The blue labels just barely visible behind the control panel in the
close-up pictures look an awful lot like actual Sulzer labels. I wonder
if instead of being licensed it was actually OEM'd and they just
replaced the front panel with a purpose-built one.
John
----
On 8/25/2011 12:23 PM, Robert Atkinson wrote:
I'm pretty sure Racal made these. They are of consistent design over different
models and many years and are unlike any other manufacturers OXCO I've seen.
Racal were old school and did prettymuch everything themselves. The did do what
appears to be a licence built Sulzer though. The MA-259, see
http://www.radiomuseum.org/r/racal_precision_frequency_stan.html
Regards,
Robert G8RPI.
--- On Thu, 25/8/11, Bob Camp<[email protected]> wrote:
From: Bob Camp<[email protected]>
Subject: Re: [time-nuts] Racal 9420 OCXO
To: "'Discussion of precise time and frequency measurement'"<[email protected]>
Date: Thursday, 25 August, 2011, 17:01
Hi
Do we know for sure that Racal actually made these OCXO's in house?
My *guess* is that they were made by various companies over the years and
sold to Racal. The "return for service" would have been a return to Racal
and then they forward it to the people who made it...
Bob
-----Original Message-----
From: [email protected] [mailto:[email protected]] On
Behalf Of paul swed
Sent: Wednesday, August 24, 2011 5:10 PM
To: Discussion of precise time and frequency measurement
Subject: Re: [time-nuts] Racal 9420 OCXO
Kind of amazing what time-nuts have in there secret documentation.
Though I do not need this thanks for sharing.
Regards
Paul
WB8TSL
On Wed, Aug 24, 2011 at 4:05 PM, Robert Atkinson
<[email protected]>wrote:
Hi,
I've attached a copy of the catalogue specification for Racals OCXOs. They
do have electronic trim as standard. They are used in the 9478 frequency
standard. The 9478 service manual specfically states that no information
on
the OCXOs is provided and they must be returned to Racal or appointed
agents
for repair.
Robert G8RPI
--- On Wed, 24/8/11, [email protected]<[email protected]> wrote:
From: [email protected]<[email protected]>
Subject: Re: [time-nuts] Racal 9420 OCXO
To: [email protected]
Date: Wednesday, 24 August, 2011, 16:03
In a message dated 24/08/2011 00:03:19 GMT Daylight Time,
[email protected] writes:
I don't think Racal released circuit diagrams of any of their ovens. I
have traced out the circuit of the rapid warm up oven found in a lot of
receivers, the 9442-12 and have fixed those, there is a ceramic cap that
frequently goes wonky. The two 9420s I have fixed were just broken
wires; they seem to have used PVC insulated wire which degrades... I
haven't done the homework on those yet.
The 9420s I have do have an EFC input as well as a stabilised Voltage
out to feed it, and in the receivers I have that use it [RA1795] the
fine setting is done from that, coarse setting from the top adjustment.
-------------------------
Hi Dan
I've taken a further look at the RA1794 manual and see now that it does
confirm a fine tune pot being available when using the 9420.
Having opened up this oscillator I find there are connections to every
pin
on the B7G connector so will assume until proven otherwise that it does
meet the interface spec shown in the 1794 manual.
I suspect the comments I've seen claiming most do not have the EFC option
is more a case that in many installations it isn't used, which isn't
quite
the same thing.
Thanks again for your comments.
regards
Nigel
_______________________________________________
time-nuts mailing list -- [email protected]
To unsubscribe, go to
https://www.febo.com/cgi-bin/mailman/listinfo/time-nuts
and follow the instructions there.
_______________________________________________
time-nuts mailing list -- [email protected]
To unsubscribe, go to
https://www.febo.com/cgi-bin/mailman/listinfo/time-nuts
and follow the instructions there.
_______________________________________________
time-nuts mailing list -- [email protected]
To unsubscribe, go to
https://www.febo.com/cgi-bin/mailman/listinfo/time-nuts
and follow the instructions there.
_______________________________________________
time-nuts mailing list -- [email protected]
To unsubscribe, go to https://www.febo.com/cgi-bin/mailman/listinfo/time-nuts
and follow the instructions there.
_______________________________________________
time-nuts mailing list -- [email protected]
To unsubscribe, go to https://www.febo.com/cgi-bin/mailman/listinfo/time-nuts
and follow the instructions there.
_______________________________________________
time-nuts mailing list -- [email protected]
To unsubscribe, go to https://www.febo.com/cgi-bin/mailman/listinfo/time-nuts
and follow the instructions there.
