Dear John, Your response is welcome. My square signal input is 3.3V and 50% duty cycle. Low end 0.5V, High end 2.7V.
Will I be able to make it without the bypass? Or should I start warming the soldering station? Thanks! Edgardo Molina Dirección IPTEL www.iptel.net.mx T : 55 55 55202444 M : 04455 10045822 Piensa en Bits SA de CV Información anexa: CONFIDENCIALIDAD DE INFORMACION Este mensaje tiene carácter confidencial. Si usted no es el destinarario de este mensaje, le suplicamos se lo notifique al remitente mediante un correo electrónico y que borre el presente mensaje y sus anexos de su computadora sin retener una copia de los mismos. Queda estrictamente prohibido copiar este mensaje o hacer usode el para cualquier propósito o divulgar su en forma parcial o total su contenido. Gracias. NON-DISCLOSURE OF INFORMATION This email is strictly confidential and may also be privileged. If you are not the intended recipient please immediately advise the sender by replying to this e-mail and then deleting the message and its attachments from your computer without keeping a copy. It is strictly forbidden to copy it or use it for any purpose or disclose its contents to any third party. Thank you. On Nov 13, 2012, at 8:21 PM, John Ackermann N8UR <[email protected]> wrote: > Hello Edgardo -- > > The T2-Mini uses a wide-range input circuit based on one that Wenzel > published with some modifications. It works with a square wave input (I've > done some limited testing) but I can't verify whether the input amplitude > range will extend as far on either the low or the high side. > > If you want to drive with a true TTL signal, you could bypass the input > circuit entirely and feed directly into the PIC, though that would require > some soldering. > > John > > On Nov 13, 2012, at 6:48 PM, Edgardo Molina <[email protected]> wrote: > >> Dear Group, >> >> Does anybody know is the TAPR TADD-2 Mini works with input signals with >> square wave geometry? Or Sine wave only? >> >> Thank you. >> >> Regards, >> >> >> >> Edgardo Molina >> Dirección IPTEL >> >> www.iptel.net.mx >> >> T : 55 55 55202444 >> M : 04455 10045822 >> >> Piensa en Bits SA de CV >> >> >> >> Información anexa: >> >> >> >> >> CONFIDENCIALIDAD DE INFORMACION >> >> Este mensaje tiene carácter confidencial. Si usted no es el destinarario de >> este mensaje, le suplicamos se lo notifique al remitente mediante un correo >> electrónico y que borre el presente mensaje y sus anexos de su computadora >> sin retener una copia de los mismos. Queda estrictamente prohibido copiar >> este mensaje o hacer usode el para cualquier propósito o divulgar su en >> forma parcial o total su contenido. Gracias. >> >> >> NON-DISCLOSURE OF INFORMATION >> >> This email is strictly confidential and may also be privileged. If you are >> not the intended recipient please immediately advise the sender by replying >> to this e-mail and then deleting the message and its attachments from your >> computer without keeping a copy. It is strictly forbidden to copy it or use >> it for any purpose or disclose its contents to any third party. Thank you. >> >> >> >> >> >> >> _______________________________________________ >> time-nuts mailing list -- [email protected] >> To unsubscribe, go to https://www.febo.com/cgi-bin/mailman/listinfo/time-nuts >> and follow the instructions there. > > _______________________________________________ > time-nuts mailing list -- [email protected] > To unsubscribe, go to https://www.febo.com/cgi-bin/mailman/listinfo/time-nuts > and follow the instructions there. _______________________________________________ time-nuts mailing list -- [email protected] To unsubscribe, go to https://www.febo.com/cgi-bin/mailman/listinfo/time-nuts and follow the instructions there.
