Understood that its 3.3 yup need some regulators but I am hoping I can essentially drop the ssr into the 3801. Thanks
On Thu, Dec 20, 2012 at 10:48 AM, dlewis6767 <[email protected]>wrote: > The SSR-6t is a 3.3v device. > > > > > > > ------------------------------**-------------------- > From: "paul swed" <[email protected]> > Sent: Thursday, December 20, 2012 9:41 AM > To: "Discussion of precise time and frequency measurement" < > [email protected]> > Subject: Re: [time-nuts] SSR-6t Connector > > > Not to hijack the thread. I purchased a ssr and have not rcvd it yet. But >> my simple interest is to if needed replace the rcvr in my z3801. There >> have >> been threads on time-nuts that these rcvrs do fail with age. >> My belief is that though the connector on the 3801 may be different and it >> is 5V, essentially connecting the 1 pps TX RX data and power should allow >> this to replace the older rcvr. >> Am I on the right track? >> As a longer term goal and question does this new rcvr actually improve a >> 3801s stability? >> Thanks >> Paul >> WB8TSL >> >> On Thu, Dec 20, 2012 at 10:16 AM, David Martin < >> [email protected]> wrote: >> >> I had a Motorola M12+ all hooked up with a RF pigtail and data header so >>> I >>> just unplugged the Motorola and plugged in the SSR-6t. >>> >>> The data connector was purchased from digikey several years ago and the >>> details have been lost in the dust. >>> >>> However it looks like >>> >>> http://search.digikey.com/**scripts/DkSearch/dksus.dll?** >>> Detail&name=A33546-ND<http://search.digikey.com/scripts/DkSearch/dksus.dll?Detail&name=A33546-ND> >>> >>> I'm unhappy with the one I'm using as the contacts spring pressure is >>> weak >>> against the connector pin -- I will have to consider looking for a more >>> "firm" fitting data connector. >>> >>> The RF pigtail was also obtained years ago from data-alliance.net - >>> their >>> P3B adapter cable. >>> >>> See >>> >>> http://www.data-alliance.net/**servlet/-strse-800/MCX-BNC-** >>> female-Adapter/Detail<http://www.data-alliance.net/servlet/-strse-800/MCX-BNC-female-Adapter/Detail> >>> >>> - Sent from my iPhone - >>> Please Reply To >>> David Martin >>> [email protected] >>> 801-372-0978 >>> >>> Just curious, >>> what connector/pigtail/adapter board did you use to access the 2x5 1.27mm >>> pitch connector on your SSR-6T. >>> Thanks, >>> Dale NV8U >>> ______________________________**_________________ >>> time-nuts mailing list -- [email protected] >>> To unsubscribe, go to >>> https://www.febo.com/cgi-bin/**mailman/listinfo/time-nuts<https://www.febo.com/cgi-bin/mailman/listinfo/time-nuts> >>> and follow the instructions there. >>> >>> ______________________________**_________________ >> time-nuts mailing list -- [email protected] >> To unsubscribe, go to https://www.febo.com/cgi-bin/** >> mailman/listinfo/time-nuts<https://www.febo.com/cgi-bin/mailman/listinfo/time-nuts> >> and follow the instructions there. >> > > > ______________________________**_________________ > time-nuts mailing list -- [email protected] > To unsubscribe, go to https://www.febo.com/cgi-bin/** > mailman/listinfo/time-nuts<https://www.febo.com/cgi-bin/mailman/listinfo/time-nuts> > and follow the instructions there. > _______________________________________________ time-nuts mailing list -- [email protected] To unsubscribe, go to https://www.febo.com/cgi-bin/mailman/listinfo/time-nuts and follow the instructions there.
