Essentially its a single processor timing generator. Using a SXb 28 pin micro preprogrammed with european GRIs since na are all gone. It was never published really. I shared it with Antonio. The programs written in basic language so very adaptable. Essentially to select a gri set a dip switch and press reset. 2 connections in the 2000c and power and ground. Wasn't sure there was much interest would have to dig the info up and put it on Diddiers site or Stanleys site. Regards. Paul.
On Tue, Dec 28, 2010 at 9:42 AM, Thomas Linbeck <[email protected]>wrote: > Paul, > I have missed part of a thread somewhere ... Addressing the mod for the > 2000C. I would like to find out a bit more about what you have done. > Could > you point me in the right direction? Thanks. > Tom > > -----Original Message----- > From: [email protected] [mailto:[email protected]] On > Behalf Of paul swed > Sent: Wednesday, December 22, 2010 1:04 PM > To: Discussion of precise time and frequency measurement > Subject: Re: [time-nuts] free: Astron 2000C LORAN receiver > > Quite right its 3 digit thats why I built a mod for the 2000c using a SXb > micro single chip itty bitty 4 digit GRI generator. Total cost $5 in parts > and its not a kit. Just a chip dip switch and reset button. > A fellow in Italy is using it with a 2000c as am I. > Just hate to waste great gear because of cheap politics. > Regards > Paul. > > On Wed, Dec 22, 2010 at 12:35 PM, Robert Darlington > <[email protected]>wrote: > > > Ah, good point. I believe this is the case too. I have a taker now > and > > am waiting to hear back (I pointed this out to him). > > > > -Bob > > > > On Wed, Dec 22, 2010 at 9:44 AM, Poul-Henning Kamp <[email protected] > > >wrote: > > > > > In message > > ><[email protected] > > >, > > > Robe > > > rt Darlington writes: > > > >Hi guys, > > > > > > > >I live in New Mexico which means my LORAN receiver is pretty much a > > > >boat anchor. This is what the thing looks like: > > > > > > > > > http://www.recycledgoods.com/products/Austron-2000C-Loran-C-Precision- > > Time-and-Frequency-Receiver.html > > > > > > As far as I can see, it is a "3-digit-GRI" model, so it will not be > > > able to receive european chains. > > > > > > -- > > > Poul-Henning Kamp | UNIX since Zilog Zeus 3.20 > > > [email protected] | TCP/IP since RFC 956 > > > FreeBSD committer | BSD since 4.3-tahoe > > > Never attribute to malice what can adequately be explained by > > incompetence. > > > > > > _______________________________________________ > > > time-nuts mailing list -- [email protected] To unsubscribe, go to > > > https://www.febo.com/cgi-bin/mailman/listinfo/time-nuts > > > and follow the instructions there. > > > > > _______________________________________________ > > time-nuts mailing list -- [email protected] To unsubscribe, go to > > https://www.febo.com/cgi-bin/mailman/listinfo/time-nuts > > and follow the instructions there. > > > _______________________________________________ > time-nuts mailing list -- [email protected] To unsubscribe, go to > https://www.febo.com/cgi-bin/mailman/listinfo/time-nuts > and follow the instructions there. > > > _______________________________________________ > time-nuts mailing list -- [email protected] > To unsubscribe, go to > https://www.febo.com/cgi-bin/mailman/listinfo/time-nuts > and follow the instructions there. > _______________________________________________ time-nuts mailing list -- [email protected] To unsubscribe, go to https://www.febo.com/cgi-bin/mailman/listinfo/time-nuts and follow the instructions there.
