Hi The same basic equations apply (as you point out) to any receiver. Lay down enough on channel noise power and the receiver doesn't have much of a chance. Nothing magic or terribly hard to figure out. Easy to do wideband at "I could use a baseball bat" to "I could use a bow and arrow" type ranges.
Because it's easy to do, it happens all the time. Fire up some hair dryers at close range and they do a fine jamming job. Some of the jamming is electrical, some of it is the fact you can't hear anything over the noise they are making. An axe (or good sling shot) is a fine way to take out a cell site and you can get them just about anywhere. Jamming GPS isn't even going to make them drop a call for at least a day or more. It won't make airplanes drop from the sky either. Taking out cell sites one at a time isn't a real big deal. It's a rare area that's covered by only one site. They go in and out of service now and then, it mostly goes un-noticed. If it is noticed, it's by a small number of people. I have a nasty suspicion that sites that fail don't get fixed as fast as they might for just those reasons. The timing setups are indeed fragile. They could be improved quite a bit. They aren't so fragile that they melt down immediately when a single fault occurs. Lots of axes (or a big hurricane) are by far the more likely source of full system failure. Bob -----Original Message----- From: [email protected] [mailto:[email protected]] On Behalf Of jimlux Sent: Tuesday, November 23, 2010 9:37 AM To: Discussion of precise time and frequency measurement Subject: Re: [time-nuts] GPS jamming susceptibility John Green wrote: > > jamming anyone's GPS. A while back, I was looking at one of those > It doesn't look capable of putting out > more than 50 milliwatts or so into a 2 inch antenna The GPS antenna is perhaps 35 feet away > with a cinder block wall, a brick wall, and a metal roof in between. I > also put a 15 Db attenuator between it and the antenna with almost the > same result. > down. Has anyone here had any actual experience testing GPS receivers > for susceptibility? > OK... typical received signal at a GPS receiver (L1) is on the order of -130dBm. Thermal noise floor (assuming noiseless receiver and no losses) is -114 dBm in 1 MHz BW. Remember, the typical GPS is a single bit quantizer, which works just fine considering the signal is 20dB below the noise floor. So, let's do a little link calculation: 32+20log10(1500)+20log10(.010) between isotropic antennas (which is not a bad starting point for your jammer and the GPS).. 32+64-40 -> a link loss of 56 dB.. you're radiating +17dBm, so let's call it -40dBm into the GPS.. Yep, jamming is almost assured.. But at that kind of power, you'd jam almost ANY receiver that's trying to receive a signal at -130dBm. 90dB instantaneous dynamic range is pretty good when you can't use a filter to remove the interfering signal (e.g. a HF receiver has a narrow band filter in the IF to solve this problem). realistically, you need about, say, 10 dB J/S so you'd need -120 dBm into the receiver from the jammer. A microwatt 10 meters away would do it nicely. Inverse square helps a bit.. if you were 1 km away, your interfering 50mW signal would be down another 40 dB.. -80dBm. 10km away, your jammer is down into the area where it probably won't jam all the time. Obviously, *real* radios that need reliable GPS reception do things to make life easier. Aside from using 1.5-2 bit detection, or signal excisers, etc. There are also techniques that rely on looking at the post correlation signal (where the interferer is suppressed to a certain extent): with modern signal processing, you can correlate against all possible phases of the code in one shot, for instance. _______________________________________________ time-nuts mailing list -- [email protected] To unsubscribe, go to https://www.febo.com/cgi-bin/mailman/listinfo/time-nuts and follow the instructions there. _______________________________________________ time-nuts mailing list -- [email protected] To unsubscribe, go to https://www.febo.com/cgi-bin/mailman/listinfo/time-nuts and follow the instructions there.
