4BB Sent from my Verizon Wireless BlackBerry -----Original Message----- rom: "J. Forster" <[email protected]> ender: [email protected] ate: Sun, 19 Sep 2010 03:50:07 o: Discussion of precise time and frequency measurement<[email protected]> eply-To: [email protected], Discussion of precise time and frequency measurement <[email protected]> ubject: Re: [time-nuts] Semi-OT: Hardware for WR-90 waveguide sections? The shoulder screw is an interesting idea, but I've seen (and taken apart) ots and lots of waveguide over the decades, including brand new stuff rom major manufacturers and mil contractors. I've never seen a shoulder crew used. FWIW, -John ================= > Hi, Not strictly true. Material is not important apart from environmental (corrosion) issues, but that is not the only concern. WG-16 (British) / WR 90 flanges are not dowelled. They rely on the fastners for alignment. The correct fastners are 5/32" shoulder screws (0.1557" dia 6-32 thread). The precsion shoulder locates the flanges. 5/32" bolts (a bolt has a plain shank) are a good second choice but you will probably have to pack them with washers as the grip length won't match ;-) If you have to use screws, at least align two diagonal holes with 5/32" dowels while nipping up the first two screws. Robert G8RPI. --- On Sun, 19/9/10, jimlux <[email protected]> wrote: From: jimlux <[email protected]> Subject: Re: [time-nuts] Semi-OT: Hardware for WR-90 waveguide sections? To: "Discussion of precise time and frequency measurement" <[email protected]> Date: Sunday, 19 September, 2010, 4:13 [email protected] wrote: > Not completely OT, as stable and accurate timebases are very useful in > microwave systems... > What's the proper hardware to use for connecting WR-90 (10GHz) waveguide > sections? I figure 8-32 brass or stainless, avoiding anything magnetic. > whatever fits through the holes in the flanges. #8 requires a 0.187 hole, #6 requires a 0.156, #4 is 0.125, #2 is 0.109 One reference I have says WR90 has 0.169" holes, so that's #6 hardware. Whether it is magnetic or not doesn't make any difference. _______________________________________________ time-nuts mailing list -- [email protected] To unsubscribe, go to https://www.febo.com/cgi-bin/mailman/listinfo/time-nuts and follow the instructions there. _______________________________________________ time-nuts mailing list -- [email protected] To unsubscribe, go to https://www.febo.com/cgi-bin/mailman/listinfo/time-nuts and follow the instructions there. _______________________________________________ ime-nuts mailing list -- [email protected] o unsubscribe, go to https://www.febo.com/cgi-bin/mailman/listinfo/time-nuts nd follow the instructions there. ______________________________________________ ime-nuts mailing list -- [email protected] o unsubscribe, go to https://www.febo.com/cgi-bin/mailman/listinfo/time-nuts nd follow the instructions there. _______________________________________________ time-nuts mailing list -- [email protected] To unsubscribe, go to https://www.febo.com/cgi-bin/mailman/listinfo/time-nuts and follow the instructions there.
